similar to: Encore/sundance boards?

Displaying 20 results from an estimated 900 matches similar to: "Encore/sundance boards?"

2007 Apr 26
1
pciback.hide sundance
Hi, I am trying to set up a Xen server using two 4-port NIC cards. The exact type: D-Link DFE 580TX. There are no problems using this cards under plain linux. The driver is called ''sundance''. But when I use pciback.hide the DomU can''t access this card. I have had the same task when using the NIC BCM 5708 (NetXtreme II). I had found a message in
2005 Aug 04
1
HELP! X100P IRQ conflict w/ USB
PC: HP Vetra VL400 Mainbood: Intel815 BIOS: Phonix 4.0 release 6.0 OS: REDHAT 9.0 I installed the X100P in PCI slot 2 and disable the USB port, serial-port and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" But I can found the card in the "cat ioports" use "lspci" I found the X100Pcard use the interrupts 11 too. Who can help me to solve
2006 Nov 01
19
pciback for usb-controller and usb-storage on x86_64 ends in Oops
Hi! I tried to pcipassthrough usb-controllers to domu to use it with a memory-stick. First xen complained that the driver needs write-access to its configuration space, so I added these to pci-quirks. Since it still didn''t work I also added the device to pci-permissive but I still get an errormessage with Oops (at the end of this email) when sticking in the memory-stick. I tried
2006 Nov 01
19
pciback for usb-controller and usb-storage on x86_64 ends in Oops
Hi! I tried to pcipassthrough usb-controllers to domu to use it with a memory-stick. First xen complained that the driver needs write-access to its configuration space, so I added these to pci-quirks. Since it still didn''t work I also added the device to pci-permissive but I still get an errormessage with Oops (at the end of this email) when sticking in the memory-stick. I tried
2007 Apr 05
1
BeroNet HFC-4S card is now detected as only 2 ports
Hello list, After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently detected as 2 ports instead of 4. I still load the driver as "modprobe qozap ports=12" as I've always done. But now it only sees 2 ports. Output of "lspci -vvv" ------ cut -------- 02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem:
2011 Mar 01
0
IRQ 0 on BRI card (B200E)
Hello list, I'm having a problem with a BRI card, a B200E (PCI-e) card on an Intel server with a riser that I'm guessing is what's making the problem. The output of lspci -vvv is: 07:00.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem: Cologne Chip Designs GmbH Device e884 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
2007 Oct 03
4
Problem with mISDN and HFC-Cards in Asterisk-DomU
Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the
2003 Jun 15
2
Ext3-Bug in Kernel 2.4.21?
Hi, The following error message appeared in syslog while the filesharing client overnet was running and writing to the disk. I first only noticed that suddenly Opera was frozen and no new terminals could be started. Regards W. Pichler syslog Jun 15 13:15:34 pc kernel: Unable to handle kernel NULL pointer dereference at virtual address 0000000e Jun 15 13:15:34 pc kernel: printing eip: Jun
2007 Apr 30
1
TDM400P and Junghanns QuadBRI issue
Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>
2014 May 21
0
kernel: NETDEV WATCHDOG: eth0 (r8169): transmit queue 0 timed out
Hi, anybody know how to fix this. May 20 12:16:15 wolfpac kernel: NETDEV WATCHDOG: eth0 (r8169): transmit queue 0 timed out May 20 12:16:15 wolfpac kernel: Modules linked in: pf_ring(U) af_key iptable_nat ipt_LOG iptable_filter ip_tables nf_conntrack_ipv6 nf_defrag_ipv6 xt_state ip6t_LOG xt_limit ip6table_filter ip6_tables bridge stp llc nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4
2006 Mar 13
1
Network card w/special module
Hello, I have this cheap network card which insists on me compiling its own sundance.ko module every time I update my kernel release. I had the poor idea to leave nightly yum service enabled on this remote server, only to find my network was gone at the following reboot. Had to go there, figure out that kernel stuff is carefully avoided by up2date, but not so by yum service, and rebuild. Compiling
2010 Apr 10
2
t200_expire: q921_state now is Q921_LINK_CONNECTION_RELEASED
Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)
2001 Dec 05
1
"Encore is not installed properly..."
HI folks, I'm trying to use Encore with wine. And I get the attached message. What mean this? Thank you very much in advance, Luis Pablo Gasparotto -------------- next part -------------- bash-2.04# wine --winver win98 encore FIXME:pthread_rwlock_rdlock FIXME:pthread_rwlock_unlock Could not stat /mnt/fd0 (No such file or directory), ignoring drive A:
2007 Feb 23
1
Encore 4.1
Marcus, I am running Encore 4.1.0.0 on Windows XP. The graphic tool works for chords but the text tool crashes whenever I exit its input mode. I copy the TTF's to the Windows font folder and it still does not work. So, I just moved the TTF's to the Windows font folder without success. Do you have a solution? Very much appreciative. Sincerely, Carl Protho -------------- next part
2011 Aug 19
0
sundance spa filters
A Clean Filter is the most important element of clean water, because it filters all the 'dirty-stuff' from the water. Clogged Filters don't work so you need to deep-clean or replace your filter(s) on a regular basis. For more details visit:http://www.spa-daddy.com/
2004 Sep 19
4
X100p on VIA EPIA-V problems
Hi All, I hope I'm posting this to the appriopriate list, and that cross posting to two lists is OK. (If not, I'm sure I'll hear about it quickly :)) I'm running Asterisk on my (new) VIA EPIA-V motherboard. This seems to be the ideal platform for a home version of asterisk - its small, quiet, low power, and should have plenty of computing horsepower if only it would work!
2013 Mar 15
0
Fwd: atheros wifi on my oqo2
---------- Forwarded message ---------- From: SilverTip257 <silvertip257 at gmail.com> Date: Fri, Mar 15, 2013 at 7:51 PM Subject: Re: [CentOS] atheros wifi on my oqo2 To: Robert Moskowitz <rgm at htt-consult.com> On Fri, Mar 15, 2013 at 5:07 PM, Robert Moskowitz <rgm at htt-consult.com>wrote: > > On 03/14/2013 07:09 PM, SilverTip257 wrote: > >> On Thu, Mar 14,
2006 May 12
7
Xen Kernel (3.0.2) breaks b44 module
I have a new laptop (Dell 9400) that I am trying to work with Xen 3.0. Xen works fine, runs windows XP under HVM. But, the Xen kernel on Dom0 has a few problems with some of the hardware. The network card is a Broadcom 4400 10/100BaseT. Normally loading the b44 module gives this: Apr 28 20:07:53 ipanema kernel: [4294683.185000] b44.c:v0.97 (Nov 30, 2005) Apr 28 20:07:53 ipanema kernel:
2004 Jan 22
1
PROBLEM: Filesystem became readonly, then kernel crashes on shutdown
Hi All, I just had "an issue" with my Linux 2.6.1 kernel. While working, I tried to rf -rf a directory, and was told my filesystem was mounted readonly (which it wasn't). I then shut the machine down, and on shutdown, I got a "kernel BUG at fs/ext3/super.c: 411". Full report below: Mike [1.] One line summary of the problem: Filesystem became readonly, then
2014 Apr 09
2
Assistance in tracking a kernel/nouveau error
Ack! This slipped through my email. I am terribly sorry. Thank you so much for responding. On 04/06/2014 08:43 PM, Ilia Mirkin wrote: > On Sun, Apr 6, 2014 at 7:16 PM, ~Stack~ <i.am.stack at gmail.com> wrote: >> Greetings, [snip] >> My working kernel is: 2.6.32-358.23.2.el6.x86_64 (and anything before). >> >> The problem kernel is: 2.6.32-431.1.2.el6.x86_64 and