similar to: Duplicate packets when using aggregate datalinks on bge

Hi, Can you tell why my vnic built on top of an aggregation of 2 NICs of 1 Gbit/s doesn''t report a speed of 2 GBit/s ? [root at nazgul /]# dladm show-dev bge0 link: up speed: 1000Mb duplex: full bge1 link: down speed: 0Mb duplex: unknown bge2 link: down speed: 0Mb duplex: unknown bge3 link: down speed: 0Mb

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

Recent SUP. Installed on Dell PowerEdge 4600. Getting tons of: Sep 30 12:23:16 zige /kernel: bge0: gigabit link up Sep 30 12:23:46 zige last message repeated 98 times Also getting some TCP retransmits. This causes noticable delays in pretty much everything I do now. Not a problem prior to the SUP. I was on 4.8-STABLE before. When pulling/replacing cables, it went into a mode where it would

How do I create a vnic that represents the factory assigned MAC address of my physical nic? The bge device in my system (x2100) appears to support 4 MAC addresses. The driver reserves the first as the ''primary/default'' address and allows manipulation of the other three via the MAC_CAPAB_MULTIADDRESS interface. I''d like to use vnics on this system, as I have Xen guest

Hi, how can ip instances be used with vlans ? Is that possible ? I don''t know how to configure this, if I only have one interface (e.g. bge0), and want to assign e.g. bge1000 to a zone. Any cookbooks available ? Thanks Detlef

On OpenSolaris 2009.06 I created a flow, half a dozen VNICs, and I set some properties, and everything was working, then I rebooted my system and everything disappeared from show-vnic, show-flow, and show-prop. When I tried to re-create the objects, dladm said they already existed. While I could not see the objects, I could delete them. Example: # dladm show-vnic # dladm create-vnic -l bge0

Hi all, Over the last month or so I've installed FreeBSD 9 (-stable) on several Mac Minis via the memstick image; they seem to be pretty good little boxes for things like offsite secondary nameservers, for example, and they're easily replaced in case of problems. However, the newest minis have slightly different hardware, and FreeBSD can't find the built-in NIC. pciconf -lv on the

Well this is new. I haven't a clue what Dell has done on this R620, but this popped up today after I did a boat load of BIOS updates and tried to install stable/9 from our yahoo tree. If anyone sees the obvious solution here, I'd love to figure it out. found-> vendor=0x14e4, dev=0x165f, revid=0x00 domain=0, bus=2, slot=0, func=1 class=02-00-00, hdrtype=0x00, mfdev=1

Hi, I have a server (Dell PowerEdge SC1435, ServerWorks HT1000) on which I'd like to try installing FreeBSD. I've already failed to make 7.0 work on this box and was wondering if you have information about the behavior of the upcoming 7.1 on this hardware. I've been following the "HT1000 chipset errata saga" thread, and the commits by sos@ to CVS (around Jan 2008), but have

Has anyone gotten a transparent firewall working? I''m using snv_125 on an IBM x346 (snv_130 goes into endless boot loops on this hardware). I can create a working bridge with dladm, but can''t stop packets, even with "block in quick all". That stops packets on my management interface bge0, but not on the bridge. :( tim at ghost:~# ifconfig -a lo0:

Hi, looking at the messages i see errors with ntp everytime i reboot my server: shiva2# tail /var/log/messages Apr 5 15:32:46 shiva2 kernel: Trying to mount root from ufs:/dev/da0s1a Apr 5 15:32:46 shiva2 ntpd[385]: ntpd 4.2.0-a Tue Mar 14 04:43:54 UTC 2006 (1) Apr 5 15:32:46 shiva2 ntpd[385]: bind() fd 6, family 28, port 123, addr fe80:1::20b:cdff:fe42:3d63, in6_is_addr_multicast=0 flags=0

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello All, I have had a problem detecting the network card on my notebook when ACPI is enabled for a year. The problem still exists in 7.1-RELEASE. with ACPI: ... bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002> irq 17 at device 0.0 on pci8 bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). bge0: couldn't

Hello Samba List, I'm running a Samba 3.0.22 PDC on Solaris 9. Things got a bit peculiar when I added a 2nd network interface. The two subnets are a primary network that carries all the client traffic and a tape-backup/admin network that is not accessible to any clients, ie. aaa.bbb.ccc.241 - bge0 - primary network (address suppressed) 192.168.254.254 - bge1 - admin/backup network

Hello Got strange problem with high system "%system load" and very slow user level programs (apache+php+mysql) behavior gstat shows 1.5-4% hard disk busy load but system shows about 20-30% load while user load is max 5%. vmstat shows from 2 to 35 process in "b" state. Now use 7.0-RELEASE-p5 , but the same problem was with 7.0-RELEASE. And have no idea what to do with this.

Hi all, I installed 2009.06, xVM and happily installed a domU with no issues. I just did this through the virt-manager GUI, and kept it as simple as possible. Later I installed and booted a zone with very simple and standard configuration. My existing xVM virtual machine did not immediately stop working, or have any interruption at all. But, I can no longer create new virtual machines, or even

Hi all! I am running SXCE 121 on a dual quad-core X2200M2 (64 bit of course). During an installation of a NetBSD 5.0.1 PVM domU, the entire machine crashed with a kernel panic. Here''s what I managed to salvage from the LOM console of the machine: Sep 2 18:55:19 glaurung genunix: /xpvd/xdb@41,51712 (xdb5) offline Sep 2 18:55:19 glaurung genunix: /xpvd/xdb@41,51728 (xdb6) offline

Team I have a Dell PowerEdge R720xd, with the Broadcom NetXtreme bcm5720. I found the following thread: http://forums.freebsd.org/showthread.php?t=31769 I find I am unable to use the NIC's (there are 4 on the server). When we put a cable into it we get a "watchdog timeout -- resetting" error, and the machine will pause for 5 or so seconds. IP may or may not come up randomly.