search for: uhhuh

Nov 12 08:54:27 steerpike kernel: Uhhuh. NMI received for unknown reason a0 on CPU 0. Nov 12 08:54:27 steerpike kernel: You have some hardware problem, likely on the PCI bus. Nov 12 08:54:27 steerpike kernel: Dazed and confused, but trying to continue Would my Digium TDM410P cause an NMI, or is my computer failing? - Mike

...CVS zaptel from 2004-12-17, and the TDM04b card. Snippet of syslog as follows: Dec 19 15:33:17 nisui kernel: Freshmaker version: 71 Dec 19 15:33:17 nisui kernel: Freshmaker passed register test Dec 19 15:33:18 nisui kernel: Module 0: Installed -- AUTO FXO (FCC mode) Dec 19 15:33:18 nisui kernel: Uhhuh. NMI received for unknown reason 31 on CPU 0. Dec 19 15:33:18 nisui kernel: Dazed and confused, but trying to continue Dec 19 15:33:18 nisui kernel: Do you have a strange power saving mode enabled? Dec 19 15:33:18 nisui kernel: Module 1: Installed -- AUTO FXO (FCC mode) Dec 19 15:33:18 nisui kernel...

...up completely, requiring a power cycle to get it running again. After the power cycle, if I look in /var/log/messages I see a long cycle of the following messages before reboot: kernel: Dazed and confused, but trying to continue kernel: Do you have a strnage power saving mode enabled? kernel: Uhhuh, NMI received for unknown reason 20 on CPU 0 4. if I cat /proc/interrupts, I don't see any entry for a wcfxo module. In any case, I did follow the setup instructions on the Digium site (make install in /usr/src/zaptel, edit /etc/zaptel.conf, edit /etc/asterisk/zapata.conf, etc.) and we curre...

...ly reboot? I''m running memtest now, and will run memtest86 once I am back in the office. James eth2: Promiscuous mode enabled. eth2: Promiscuous mode enabled. br2: port 1(eth2) entering learning state br2: port 1(eth2) entering forwarding state br2: topology change detected, propagating Uhhuh. NMI received. Dazed and confused, but trying to continue You probably have a hardware problem with your RAM chips TLAN: eth0: Adaptor Error = 0x180002 TLAN: eth0: Starting autonegotiation. TLAN: eth0: Autonegotiation complete. TLAN: eth0: Link active with AutoNegotiation enabled, at 100Mbps Full-...

...kernel panic while using digium cards. It may be related to IRQ shared. Can this cause a lot of drop call and bad voice quality ? Do you guys know if there is a way I can assign one IRQ for each digium card ? Thanks a lot. Here is the output of /var/log/syslog kernel: [ 3821.982893] Uhhuh. NMI received for unknown reason 20. kernel: [ 3821.982938] Do you have a strange power saving mode enabled? kernel: [ 3821.982964] Dazed and confused, but trying to continue dahdi_hardware pci:0000:04:08.0 wct4xxp+ d161:0420 Wildcard TE420 (4th Gen) pci:0000:06:08.0 wct4xxp+...

...an issue that I would like to record: I upgraded both DL580s to Centos 4.7 via yum but only rebooted one initially- this node, previously bomb-proof, started to hang randomly with no obvious messages logged to help with diagnosis. In the dmessage output I found this sequence never seem before Uhhuh. NMI received for unknown reason 20. Dazed and confused, but trying to continue Do you have a strange power saving mode enabled? Uhhuh. NMI received for unknown reason 30. Dazed and confused, but trying to continue (repeated several times) Googling revealed many different scenarios with this boot...

...ipsupply.com] > I see that there is a lot of discussion on the web about a > common error > after installing and modprobe'ing the zaptel driver. However I don't > see any resolution, anyone found a solution? > > Here's the output I get after modprobe: > > Uhhuh. NMI received. Dazed and confused, but trying to continue > You probably have a hardware problem with your RAM chips > Module 0: Installed -- AUTO FXO (FCC mode) > Module 1: Installed -- AUTO FXO (FCC mode) > Module 2: Installed -- AUTO FXO (FCC mode) > Module 3: Installed -- AUTO FX...

...: 24 FALC version: 00000000 TE110P: Setting up global serial parameters for E1 FALC V1.2 TE110P: Successfully initialized serial bus for card Found a Wildcard: Digium Wildcard TE110P T1/E1 Freshmaker version: 71 Freshmaker passed register test Uhhuh. NMI received. Dazed and confused, but trying to continue You probably have a hardware problem with your RAM chips Module 0: Installed -- AUTO FXS/DPO Module 1: Not installed Module 2: Not installed Module 3: Installed -- AUTO FXO (FCC mode) Found a W...

Recently I started getting weird errors. All of a sudden I see the harddrive of my box glowing steadily and syslog is getting filled (and the cpu hogged) with these errors: It seems to start with this line: Jan 1 03:28:04 kernel: FXO PCI Master abort Jan 1 03:28:04 last message repeated 12 times Jan 1 03:28:06 kernel: CI Master abort Jan 1 03:28:06 kernel: FXO PCI Master abort and seems to

...I-6221) in a windows XP HVM. Device is recognized under XP and look functionnal until I try to use it. If I try to acquire data or generate a signal (with National Instrument official tools) nothing happen on the card (no signal) and linux kernel start flooding me with this error message : kernel: Uhhuh. NMI received. Dazed and confused, but trying to continue kernel: You probably have a hardware problem with your RAM chips I tried another RAM module but no changes. If I insist my host computer freeze and reboot (if xen watchdog is activated) Something strange in xm dmesg : (XEN) mm.c:676:d0 Non...

G'day, I am testing a new server with a Supermicro X7SBA motherboard and TE405 cards. When I load Dahdi and run dahdi_cfg I get the following errors: kernel: Uhhuh, NMI received for unknown reason b1 on CPU 0 You probably have a hardware problem with your RAM chips Dazed and confused, but trying to continue The reason codes I have seen are a0, a1, and b1. The problem only occurs once and the system seems to work fine after th...

...han fight with it, I just decided to reload it. It was running 5.3, and it is now running 5.4. However, when I go to boot it gets stuck at starting udev. If I let it sit long enough it will then give me errors with something along the lines of: Dazed and confused, but trying to continue Uhhuh. NMI received for unknown reason 00 Do you have a strange power saving mode enabled? Wondering if anyone has an idea.. Thanks, Ryan

...Found a Wildcard: Wildcard TE410P-Xilinx Mar 22 00:33:48 VoiceOne kernel: Registered tone zone 0 (United States / North America) Mar 22 00:33:48 VoiceOne kernel: TE410P: Span 1 configured for CCS/HDB3/CRC4 Mar 22 00:33:48 VoiceOne kernel: SPAN 1: Primary Sync Source Mar 22 00:33:48 VoiceOne kernel: Uhhuh. NMI received for unknown reason 20. Mar 22 00:33:48 VoiceOne kernel: Dazed and confused, but trying to continue Mar 22 00:33:48 VoiceOne kernel: Do you have a strange power saving mode enabled? Mar 22 00:33:48 VoiceOne kernel: TE410P: Span 2 configured for CCS/HDB3/CRC4 Mar 22 00:33:48 VoiceOne ke...

HI all, I have the following setup running: EP<--->Calling Asterisk<--->Relaying Asterisk<--->Softswitch<---> PSTN The Endpoint EP is registered with the Calling Asterisk. Calls are forwarded from this machine to Relaying Asterisk which in turn forwards it to the Softswitch. In addition, this machine also relays back responses from the Softswitch to the Calling

...has the Ambient chip on it) > > All I get is: > > FXO PCI Master abort errors. > > Depending on the way it feels, either these are repeated till > /var/log/ is full, or I get one and then the thing hangs. > This may, or may not, have something to do with a message > > Uhhuh. NMI received. Dazed and confused, but trying to continue > You probably have a hardware problem with your RAM chips > > I have tried all combinations of > Debian builds of Linux 2.4.27, 2.6.8 and 2.6.11 > Debian builds of Zaptel > CVS builds of Zaptel > > I have tried it on...

...veau I get the following message if I run startx from runlevel 3 Fatal server error: DMA queue hang: dmaPut=1ffc, current=0, status=0 giving up. Running 'telinit 5' to start GDM gives me a messed up display and a few X crashes before I get the following messages from the kernel: Uhhuh. NMI received for unknown reason a1. You have some hardware problem, likely on the PCI bus. Dazed and confused, but trying to continue And then the system either locks or, occasionally, reboots itself. Fun! -- Configure bugmail: http://bugs.freedesktop.org/userprefs.cgi?tab=email ------- Yo...

Hi all, So I'm trying to work on this complex fax server setup, and part of it involves connecting my asterisk server to my Rolm CBX switch, via a T1 line. I plan on using Asterisk simply as a T1-PRI Bridge to IAXmodem (which in turn, activates HylaFax+ to handle the faxing). So far, though, I don't think I'm getting 100% of the way there. When dialing the fax extension from my

...In 1 minute my box crashes Rebooting the box and running it again, same thing. /var/log/messages before crash Dec 10 17:24:30 conference kernel: Zapata Telephony Interface Registered on major 196 Dec 10 18:36:03 conference kernel: wcfxo: DAA mode is 'FCC' Dec 10 18:36:03 conference kernel: Uhhuh. NMI received for unknown reason 15 on CPU 0. Dec 10 18:36:03 conference kernel: Dazed and confused, but trying to continue Dec 10 18:36:03 conference kernel: Do you have a strange power saving mode enabled? Dec 10 18:36:03 conference kernel: Found a Wildcard FXO: Generic Clone Dec 10 17:24:33 conf...

Hi all, I would like to discuss a design idea I have in mind with you, in order to get critical feedback. ActiveRecord supports single table inheritance(STI) "per se", BUT you must add all possible instance variables(properties) of all subclasses to the "base table"(as columns). I would like to circumvent this restriction. Say we have a class AbstractGenericThing <