search for: tuxtechnologies

I have a doubt. If you use such a script monitoring the link status with ping and then reconfiguring, why do you need the DGD patch? You need to do some reconfiguration (change multipath to a single default route) anyway if you use the script, right? Also, the DGD patch uses src to lookup the routing table entry, but if you have a dynamic IP for the WAN interface (PPPoE, DHCP etc), this approach

Hello! I read the Split access and Load balancing sections into LARTC (Chapter 4). However I have one gateway only and the LARTC says about 2 links. I need to know how to make a load balance with my links. Thanks in advance. Eriberto - Brazil

hello i have slackware installed and i have two internet connections , ADSL(2,5mbps) + CableModem(1mbps) i want to share the connections in a small network NAT for the ADSL connection, and a proxy server for the cablemodem connection i searched all over the internet (probably not where i was supposed to) but i could''n find a solution if someone could give me a tip i would really

Hello all! I applied http://www.ssi.bg/~ja/routes-2.6.8-10.diff patch to kernel 2.6.8.1 and it works fine, or almost fine. It does the load balancing well, but when one link is dropped it continues to try it. At the end of http://www.ssi.bg/~ja/nano.txt it is said to ping gateway 1 and gateway 2, for the kernel to know if that route is working, but since my linux is connected to the links

Hello, On the Intel Core 2 Duo processor based systems, we have the option of installing either x86_64 or the i386 distribution. I would like to know your experiences with the x86_64 port. How does it compare with the i386 distribution in terms of stability, reliability and performance ? How significant are the performance benefits gained by using the x86_64 linux instead of i386 on the same

Has anyone created or rebuilt a Linux Software RAID having mirrored partitions on unequal sized hard disks ? There is a CentOS 5 server having two 400 GB hard disks with five mirrored partitions (software RAID 1) and one of the hard disks is dying. Since new 400 GB HDDs are not available here, we are exploring the possibility of replacing the faulty hard disk with one of a higher capacity (500 GB

Hi all! After that good thread "DGD patch not detecting dead gateway" I was able to set up a Load Balancing with ping based DGD (without Julian Anastasov patch). But now I''m facing a new problem and tried some options, with only partial solutions. I made a script based on http://www.mail-archive.com/lartc@mailman.ds9a.nl/msg16257.html (Thank you Manish Kathuria),

I got file conflicts between the sysreport and sos packages on the file /usr/sbin/sysreport. I unchecked sysreport in the package updater UI and the rest of the update is proceedng.

Hi I need informmation about this Topic: Load balancing,, I have 2 nic to internet, 1 nic to DMZ, and 1 nic to LAN, but I don,t know how do that. Where I can found information ?? Thx!! For your information! -- Este mensaje ha sido analizado por MailScanner en busca de virus y otros contenidos peligrosos, y se considera que est? limpio. For all your IT

Hello, Is there any command / option available on CentOS to expire a user's password immediately ? I remember using "passwd -e" on some other distribution but the -e option does not seem to be present on CentOS 5.x. Thanks, Manish

...of a distribution like RHEL 4 or RHEL 5, Red Hat would stick to the same major and minor number of the kernel and would just change release numbers. What is the relation, if any, between the new kernels and the updates released by Red Hat ? Thanks, -- Manish Kathuria Tux Technologies http://www.tuxtechnologies.co.in/

Hello, Does CentOS 5.4 support large ( > 2 TB) external storage devices using GPT (GUID Partition Tables), while the main OS resides on smaller hard disks using MBR. In this scenario, what can be the largest possible size of an ext3 partition (and filesystem) which can be created on the storage array under CentOS 5.4 ? Thanks, Manish

I have recently installed CentOS 6 on a system with a Realtek 8180L wireless card. The wireless card is detected properly and uses the rtl8180 driver. But it connects to our wireless network only after logging to the Desktop Environment (GNOME) and using the Network Manager Applet. In order to make the wireless card connect to the network automatically at system start up, I edited the Connection

I want to configure a device with three network interfaces where two of them would bridge two segments of the LAN subnet and the third one would be connected to the WAN link. eth0 - 10.10.10.2/24 to be connected to the internet gateway having IP 10.10.10.1/24 (also the default gateway for the device) eth1 and eth2 bridged as br0 with IP address 172.16.100.1 connected to different segments of the

hi all, first i wann to explain my network & it''s problem, i am using a redhat el5 for multigateway routing, i have 3 adsl lines which is connected with eth0, eth2 and eth3. eth1 is my local network. those 3 lines comes with adsl modem from same isp with equal bandwidth (512 Kbps). In this adsl modems there is one lan and one wan port, adsl modem''s lan ip is gateway for my

Are the RPMs for the latest GFS kernel module GFS-kernel-2.6.9-72.2.0.8 to be used with the version 2.6.9-55.0.9.EL available ? I tried to compile the Source RPMs available from the Red Hat site but the modules can't be loaded because of invalid module format arising from version magic issues. The syslog shows: node0 kernel: gfs: version magic '2.6.9-55.0.9.ELsmp SMP 686 REGPARM

Hello, I had installed CentOS 5.0 on my desktop PC having a Realtek 8180L based PCI wireless card. Since the drivers for this chip are not available in the kernel, I created RPMs for ndiswrapper-1.43 from the source code and installed them. I could configure the wireless card and use it but invariably the system freezes after sometime. No such thing happens if the wireless card is disabled. In

What is the maximum number of nameservers mentioned in /etc/resolv.conf which will be queried while looking up a hostname or IP address in the present version ? Earlier implementations had a ceiling of 3 name servers which could be queried. Has there been any increase ? Thanks, Manish

I am facing problems assigning the owner and group to an ext3 filesystem being mounted from an external storage. I created a mount point /vol and changed its owner and group to alpha and beta respectively (as required). The ext3 filesystem (LV from the external storage) was then mounted on /vol using the mount command. However, after mounting the filesystem the owner and group of /vol changed