similar to: No localboot on HP Proliant with Smart Array and menu.c32

Hello. Recently I've ran into problems with HP Proliant booting off the network with menu.c32. Configuration -- several identical servers: HP Proliant DL360 G5 HP Bios P58 12/26/2006 Bootblock 09/18/2006 HP SmartArray E200i Controller (128MB, v1.20) Broadcom NetXtreme II Ethernet Boot Agent v2.8.5 When localboot is chosen from menu.c32 menu I get standard "PXE-M0F Exiting ...",

Hi, I have a new server HP proliant DL320 G4, with two 160 GB SATA hdds.. I have installed CentOS 4.5 with mdadm without any problem, but when I disconnect one disk the server does not boot or I received a kernel panic when booting... I have disabled the SATA embeded raid (BIOS) and nothing.. I've also download the driver from HP site HP (Embedded SATA RAID Controller Driver Diskette for Red

I have a pxelinux I'm working with and I want the default option to be to boot off the local mbr. According to the docs, if I specify localboot 0, it should return to the BIOS and continue to the next device. When I do this, though, the pxe agent exists (PXE-M0F), but the BIOS never continues on. Is this a BIOS issue? If so, has anyone else figured out a way to work around it? * Philip

Ive got a soekris 4801 on which Ive used pxelinux... its bios is set to go to pxeboot 1st, then localboot. Ive got: label bootlocal MENU label ^9 Boot Local localboot 0 # timeout 80 # TOTALTIMEOUT 9000 but using hangs: Booting from local disk... PXE-M0F: Exiting MacPhyter PXE ROM. then nothing. the same compact flash image works fine when boot order is 80 1st, or

Hi all, I discovered lately that two of my XEN servers suffer from a really bad disk throughput - in domU as well as in dom0. All of them run Debian/Etch, Kernel 2.6.18-6-xen (orig. Debian) with XEN 3.2 (backported). The software versions seem to be ok for most machines: Lenovo A57 with S-ATA and (E8200, VT enabled): up to 90MB/s Shuttle, FB61 based, ATA-Disk (Celeron, no VT): up to

I have one HP Proliant DL320 G5p, where for some reason, the AHCI mode is not enabled. According to server specs, it should have AHCI/NCQ capability, but ata_piix module gets loaded during bootup, not ahci module. Any ideas how to enable AHCI mode? lspci output: # lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation

Sorry if this has been asked previously. Does CentOS support IDE hardware RAID on HP DL320? Thanks, -j

Hi, I have this strange problem I need some help with.. It appears that I have harddisk noise captured by a Digium TE410P card (Same problem on 2 identical machines..) The machines are two Compaq Proliant DL320 G3's... Does anyone else have this problem.. Kind Regards Claus Futtrup --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com).

I am trying to install on a DL320 proliant. The disk is not being recognized. It fails when setting up disk with "no devices" found. I dont get an sda or cciss either one. I tried to disable the on board smart array controller? That didnt seem to make a difference. Is there something special I need to do? Thanks, jerry

Hello, A couple of months back there was this message on the list. http://syslinux.zytor.com/archives/2010-October/015459.html I have exactly the same result on just a few types of machines. Acer Tavelmate 8372 and 5742 InsydeH2O Bios v1.05 Broadcom UNDI PXE 2.1 V 14.0.8 It started after I upgrades pxelinux.0 to version 3.86 Versions tested and got the recursing: 3.86, 3.85, 3.84 and 3.83 On

Hi there, I'm using pxelinux.0 to boot another pxe boot image that checks if a host needs to be installed by doing a network query. If this is not the case, this image would return and boot from the next device. But on this Broadcom card, the Message 'PXE-M0F' does not appear, so the pxe image does not return. With the latest stable the PC would recognize the keystroke

I just picked up 3.10-pre15 and the "PXELINUX corrupts graphic filename referenced from DISPLAY file" bug is zapped. Yipee! Thanks hpa. And Arwin too, if that 'xor esi,esi' was the crux. However, LOCALBOOT -1 and LOCALBOOT 0 don't work the same as they did for me in 3.07. :-( 3.07: LOCALBOOT -1 apears to work as I have a hard disk listed in bios boot order after the

hpa, etal, pxelinux works great from a push of the reset button. machine boots normally. However, after i issue 'reboot' command, my box fails to find the tftp server during reboot. This looks to be happening before pxelinux has any chance to participate, so it cannot be to blame. Im seeking corroboration here before I go badgering the bios-provider here's the relevant

Hi, I am looking to connect 66 analog phones to an asterisk box. I was thinking of a Xorcom astribank 32port (2 of them and another 8 port). this is because the phones have no near connection to an ip network, so replacing the phones in favor of voip phones+network cabling is kinda out of the question. In your experience, will these units support all the phones talking at the same time with

Hello list, I've been using PXE Boot for quite some time now and it has been working without any problems. I'm using a Biostar M7VIZ mainboard with a VIA KM400 chipset, and VIA-Rhine VT6102 NIC. Yesterday I upgrade the Kernel on my net-boot machine from 2.4.24 to 2.6.12. When I power on the machine it boots up normally. However, when I reboot the machine, the mainboards PXE-ROM only

Windows 2012 WDS server: 10.87.0.202 Windows DHCP server: 10.87.0.152 066 (Boot Server Host Name): 10.87.3.19 067 (Bootfile Name): pxelinux.0 PXELinux CentOS 7 server : 10.87.3.19 # cat /srv/tftp/pxelinux.cfg/default DEFAULT menu.c32 PROMPT 0 MENU TITLE Main Menu LABEL CentOS-7-x86_64 KERNEL CentOS-7-x86_64/vmlinuz APPEND initrd=CentOS-7-x86_64/initrd.img

I haven't encountered this problem before. This is from a Compaq DL320, with Intel Boot Agent 4.0.17 and tftp-hpa-0.28 running on Solaris. The PXE stack gets its IP address just fine, but it times out on the TFTP. While snooping on the Solaris box and grepping for TFTP, I found that the box gets one block of the TFTP transfer just fine. TFTP Read "pxelinux.0" (octet)

I saw Nate Carlson's message saying "..and it has been tested on amd64". I just installed it on an HP DL320 with Intel Pentium D 930, running i386 Sarge+backports. The packages seem to work here with Intel VT as well - in fact I just got through the Windows 2003 installation to the point where I could switch from VNC to RDP. Cool! Note to self: maybe one shoud start hacking

Hi gang! I'm using Centos 4.4 at work on a HP Proliant DL320 G2, which has a Hypterthreaded Pentium IV CPU. I used to use RHEL WS 2.1 on it, and RH installed and used the SMP kernel. Centos 4.4 did NOT install the SMP kernel. Is there some reason why I should NOT install it myself? I.e., some reason why an SMP kernel shouldn't be used on such a machine? Gracias! -- ---- Fred Smith --

I'm bringing back an old thread, but I'm still having problem with this: http://etherboot.org/pipermail/gpxe/2010-March/000571.html The summary of that thread is that with gpxelinux.0, on some computers the command LOCALBOOT 0 will hang the computer. Around the same time as the original thread, there was a patch to add localboot -1. Also in the original thread, it was proposed to use