search for: vncserver

I am trying to setup a centos 7.1 vncserver I cannot believe they went from a relatively easy process in 6 to the "crazyness" that is 7. I did the following: yum install tigervnc-server cp /lib/systemd/system/vncserver at .service /etc/systemd/system systemctl daemon-reload...

OK, first time configuring vncserver on Centos7. I have read through a bunch of old messages here on vncserver and thought I had it. Obviously not. 1) cp /usr/lib/systemd/system/vncserver at .service /etc/systemd/system/vncserver at .service 2) vi /etc/systemd/system/vncserver at .service I changed <USER> in both pl...

HI all, i am configuring VNC server in CentOS 5.1. i have enables this two lines in /etc/sysconfig/vncserver file VNCSERVERS="2:vnc" VNCSERVERARGS[2]="-geometry 1024x768 -depth 24" here i have created a user vnc and set the password using vncpasswd cmd. then i started the vncserver # vncserver New 'localhost.localdomain:1 (gopinath)' desktop is lo...

I get back from two weeks on the road, and try to VNC to my server and it fails. I ssh in and see that, yes vncserver is dead. I tried restarting it and see below for the failure messages plus my systemd setup. Can someone point me to trouble shooting why it says about resources (if that is the problem); # systemctl -l status vncserver@:3.service ? vncserver@:3.service - Remote desktop service (VNC) Loade...

...in VNC Server E4.1.7/P4.1.2 VNC Server E4.1.7 & P4.1.2 are fully IPv6-aware, but is shipped with IPv6 support disabled by default, for security reasons. IPv6 can be enabled by setting "InTransports=IPv6,IPv4" (the default being IPv4 only), either on the command-line when starting vncserver under Unix Ok. we have vnc-server-4.1.2-9.el5.i386.rpm, so it SHOULD support IPv6. Don't know how to add a setting to the command-line, as I rund VNCserver via the service command, but I added it to /etc/sysconfig/vncservers: InTransports="IPv6" (note I also tried without the q...

When I run system-config-services, it shows vncserver set to start at boot. in /etc/inittab I have init 3 vncserver does not start at boot. I log in on the console as root and service vncserver start and it starts with some warning messages about bad display name in "add" command, but I do not see where these are logged to copy them in...

>You should: >cp /lib/systemd/system/vncserver at .service <http://lists.centos.org/mailman/listinfo/centos> /lib/systemd/system/vncserver@:#.service >Where # is the vnc port 590# to open. Like /lib/systemd/system/vncserver@:4.service to start a vncserver on port 5904. > Then use `systemctl start vncserver@:4' to start that V...

I got vncserver working per: https://www.tecmint.com/install-and-configure-vnc-server-in-centos-7/ Then I went to set up a second instance, and have that for logging on to root: ========== cp /lib/systemd/system/vncserver at .service /etc/systemd/system/vncserver@:2.service vi /etc/systemd/system/vncserver@...

...::5902 :::* LISTEN tcp6 0 0 :::5903 :::* LISTEN Why 5901 and 2 are listening, I don't know... when I vnc to my server I get that basic nasty blank X11 screen. I modified /root/.vnc/xstartup with: exec /bin/sh /etc/xdg/xfce4/xinitrc But restarting vncserver@:3 does not seem to get the vnc client to get my xfce desktop, only the blank x11 desktop. Oh and restart gives the same errors as start does, but the pids are there: # ls .vnc/ homebase.home.htt:1.log homebase.home.htt:2.pid passwd homebase.home.htt:1.pid homebase.home.htt:3.log xstartup ho...

Hi, I just installed CentOS7 and managed to start the vncserver service, but once I connect to the machine, the desktop resolution isn't the one which I set in the vncserver@:3.service file located in /lib/systemd/system/ directory. The content of the mention file: ---------------------------------------- [Unit] Description=Remote desktop service (VNC)...

Hi Patrick, Thanks for you quickly answer. Yes, x11vnc was installed on my system. The problem is i not understand the ?logic" of vnc connection, so i try to dark? I copy the /etc/systemd/system/vncserver@:1.service to /etc/systemd/system/vncserver@:0.service restart the vnc service and obtain Jul 18 11:17:16 systemd[1]: vncserver@:0.service: control process exited, code=exited status=98 Jul 18 11:17:16 systemd[1]: Failed to start Remote desktop service (VNC). Jul 18 11:17:16 systemd[1]: Unit vncs...

I am trying to get a remote screen on C7. I did the following on C7 server: yum install tigervnc-server cp /lib/systemd/system/vncserver at .service /etc/systemd/system/vncserver@:1.service systemctl daemon-reload edit /etc/systemd/system/vncserver@:1.service and replace <USER> with myuser su - myuser run vncpassword to set password systemctl start vncserver@:1.se...

Hello, I just installed CentOS 4.4 and when I connect to it from my XP machine using Cygwin/X and the gnome desktop I've noticed that after a couple of minutes it slows to a crawl (menus and dialog boxes don't display immediately when I click on them). Accessing the X session from the console does not exhibit this behavior. Just recently, instead of going with the default gnome

hi all, I've inherited a server with CentOS 6.4 the VNC Server starts up with the OS and its screen resolution is set to 800x600. I found that I can set the resolution by specifying the -geometry switch, but I can't find where the call to start the vncserver is set in order to change it. I know that it's not in /etc/xinetd.d (the only file there is rsync) here are the contents of ~/.vnc/xstartup #!/bin/sh [ -r /etc/sysconfig/i18n ] && . /etc/sysconfig/i18n export LANG export SYSFONT vncconfig -iconic & unset SESSION_MANAGER unset...

...centos.org/HowTos/VNC-Server I can telnet to port 5901 from the machine itself: # telnet 127.0.0.1 5901 Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. RFB 003.008 But, when I try to connect to it from the outside world, I get a connection timeout. My /etc/sysconfig/vncservers file does not have the -nolisten tcp nor the -localhost options so it should be configured to accept outside connections. Is there some default setting in the vncserver that I need to change to allow outside connections? Thanks, Neil -- Neil Aggarwal, (972)834-1565, http://UnmeteredVPS.net/ce...

> Is the port opened in the firewall? I stopped firewalld with "systemctl stop firewalld" Jerry On Fri, Apr 3, 2015 at 2:46 PM, Jerry Geis <geisj at pagestation.com> wrote: > I am trying to setup a centos 7.1 vncserver > > I cannot believe they went from a relatively easy process in 6 to the > "crazyness" that is 7. > > I did the following: > yum install tigervnc-server > cp /lib/systemd/system/vncserver at .service > /etc/systemd/system >...

Is there a way to make vncserver on centos 7 to be read only? I want to allow someone to connect and see the screen- but not change it of course. Thanks, jerry

Hi, Does anyone know if possible to get vncserver to only listen on one particular Ip address? Have two network interfaces (public + private) and just want the vncserver to listen on the private IP address 192.168.10 for example Thanks Keith

Hello everyone, Following the directions I found here: http://wiki.centos.org/HowTos/VNC-Server I get to part 2.4, and when I start the vncservice, I get this error message: Starting VNC server: 1:blah Invalid null command. if: Expression Syntax. A VNC server is already running as :1 else: endif not found. [FAILED] If I stop it, and

Hi all, I have Xen 3.0.3 installed on Debian Etch 4.0. The problem I have with it is that vncservers are not run for guest domains (also Etch), nomatter I specify vfb = [ ''type=vnc'' ], or not. Does Xen 3.0.3 support vnc frame buffers, or do I have to upgrade Xen? I know that Xen 3.1 creates vncservers with no problems. Thanks _______________________________________________ Xe...