search for: unicall

...with one E1, it works fine; I receive DNIS and ANI for making calls and answering calls. ? When I start the Asterisk I receive call from outside correctly including DNIS and ANI, and receive the following messages: ? Sep? 7 10:29:59 WARNING[12167]: Answer Call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5) Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Answer call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 0101? ->????? [1/????? 20/Group B?????? /Accepted Paid] Sep? 7 10:29:59 WARNING[12167]: Unicall/2 event Answered Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Channe...

Hi all, I have begun the release of my MFC/R2 protocol software. At http://www.opencall.org/installing-mfcr2.html there are instructions for installing what I have released so far. This is the MFC/R2 protocol software, and a test program. The software to interface Asterisk to the MFC/R2 code will be released shortly. It used to work, but it hasn't been touched for a while, and Asterisk

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the...

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DE...

Hi, executing the reload command on Asterisk make the Unicall channel unblock all Unicall channels dropping active calls. Is this just a local error (maybe in the other end of my E1 ?), an option in the source (maybe a debugging option ?) or it must be this way ? Asterisk: 1.0.9 unicall: 0.0.3-pre4 protocolvariant: br Thanks, Leonardo Aug 31 15:00...

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WA...

...the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier claims but they too have logs to counter my claim. So, I hope people, please give me a good insight and direction to resolve this problem. I have the following for my R2 box: unicall-0.0.3pre8 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 spandsp-0.0.2pre25 asterisk-1.2.6 zaptel-1.2.5 wanpipe-2.3.3-2 2.6.11-1.1369_FC4smp sangoma A101 in my zaptel.conf I got the following: span=1,0,0,cas,hdb3 loadzone = us defaultzone=us cas=1-15:1101 cas=17-31:1101 in my unicall.co...

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10 (successfull) Aug 17 13:25:38 WARNING[2195...

...alls to the telco.. but I can't receive any calls from the pbx. When receive a call from the pbx I get this: cause 32771 - T3 timed out If I connect the pbx directly to the telco there is no problem, the calls are stablished correctly. Im using the package at: http://www.moythreads.com/astunicall/downloads/ http://www.moythreads.com/astunicall/files/astunicall-1.2.25-0.1.tar.gz that contains: asterisk-1.2.25 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.2.22 My zaptel.conf is this: loadzone=mx defaultzone=mx span=1,1,0,cas,hdb3...

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or congest...

Hello All. I'm using sangoma card A-101. tested successful with E10 (ACATEL) Exchange, connection with E1, CAS, (using unicall-0.0.3pre4). my system run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10 (successfull) Aug 17 13:25:38 WARNING[2195...

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and ou...

Hi all, any body can tell me why i am receiving this message in my sever ? I have running * with 10 Digital Lines, but i am receiving a lot of times this message . Is a software issue or is a hardware issue ? Regards. Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:2672 handle_uc_event: Unicall/5 event Alarm Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:3091 handle_uc_event: Unicall/5 Alarm masks 0x0000 0x0004 Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:3096 handle_uc_event: Unicall/5 Alarm No Alarm raised, Yellow Alarm cleared Mar 27 12:58:24 WARNING[258...

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com> ======================================================================== = Connected to As...

...at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the Asterisk i get at the Nortel only a empty sound, and after about 15 o 20 sec it's hangup. Any suggestion ? The log at Asterisk is: Aug 27 09:16:20 WARNING[6496]: chan_unicall.c:704 unicall_report: MFC/R2 UniCall/30 <- 0001 [1/ 1/Idle /Idle ] Aug 27 09:16:20 WARNING[6496]: chan_unicall.c:704 unicall_report: MFC/R2 UniCall/30 Detected Aug 27 09:16:20 WARNING[6496]: chan_unicall.c:704 unicall_report: MFC/R2 UniCall/30 Making a new call with CRN 327...

I have a customer that is complaining that any call coming in from Nextel gives a fast busy. We are running Asterisk 1.4.7.1 with Zaptel 1.4.3 and all the MFC/R2 patches and libraries. All other calls go out and come in, just Nextel seems to have this problem. The phone company technician connected a PBX emulator on the line and that one could receive the calls from Nextel. The E1 is provided

...at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the Asterisk i get at the Nortel only a empty sound, and after about 15 o 20 sec it's hangup. Any suggestion ? The log at Asterisk is: Aug 27 09:16:20 WARNING[6496]: chan_unicall.c:704 unicall_report: MFC/R2 UniCall/30 <- 0001 [1/ 1/Idle /Idle ] Aug 27 09:16:20 WARNING[6496]: chan_unicall.c:704 unicall_report: MFC/R2 UniCall/30 Detected Aug 27 09:16:20 WARNING[6496]: chan_unicall.c:704 unicall_report: MFC/R2 UniCall/30 Making a new call with...

...2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get funky, some calls from some phones get trough and some don't. Besides that, when I put the loglevel parameter in unicall.conf, asterisk gives me a seg fault when loading the module. The last problem is that when I try the "reload" command on the asterisk CLI, the E1s get blocked again because chan_unicall.so fails to reload. First of all, lets start with my environment: Linux version:...

...;t find where is define the end DNIS signal is define. Actually the libmfcr2 send a ONE (1) at the end of sending all the DNIS numbers. I need to send a TWO (2), this becouse in Mexico the normal is to send a 2 at the end, not a ONE. In the next example i dialed un 6 19:12:17 WARNING[719] chan_unicall.c: MFC/R2 UniCall/5 Call control(1) Jun 6 19:12:17 WARNING[719] chan_unicall.c: MFC/R2 UniCall/5 Make call Jun 6 19:12:17 WARNING[719] chan_unicall.c: MFC/R2 UniCall/5 Making a new call with CRN 32770 Jun 6 19:12:17 WARNING[719] chan_unicall.c: MFC/R2 UniCall/5 0001 -> [1/ 1/Idle...

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and DNIS digits, except for International incoming call. My phone provider(...