I am puzzled. I started setting up a new box last week with
Linux 2.6.10.
Everything was working fine until I went to start shorewall,
when all network traffic stopped.
I have little doubt that it is because I missed something in
configuring the machine. I''m running shorewall 2.2 and the zone,
policy, and rules files are cut and paste from a machine that
has been running for over a year with no issues. I suspect I
missed something in the kernel configuration as this is my first
go at using 2.6.
I have attached my kernel .config file as well as the zones,
rules, and policy files.
Any insights will be greatly appreciated.
--Richard
#
# Shorewall 2.2 /etc/shorewall/zones
#
# This file determines your network zones. Columns are:
#
# ZONE Short name of the zone (5 Characters or less in length).
# DISPLAY Display name of the zone
# COMMENTS Comments about the zone
#
# THE ORDER OF THE ENTRIES IN THIS FILE IS IMPORTANT IF YOU HAVE NESTED OR
# OVERLAPPING ZONES DEFINED THROUGH /etc/shorewall/hosts.
#
# See http://www.shorewall.net/Documentation.htm#Nested
#
#ZONE DISPLAY COMMENTS
net Net Internet
#LAST LINE - ADD YOUR ENTRIES ABOVE THIS ONE - DO NOT REMOVE
#
# Shorewall version 2.2 - Rules File
#
# /etc/shorewall/rules
#
# Rules in this file govern connection establishment. Requests and
# responses are automatically allowed using connection tracking. For any
# particular (source,dest) pair of zones, the rules are evaluated in the
# order in which they appear in this file and the first match is the one
# that determines the disposition of the request.
#
# In most places where an IP address or subnet is allowed, you
# can preceed the address/subnet with "!" (e.g., !192.168.1.0/24) to
# indicate that the rule matches all addresses except the address/subnet
# given. Notice that no white space is permitted between "!" and the
# address/subnet.
#------------------------------------------------------------------------------
# WARNING: If you masquerade or use SNAT from a local system to the internet,
# you cannot use an ACCEPT rule to allow traffic from the internet to
# that system. You *must* use a DNAT rule instead.
#-------------------------------------------------------------------------------#
# Columns are:
#
# ACTION ACCEPT, DROP, REJECT, DNAT, DNAT-, REDIRECT, CONTINUE,
# LOG, QUEUE or an <action>.
#
# ACCEPT -- allow the connection request
# ACCEPT+ -- like ACCEPT but also excludes the
# connection from any subsequent
# DNAT[-] or REDIRECT[-] rules
# NONAT -- Excludes the connection from any
# subsequent DNAT[-] or REDIRECT[-]
# rules but doesn''t generate a rule
# to accept the traffic.
# DROP -- ignore the request
# REJECT -- disallow the request and return an
# icmp-unreachable or an RST packet.
# DNAT -- Forward the request to another
# system (and optionally another
# port).
# DNAT- -- Advanced users only.
# Like DNAT but only generates the
# DNAT iptables rule and not
# the companion ACCEPT rule.
# REDIRECT -- Redirect the request to a local
# port on the firewall.
# REDIRECT-
# -- Advanced users only.
# Like REDIRET but only generates the
# REDIRECT iptables rule and not
# the companion ACCEPT rule.
#
# CONTINUE -- (For experts only). Do not process
# any of the following rules for this
# (source zone,destination zone). If
# The source and/or destination IP
# address falls into a zone defined
# later in /etc/shorewall/zones, this
# connection request will be passed
# to the rules defined for that
# (those) zone(s).
# LOG -- Simply log the packet and continue.
# QUEUE -- Queue the packet to a user-space
# application such as ftwall
# (http://p2pwall.sf.net).
# <action> -- The name of an action defined in
# /etc/shorewall/actions or in
# /usr/share/shorewall/actions.std.
#
# The ACTION may optionally be followed
# by ":" and a syslog log level (e.g, REJECT:info or
# DNAT:debug). This causes the packet to be
# logged at the specified level.
#
# If the ACTION names an action defined in
# /etc/shorewall/actions or in
# /usr/share/shorewall/actions.std then:
#
# - If the log level is followed by "!'' then all rules
# in the action are logged at the log level.
#
# - If the log level is not followed by "!" then only
# those rules in the action that do not specify
# logging are logged at the specified level.
#
# - The special log level ''none!'' suppresses logging
# by the action.
#
# You may also specify ULOG (must be in upper case) as a
# log level.This will log to the ULOG target for routing
# to a separate log through use of ulogd
# (http://www.gnumonks.org/projects/ulogd).
#
# Actions specifying logging may be followed by a
# log tag (a string of alphanumeric characters)
# are appended to the string generated by the
# LOGPREFIX (in /etc/shorewall/shorewall.conf).
#
# Example: ACCEPT:info:ftp would include ''ftp ''
# at the end of the log prefix generated by the
# LOGPREFIX setting.
#
# SOURCE Source hosts to which the rule applies. May be a zone
# defined in /etc/shorewall/zones, $FW to indicate the
# firewall itself, or "all" If the ACTION is DNAT or
# REDIRECT, sub-zones of the specified zone may be
# excluded from the rule by following the zone name with
# "!'' and a comma-separated list of sub-zone names.
#
# When "all" is used either in the SOURCE or DEST column
# intra-zone traffic is not affected. You must add
# separate rules to handle that traffic.
#
# Except when "all" is specified, clients may be further
# restricted to a list of subnets and/or hosts by
# appending ":" and a comma-separated list of subnets
# and/or hosts. Hosts may be specified by IP or MAC
# address; mac addresses must begin with "~" and must use
# "-" as a separator.
#
# Hosts may be specified as an IP address range using the
# syntax <low address>-<high address>. This requires that
# your kernel and iptables contain iprange match support.
#
# dmz:192.168.2.2 Host 192.168.2.2 in the DMZ
#
# net:155.186.235.0/24 Subnet 155.186.235.0/24 on the
# Internet
#
# loc:192.168.1.1,192.168.1.2
# Hosts 192.168.1.1 and
# 192.168.1.2 in the local zone.
# loc:~00-A0-C9-15-39-78 Host in the local zone with
# MAC address 00:A0:C9:15:39:78.
#
# net:192.0.2.11-192.0.2.17
# Hosts 192.0.2.11-192.0.2.17 in
# the net zone.
#
# Alternatively, clients may be specified by interface
# by appending ":" to the zone name followed by the
# interface name. For example, loc:eth1 specifies a
# client that communicates with the firewall system
# through eth1. This may be optionally followed by
# another colon (":") and an IP/MAC/subnet address
# as described above (e.g., loc:eth1:192.168.1.5).
#
# DEST Location of Server. May be a zone defined in
# /etc/shorewall/zones, $FW to indicate the firewall
# itself or "all"
#
# When "all" is used either in the SOURCE or DEST column
# intra-zone traffic is not affected. You must add
# separate rules to handle that traffic.
#
# Except when "all" is specified, the server may be
# further restricted to a particular subnet, host or
# interface by appending ":" and the subnet, host or
# interface. See above.
#
# Restrictions:
#
# 1. MAC addresses are not allowed.
# 2. In DNAT rules, only IP addresses are
# allowed; no FQDNs or subnet addresses
# are permitted.
# 3. You may not specify both an interface and
# an address.
#
# Like in the SOURCE column, you may specify a range of
# up to 256 IP addresses using the syntax
# <first ip>-<last ip>. When the ACTION is DNAT or DNAT-,
# the connections will be assigned to addresses in the
# range in a round-robin fashion.
#
# The port that the server is listening on may be
# included and separated from the server''s IP address by
# ":". If omitted, the firewall will not modifiy the
# destination port. A destination port may only be
# included if the ACTION is DNAT or REDIRECT.
#
# Example: loc:192.168.1.3:3128 specifies a local
# server at IP address 192.168.1.3 and listening on port
# 3128. The port number MUST be specified as an integer
# and not as a name from /etc/services.
#
# if the ACTION is REDIRECT, this column needs only to
# contain the port number on the firewall that the
# request should be redirected to.
#
# PROTO Protocol - Must be "tcp", "udp", "icmp",
"ipp2p",
# a number, or "all". "ipp2p" requires ipp2p match
# support in your kernel and iptables.
#
# DEST PORT(S) Destination Ports. A comma-separated list of Port
# names (from /etc/services), port numbers or port
# ranges; if the protocol is "icmp", this column is
# interpreted as the destination icmp-type(s).
#
# If the protocol is ipp2p, this column is interpreted
# as an ipp2p option without the leading "--" (example
"bit"
# for bit-torrent). If no port is given, "ipp2p" is
# assumed.
#
# A port range is expressed as <low port>:<high port>.
#
# This column is ignored if PROTOCOL = all but must be
# entered if any of the following ields are supplied.
# In that case, it is suggested that this field contain
# "-"
#
# If your kernel contains multi-port match support, then
# only a single Netfilter rule will be generated if in
# this list and the CLIENT PORT(S) list below:
# 1. There are 15 or less ports listed.
# 2. No port ranges are included.
# Otherwise, a separate rule will be generated for each
# port.
#
# CLIENT PORT(S) (Optional) Port(s) used by the client. If omitted,
# any source port is acceptable. Specified as a comma-
# separated list of port names, port numbers or port
# ranges.
#
# If you don''t want to restrict client ports but need to
# specify an ORIGINAL DEST in the next column, then place
# "-" in this column.
#
# If your kernel contains multi-port match support, then
# only a single Netfilter rule will be generated if in
# this list and the DEST PORT(S) list above:
# 1. There are 15 or less ports listed.
# 2. No port ranges are included.
# Otherwise, a separate rule will be generated for each
# port.
#
# ORIGINAL DEST (0ptional -- only allowed if ACTION is DNAT[-] or
# REDIRECT[-]) If included and different from the IP
# address given in the SERVER column, this is an address
# on some interface on the firewall and connections to
# that address will be forwarded to the IP and port
# specified in the DEST column.
#
# A comma-separated list of addresses may also be used.
# This is usually most useful with the REDIRECT target
# where you want to redirect traffic destined for
# particular set of hosts.
#
# Finally, if the list of addresses begins with "!" then
# the rule will be followed only if the original
# destination address in the connection request does not
# match any of the addresses listed.
#
# RATE LIMIT You may rate-limit the rule by placing a value in
# this colume:
#
# <rate>/<interval>[:<burst>]
#
# where <rate> is the number of connections per
# <interval> ("sec" or "min") and <burst> is
the
# largest burst permitted. If no <burst> is given,
# a value of 5 is assumed. There may be no
# no whitespace embedded in the specification.
#
# Example: 10/sec:20
#
# USER/GROUP This column may only be non-empty if the SOURCE is
# the firewall itself.
#
# The column may contain:
#
# [!][<user name or number>][:<group name or number>]
#
# When this column is non-empty, the rule applies only
# if the program generating the output is running under
# the effective <user> and/or <group> specified (or is
# NOT running under that id if "!" is given).
#
# Examples:
#
# joe #program must be run by joe
# :kids #program must be run by a member of
# #the ''kids'' group
# !:kids #program must not be run by a member
# #of the ''kids'' group
#
# Example: Accept SMTP requests from the DMZ to the internet
#
# #ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL
# # PORT PORT(S) DEST
# ACCEPT dmz net tcp smtp
#
# Example: Forward all ssh and http connection requests from the internet
# to local system 192.168.1.3
#
# #ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL
# # PORT PORT(S) DEST
# DNAT net loc:192.168.1.3 tcp ssh,http
#
# Example: Forward all http connection requests from the internet
# to local system 192.168.1.3 with a limit of 3 per second and
# a maximum burst of 10
#
# #ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL RATE
# # PORT PORT(S) DEST LIMIT
# DNAT net loc:192.168.1.3 tcp http - - 3/sec:10
#
# Example: Redirect all locally-originating www connection requests to
# port 3128 on the firewall (Squid running on the firewall
# system) except when the destination address is 192.168.2.2
#
# #ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL
# # PORT PORT(S) DEST
# REDIRECT loc 3128 tcp www - !192.168.2.2
#
# Example: All http requests from the internet to address
# 130.252.100.69 are to be forwarded to 192.168.1.3
#
# #ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL
# # PORT PORT(S) DEST
# DNAT net loc:192.168.1.3 tcp 80 - 130.252.100.69
#
# Example: You want to accept SSH connections to your firewall only
# from internet IP addresses 130.252.100.69 and 130.252.100.70
#
# #ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL
# # PORT PORT(S) DEST
# ACCEPT net:130.252.100.69,130.252.100.70 fw \
# tcp 22
####################################################################################################
#ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL RATE USER/
# PORT PORT(S) DEST LIMIT GROUP
#
ACCEPT net fw tcp ssh
ACCEPT net fw tcp domain
ACCEPT net fw udp domain
ACCEPT net fw tcp 80,443,8080
ACCEPT net fw tcp pop3,smtp
ACCEPT net fw tcp ftp,ftp-data
ACCEPT net fw tcp 953
ACCEPT fw fw tcp domain
ACCEPT fw fw udp domain
ACCEPT fw fw tcp 953
ACCEPT fw fw tcp 389
ACCEPT fw fw udp tftp
ACCEPT fw fw tcp mysql
ACCEPT fw fw tcp 10024,10025
ACCEPT fw fw tcp smtp,pop3
ACCEPT fw net udp tftp
ACCEPT fw fw tcp ntp
ACCEPT fw fw udp ntp
# postgresql
ACCEPT fw fw tcp 5432
ACCEPT fw fw tcp 3601
#LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE
#
# Shorewall 2.2 -- Policy File
#
# /etc/shorewall/policy
#
# THE ORDER OF ENTRIES IN THIS FILE IS IMPORTANT
#
# This file determines what to do with a new connection request if we
# don''t get a match from the /etc/shorewall/rules file . For each
# source/destination pair, the file is processed in order until a
# match is found ("all" will match any client or server).
#
# Columns are:
#
# SOURCE Source zone. Must be the name of a zone defined
# in /etc/shorewall/zones, $FW or "all".
#
# DEST Destination zone. Must be the name of a zone defined
# in /etc/shorewall/zones, $FW or "all"
#
# POLICY Policy if no match from the rules file is found. Must
# be "ACCEPT", "DROP", "REJECT",
"CONTINUE" or "NONE".
#
# ACCEPT - Accept the connection
# DROP - Ignore the connection request
# REJECT - For TCP, send RST. For all other, send
# "port unreachable" ICMP.
# CONTINUE - Pass the connection request past
# any other rules that it might also
# match (where the source or destination
# zone in those rules is a superset of
# the SOURCE or DEST in this policy).
# NONE - Assume that there will never be any
# packets from this SOURCE
# to this DEST. Shorewall will not set up
# any infrastructure to handle such
# packets and you may not have any rules
# with this SOURCE and DEST in the
# /etc/shorewall/rules file. If such a
# packet _is_ received, the result is
# undefined. NONE may not be used if the
# SOURCE or DEST columns contain the
# firewall zone ($FW) or "all".
#
# If this column contains ACCEPT, DROP or REJECT and a
# corresponding common action is defined in
# /etc/shorewall/actions (or /usr/share/shorewall/actions.std)
# then that action will be invoked before the policy named in
# this column is inforced.
#
# LOG LEVEL If supplied, each connection handled under the default
# POLICY is logged at that level. If not supplied, no
# log message is generated. See syslog.conf(5) for a
# description of log levels.
#
# Beginning with Shorewall version 1.3.12, you may
# also specify ULOG (must be in upper case). This will
# log to the ULOG target and sent to a separate log
# through use of ulogd
# (http://www.gnumonks.org/projects/ulogd).
#
# If you don''t want to log but need to specify the
# following column, place "-" here.
#
# LIMIT:BURST If passed, specifies the maximum TCP connection rate
# and the size of an acceptable burst. If not specified,
# TCP connections are not limited.
#
# As shipped, the default policies are:
#
# a) All connections from the local network to the internet are allowed
# b) All connections from the internet are ignored but logged at syslog
# level KERNEL.INFO.
# d) All other connection requests are rejected and logged at level
# KERNEL.INFO.
###############################################################################
#SOURCE DEST POLICY LOG LIMIT:BURST
# LEVEL
#
fw net ACCEPT
net all DROP
all all REJECT
#
#LAST LINE -- DO NOT REMOVE
#
# Automatically generated make config: don''t edit
# Linux kernel version: 2.6.10-as2
# Mon Feb 14 19:28:43 2005
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_FUTEX=y
CONFIG_EPOLL=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
# CONFIG_HPET_TIMER is not set
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
# CONFIG_X86_MCE_P4THERMAL is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y
# CONFIG_REGPARM is not set
#
# Power management options (ACPI, APM)
#
# CONFIG_PM is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
# CONFIG_ACPI is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCI_MSI is not set
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PC-card bridges
#
CONFIG_PCMCIA_PROBE=y
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_OTHER is not set
# CONFIG_PARPORT_1284 is not set
#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
CONFIG_ISAPNP=y
# CONFIG_PNPBIOS is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
CONFIG_BLK_CPQ_DA=y
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_LBD is not set
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=y
# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
#
# CONFIG_BLK_DEV_SD is not set
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
CONFIG_SCSI_DPT_I2O=m
# CONFIG_SCSI_IN2000 is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_AHCI is not set
# CONFIG_SCSI_SATA_SVW is not set
CONFIG_SCSI_ATA_PIIX=y
# CONFIG_SCSI_SATA_NV is not set
# CONFIG_SCSI_SATA_PROMISE is not set
CONFIG_SCSI_SATA_SX4=m
# CONFIG_SCSI_SATA_SIL is not set
CONFIG_SCSI_SATA_SIS=m
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
CONFIG_SCSI_IPR=m
# CONFIG_SCSI_IPR_TRACE is not set
# CONFIG_SCSI_IPR_DUMP is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_CRYPT is not set
# CONFIG_DM_SNAPSHOT is not set
# CONFIG_DM_MIRROR is not set
# CONFIG_DM_ZERO is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_MULTIPATH=y
# CONFIG_IP_ROUTE_VERBOSE is not set
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=y
CONFIG_NET_IPGRE=y
# CONFIG_NET_IPGRE_BROADCAST is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
CONFIG_INET_TUNNEL=y
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
CONFIG_NETFILTER_DEBUG=y
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=y
# CONFIG_IP_NF_CT_ACCT is not set
CONFIG_IP_NF_CONNTRACK_MARK=y
# CONFIG_IP_NF_CT_PROTO_SCTP is not set
CONFIG_IP_NF_FTP=y
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_MATCH_LIMIT=y
CONFIG_IP_NF_MATCH_IPRANGE=y
CONFIG_IP_NF_MATCH_MAC=y
CONFIG_IP_NF_MATCH_PKTTYPE=y
CONFIG_IP_NF_MATCH_MARK=y
CONFIG_IP_NF_MATCH_MULTIPORT=y
CONFIG_IP_NF_MATCH_TOS=y
CONFIG_IP_NF_MATCH_RECENT=y
CONFIG_IP_NF_MATCH_ECN=y
CONFIG_IP_NF_MATCH_DSCP=y
CONFIG_IP_NF_MATCH_AH_ESP=y
CONFIG_IP_NF_MATCH_LENGTH=y
CONFIG_IP_NF_MATCH_TTL=y
CONFIG_IP_NF_MATCH_TCPMSS=y
CONFIG_IP_NF_MATCH_HELPER=y
CONFIG_IP_NF_MATCH_STATE=y
CONFIG_IP_NF_MATCH_CONNTRACK=y
CONFIG_IP_NF_MATCH_OWNER=y
CONFIG_IP_NF_MATCH_ADDRTYPE=y
# CONFIG_IP_NF_MATCH_REALM is not set
# CONFIG_IP_NF_MATCH_SCTP is not set
# CONFIG_IP_NF_MATCH_COMMENT is not set
CONFIG_IP_NF_MATCH_CONNMARK=y
# CONFIG_IP_NF_MATCH_HASHLIMIT is not set
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_ULOG=y
CONFIG_IP_NF_TARGET_TCPMSS=y
CONFIG_IP_NF_NAT=y
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=y
CONFIG_IP_NF_TARGET_REDIRECT=y
CONFIG_IP_NF_TARGET_NETMAP=y
CONFIG_IP_NF_TARGET_SAME=y
CONFIG_IP_NF_NAT_LOCAL=y
# CONFIG_IP_NF_NAT_SNMP_BASIC is not set
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=y
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_TOS=y
CONFIG_IP_NF_TARGET_ECN=y
CONFIG_IP_NF_TARGET_DSCP=y
CONFIG_IP_NF_TARGET_MARK=y
CONFIG_IP_NF_TARGET_CLASSIFY=y
# CONFIG_IP_NF_TARGET_CONNMARK is not set
# CONFIG_IP_NF_TARGET_CLUSTERIP is not set
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=y
CONFIG_IP_NF_ARPFILTER=y
CONFIG_IP_NF_ARP_MANGLE=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
CONFIG_HAMRADIO=y
#
# Packet Radio protocols
#
CONFIG_AX25=m
# CONFIG_AX25_DAMA_SLAVE is not set
CONFIG_NETROM=m
CONFIG_ROSE=m
#
# AX.25 network device drivers
#
CONFIG_MKISS=m
# CONFIG_6PACK is not set
# CONFIG_BPQETHER is not set
# CONFIG_DMASCC is not set
# CONFIG_SCC is not set
# CONFIG_BAYCOM_SER_FDX is not set
# CONFIG_BAYCOM_SER_HDX is not set
# CONFIG_BAYCOM_PAR is not set
# CONFIG_BAYCOM_EPP is not set
# CONFIG_YAM is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_CS89x0 is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
CONFIG_8139TOO=y
# CONFIG_8139TOO_PIO is not set
CONFIG_8139TOO_TUNE_TWISTER=y
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=y
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
# CONFIG_PPP_ASYNC is not set
# CONFIG_PPP_SYNC_TTY is not set
# CONFIG_PPP_DEFLATE is not set
# CONFIG_PPP_BSDCOMP is not set
CONFIG_PPPOE=y
CONFIG_SLIP=m
# CONFIG_SLIP_COMPRESSED is not set
# CONFIG_SLIP_SMART is not set
# CONFIG_SLIP_MODE_SLIP6 is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
# CONFIG_SERIO_RAW is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_UINPUT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_PRINTER=y
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=y
CONFIG_AGP_INTEL_MCH=m
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# Dallas''s 1-wire bus
#
# CONFIG_W1 is not set
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
# CONFIG_FB is not set
CONFIG_VIDEO_SELECT=y
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_SEQUENCER=y
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# ISA devices
#
# CONFIG_SND_AD1816A is not set
# CONFIG_SND_AD1848 is not set
# CONFIG_SND_CS4231 is not set
# CONFIG_SND_CS4232 is not set
# CONFIG_SND_CS4236 is not set
# CONFIG_SND_ES968 is not set
# CONFIG_SND_ES1688 is not set
# CONFIG_SND_ES18XX is not set
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
# CONFIG_SND_OPTI92X_AD1848 is not set
# CONFIG_SND_OPTI92X_CS4231 is not set
# CONFIG_SND_OPTI93X is not set
# CONFIG_SND_SB8 is not set
# CONFIG_SND_SB16 is not set
# CONFIG_SND_SBAWE is not set
# CONFIG_SND_WAVEFRONT is not set
# CONFIG_SND_ALS100 is not set
# CONFIG_SND_AZT2320 is not set
# CONFIG_SND_CMI8330 is not set
# CONFIG_SND_DT019X is not set
# CONFIG_SND_OPL3SA2 is not set
# CONFIG_SND_SGALAXY is not set
# CONFIG_SND_SSCAPE is not set
#
# PCI devices
#
CONFIG_SND_AC97_CODEC=y
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=y
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VX222 is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB=y
CONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_OHCI_HCD is not set
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y
#
# NOTE: USB_STORAGE enables SCSI, and ''SCSI disk support'' may
also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
CONFIG_USB_STORAGE_DEBUG=y
# CONFIG_USB_STORAGE_RW_DETECT is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
CONFIG_USB_EGALAX=m
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
CONFIG_USB_CYTHERM=m
# CONFIG_USB_PHIDGETKIT is not set
CONFIG_USB_PHIDGETSERVO=m
# CONFIG_USB_TEST is not set
#
# USB ATM/DSL drivers
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
# CONFIG_EXPORTFS is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_FRAME_POINTER is not set
CONFIG_EARLY_PRINTK=y
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_WP512=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_BLOWFISH=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_SERPENT=y
CONFIG_CRYPTO_AES_586=y
CONFIG_CRYPTO_CAST5=y
CONFIG_CRYPTO_CAST6=y
CONFIG_CRYPTO_TEA=y
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_KHAZAD=y
CONFIG_CRYPTO_ANUBIS=y
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_TEST=y
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
Richard Pyne wrote:> I am puzzled. I started setting up a new box last week with > Linux 2.6.10. > > Everything was working fine until I went to start shorewall, > when all network traffic stopped. > > I have little doubt that it is because I missed something in > configuring the machine. I''m running shorewall 2.2 and the zone, > policy, and rules files are cut and paste from a machine that > has been running for over a year with no issues. I suspect I > missed something in the kernel configuration as this is my first > go at using 2.6. > > I have attached my kernel .config file as well as the zones, > rules, and policy files. > > Any insights will be greatly appreciated.Please go to the Shorewall Support Guide page (http://shorewall.net/support.htm) and learn about what information we need to solve this sort of problem. Pay particular attention to the bullet that begins THIS IS IMPORTANT! -Tom -- Tom Eastep \ Nothing is foolproof to a sufficiently talented fool Shoreline, \ http://shorewall.net Washington USA \ teastep@shorewall.net PGP Public Key \ https://lists.shorewall.net/teastep.pgp.key
rpyne@shopsite.com
2005-Feb-16 18:58 UTC
Re: Starting shorewall blocks all traffic - linux 2.6
On 15 Feb 2005 at 19:18, Tom Eastep wrote:> Richard Pyne wrote: > > I am puzzled. I started setting up a new box last week with > > Linux 2.6.10. > > > > Everything was working fine until I went to start shorewall, > > when all network traffic stopped. > > > > I have little doubt that it is because I missed something in > > configuring the machine. I''m running shorewall 2.2 and the zone, > > policy, and rules files are cut and paste from a machine that > > has been running for over a year with no issues. I suspect I > > missed something in the kernel configuration as this is my first > > go at using 2.6. > > > > I have attached my kernel .config file as well as the zones, > > rules, and policy files. > > > > Any insights will be greatly appreciated. > > Please go to the Shorewall Support Guide page > (http://shorewall.net/support.htm) and learn about what information we > need to solve this sort of problem. Pay particular attention to the > bullet that begins THIS IS IMPORTANT!My apologies. root@ns3 ~ # shorewall version 2.2.0 root@ns3 ~ # ip addr show 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:50:ba:d3:3c:ec brd ff:ff:ff:ff:ff:ff inet 67.50.205.82/27 brd 67.50.205.255 scope global eth0 3: tunl0: <NOARP> mtu 1480 qdisc noop link/ipip 0.0.0.0 brd 0.0.0.0 4: gre0: <NOARP> mtu 1476 qdisc noop link/gre 0.0.0.0 brd 0.0.0.0 root@ns3 ~ # ip route show 67.50.205.64/27 dev eth0 proto kernel scope link src 67.50.205.82 127.0.0.0/8 dev lo scope link default via 67.50.205.65 dev eth0 root@ns3 ~ # Attached is the status.txt file --Richard The following section of this message contains a file attachment prepared for transmission using the Internet MIME message format. If you are using Pegasus Mail, or any other MIME-compliant system, you should be able to save it or view it from within your mailer. If you cannot, please ask your system administrator for assistance. ---- File information ----------- File: status.txt Date: 16 Feb 2005, 11:46 Size: 19179 bytes. Type: Text
rpyne@shopsite.com wrote:> > root@ns3 ~ # shorewall version > 2.2.0 > root@ns3 ~ # ip addr show > 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue > link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 > inet 127.0.0.1/8 scope host lo > 2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 > link/ether 00:50:ba:d3:3c:ec brd ff:ff:ff:ff:ff:ff > inet 67.50.205.82/27 brd 67.50.205.255 scope global eth0 > 3: tunl0: <NOARP> mtu 1480 qdisc noop > link/ipip 0.0.0.0 brd 0.0.0.0 > 4: gre0: <NOARP> mtu 1476 qdisc noop > link/gre 0.0.0.0 brd 0.0.0.0 > root@ns3 ~ # ip route show > 67.50.205.64/27 dev eth0 proto kernel scope link src 67.50.205.82 > 127.0.0.0/8 dev lo scope link > default via 67.50.205.65 dev eth0 > root@ns3 ~ # > > > Attached is the status.txt file >Your net zone is empty! You forgot to configure it in the interfaces and/or host file(s). -Tom -- Tom Eastep \ Nothing is foolproof to a sufficiently talented fool Shoreline, \ http://shorewall.net Washington USA \ teastep@shorewall.net PGP Public Key \ https://lists.shorewall.net/teastep.pgp.key
rpyne@shopsite.com
2005-Feb-16 19:21 UTC
Re: Starting shorewall blocks all traffic - linux 2.6
On 16 Feb 2005 at 11:03, Tom Eastep wrote:> rpyne@shopsite.com wrote: > > > > > root@ns3 ~ # shorewall version > > 2.2.0 > > root@ns3 ~ # ip addr show > > 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue > > link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 > > inet 127.0.0.1/8 scope host lo > > 2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 > > link/ether 00:50:ba:d3:3c:ec brd ff:ff:ff:ff:ff:ff > > inet 67.50.205.82/27 brd 67.50.205.255 scope global eth0 > > 3: tunl0: <NOARP> mtu 1480 qdisc noop > > link/ipip 0.0.0.0 brd 0.0.0.0 > > 4: gre0: <NOARP> mtu 1476 qdisc noop > > link/gre 0.0.0.0 brd 0.0.0.0 > > root@ns3 ~ # ip route show > > 67.50.205.64/27 dev eth0 proto kernel scope link src 67.50.205.82 > > 127.0.0.0/8 dev lo scope link > > default via 67.50.205.65 dev eth0 > > root@ns3 ~ # > > > > > > Attached is the status.txt file > > > > Your net zone is empty! You forgot to configure it in the interfaces > and/or host file(s).I guess I am a sufficiently talented fool. I missed it in the interfaces file. Thank you very much for helping me at least wipe eye holes through the egg on my face. --Richard
Reasonably Related Threads
- DNAT not working after changing BIND to use views
- DNAT + Masq Problem - Yes I read the FAQ I promise
- cannot establish connections from the machine to the internet
- Problem with Internal accessing internal via web
- start error "invalid interface" on shorewall 2.08