search for: ttys5

...pport MMIO? If I look in /proc/ioports, I see my on-board serial port listed, but nothing about the PCIe add-in card. dmesg output shows: [ 13.972625] ttyS4: detected caps 00000700 should be 00000100 [ 13.972632] 0000:04:00.0: ttyS4 at MMIO 0xdf1fd000 (irq = 16) is a 16C950/954 [ 13.972743] ttyS5: detected caps 00000700 should be 00000100 [ 13.972750] 0000:04:00.0: ttyS5 at MMIO 0xdf1fd200 (irq = 16) is a 16C950/954 [ 13.972849] ttyS6: detected caps 00000700 should be 00000100 [ 13.972856] 0000:04:00.0: ttyS6 at MMIO 0xdf1fd400 (irq = 16) is a 16C950/954 [ 13.972952] ttyS7: detected...

Can someone please help me with writing a udev rule? I need /dev/ttyUSB0 to automatically have 777 rights when plugged in. I'd like it to only apply to that one specific device. I'm not sure where to start, what files to look at and also what to write to make it work. TIA Brad This e-mail transmission contains information that is confidential and may be privileged. It is intended only

...UX at zytor.com Sent: Thursday, November 9, 2006 4:58:50 PM Subject: [syslinux] Serial with syslinux. Can syslinux be upgraded to support more then 4 serial ports? Could syslinux be configured to auto probe for the first serial port? Ubuntu 6.6.1 boots and can find the card at port ttyS4 and ttyS5. Voyage (debian) linux reset the pci serial card and assigns it to ttyS0 and ttyS1 A few weeks back I asked about a boot loader with ttyUSB support. It was pointed out that a USBserial stack would be very bloated. So I purchased a pci serial IO card. ON boot up the card is configured...

...0 (Uart) 0a:0c.1 Bridge: Oxford Semiconductor Ltd OX16PCI954 (Quad 16950 UART) function 1 (8bit bus) However, only the 4 serial ports on one of the two cards are configured correctly: # dmesg | fgrep ttyS ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS4 at I/O 0x5020 (irq = 177) is a 16C950/954 ttyS5 at I/O 0x5028 (irq = 177) is a 16C950/954 ttyS6 at I/O 0x5030 (irq = 177) is a 16C950/954 ttyS7 at I/O 0x5038 (irq = 177) is a 16C950/954 ttyS1 at I/O 0x5060 (irq = 193) is a 16450 ttyS2 at I/O 0x5068 (irq = 193) is a 16450 ttyS3 at I/O 0x5070 (irq = 193) is a 16450 I have no idea what ttyS1-3 are...

...i686]) dmesg says: Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 16 (level, low) -> IRQ 233 ttyS4 at I/O 0xd080 (irq = 233) is a 16550A ttyS5 at I/O 0xd000 (irq = 233) is a 16550A ACPI: PCI Interrupt 0000:01:0a.1[A] -> GSI 16 (level, low) -> IRQ 233 ttyS6 at I/O 0xcc00 (irq = 233) is a 16550A ttyS7 at I/O 0xc880 (irq = 233) is a 16550A With the 64-bit kernel (2.6.18-164.el5 [x86_64]) I get: Serial: 8250/16550 driver $Revision: 1....

I've already read through bug 11811 (http://bugs.winehq.org/show_bug.cgi?id=11811) so I know a patch was offered about two years ago for Wine automatically recognizing the com* symlinks in ~/.wine/dosdevices. Is there any hope that this will be functional soon? I am trying a utility that needs to access the serial ports but there are none shown available in its ports dialog. I do have

...gives: network socket network http network ipp network lpd direct parallel:/dev/lp0 direct scsi serial serial:/dev/ttyS0?baud=115200 serial serial:/dev/ttyS1?baud=115200 serial serial:/dev/ttyS2?baud=115200 serial serial:/dev/ttyS3?baud=115200 serial serial:/dev/ttyS4?baud=115200 serial serial:/dev/ttyS5?baud=115200 serial serial:/dev/ttyS6?baud=115200 ----------------------------------------------- serial serial:/dev/ttyS29?baud=115200 serial serial:/dev/ttyS30?baud=115200 serial serial:/dev/ttyS31?baud=115200 direct usb:/dev/usb/lp0 direct usb:/dev/usb/lp1 direct usb:/dev/usb/lp2 no network smb -...

Hi Not entirely centos related but that what the boxes are running so here i go ;) 2 of our centos boxes run nagios for network monitoring and send email and paging alerts and are connected to standard phone lines using modems to send the pages. I'm looking for a way in the event of provider failure to login to these machines and so am looking at the ability to connect to the console over

I have been investigating pci pass-through for virtualized guests and the documentation I have found seems to me to lack a certain consistency in its example. This may be due to my not understanding what it is trying to inform me. What I wish to do is to configure a pci multi-port serial i/o card for use by a single virtual host. I start by running lspci -v on the host to identify the serial

Unfortunately, almost all the Windows programs I want to run under Wine need to access the COM: ports, and I cannot get any of them to run. Typically, I get stuff like this ... fixme:comm:EscapeCommFunction16 no cid=0 found! fixme:comm:EscapeCommFunction16 no cid=0 found! err:comm:COMM16_ReadComplete async read failed 000003e3 fixme:comm:EscapeCommFunction16 no cid=3 found!

...0 0 4, 92 Dec 11 21:57 ttyS28 crw------- 1 0 0 4, 93 Dec 11 21:57 ttyS29 crw------- 1 0 0 4, 67 Dec 11 21:57 ttyS3 crw------- 1 0 0 4, 94 Dec 11 21:57 ttyS30 crw------- 1 0 0 4, 95 Dec 11 21:57 ttyS31 crw------- 1 0 0 4, 68 Dec 11 21:57 ttyS4 crw------- 1 0 0 4, 69 Dec 11 21:57 ttyS5 crw------- 1 0 0 4, 70 Dec 11 21:57 ttyS6 crw------- 1 0 0 4, 71 Dec 11 21:57 ttyS7 crw------- 1 0 0 4, 72 Dec 11 21:57 ttyS8 crw------- 1 0 0 4, 73 Dec 11 21:57 ttyS9 crw------- 1 0 0 5, 3 Dec 11 21:57 ttyprintk crw------T 1 0 0 10, 239 Dec 11 21:57 uhid crw-r----- 1 0 0 10, 223...

...-- 1 0 0 4, 92 Feb 27 02:31 ttyS28 ------- 1 0 0 4, 93 Feb 27 02:31 ttyS29 crw------- 1 0 0 4, 67 Feb 27 02:31 ttyS3 crw------- 1 0 0 4, 94 Feb 27 02:31 ttyS30 crw------- 1 0 0 4, 95 Feb 27 02:31 ttyS31 crw------- 1 0 0 4, 68 Feb 27 02:31 ttyS4 crw------- 1 0 0 4, 69 Feb 27 02:31 ttyS5 cr------- 1 0 0 4, 70 Feb 27 02:31 ttyS6 crw------- 1 0 0 4, 71 Feb 27 02:31 ttyS7 crw------- 1 0 0 4, 72 Feb 27 02:31 ttyS8 crw------- 1 0 0 4, 73 Feb 27 02:31 ttyS9 crw------- 1 0 0 5, 3 Feb 27 02:31 ttyprintk crw------- 1 0 0 10, 239 Feb 27 02:31 uhid cr----- 1 0 0 10, 223 Feb 27...

On Sun, Mar 23, 2014 at 12:26:28PM +0000, Richard W.M. Jones wrote: > Secondly, we should be able to inspect all Linux guests, including > Tiny Core Linux, but it looks like in this case it is failing. This > is a bug. I had a look at how the Tiny Core Linux ISO is arranged. It loads the main operating system root partition as a single large initramfs, with optional modules loaded

...0 0 4, 92 Nov 26 12:02 ttyS28 crw------- 1 0 0 4, 93 Nov 26 12:02 ttyS29 crw------- 1 0 0 4, 67 Nov 26 12:02 ttyS3 crw------- 1 0 0 4, 94 Nov 26 12:02 ttyS30 crw------- 1 0 0 4, 95 Nov 26 12:02 ttyS31 crw------- 1 0 0 4, 68 Nov 26 12:02 ttyS4 crw------- 1 0 0 4, 69 Nov 26 12:02 ttyS5 crw------- 1 0 0 4, 70 Nov 26 12:02 ttyS6 crw------- 1 0 0 4, 71 Nov 26 12:02 ttyS7 crw------- 1 0 0 4, 72 Nov 26 12:02 ttyS8 crw------- 1 0 0 4, 73 Nov 26 12:02 ttyS9 crw------- 1 0 0 5, 3 Nov 26 12:02 ttyprintk crw------- 1 0 0 10, 239 Nov 26 12:02 uhid crw------- 1 0 0 10, 223...

The options -x -v gave me an error that no such option so I ruined it with —debug option. root@ny2proxd03:/var/lib/vz/images/100# virt-resize --expand /dev/sda3 vm-100-disk-1.qcow2 vm-100-disk-1.qcow2.resized --debug command line: virt-resize --expand /dev/sda3 vm-100-disk-1.qcow2 vm-100-disk-1.qcow2.resized --debug Examining vm-100-disk-1.qcow2 ... libguestfs: trace: add_drive

...- 1 0 0 3, 47 Sep 9 17:19 ttyrf crw------- 1 0 0 3, 48 Sep 9 17:19 ttys0 crw------- 1 0 0 3, 49 Sep 9 17:19 ttys1 crw------- 1 0 0 3, 50 Sep 9 17:19 ttys2 crw------- 1 0 0 3, 51 Sep 9 17:19 ttys3 crw------- 1 0 0 3, 52 Sep 9 17:19 ttys4 crw------- 1 0 0 3, 53 Sep 9 17:19 ttys5 crw------- 1 0 0 3, 54 Sep 9 17:19 ttys6 crw------- 1 0 0 3, 55 Sep 9 17:19 ttys7 crw------- 1 0 0 3, 56 Sep 9 17:19 ttys8 crw------- 1 0 0 3, 57 Sep 9 17:19 ttys9 crw------- 1 0 0 3, 58 Sep 9 17:19 ttysa crw------- 1 0 0 3, 59 Sep 9 17:19 ttysb crw------- 1 0 0 3, 60 Sep...

Hello, I've found a problem running libguestfs on my system. The system has /var mounted with a symbolic link to /mnt/bigdata/var root@red1:/var/log/nova# ls -ld /mnt/bigdata/var drwxrwxr-x 15 root users 4096 jul 7 17:55 /mnt/bigdata/var root@red1:/var/log/nova# ls -ld /var lrwxrwxrwx 1 root root 16 oct 30 2012 /var -> /mnt/bigdata/var Any help here? this is test tool output:

...baud=115200"... D [03/Mar/2004:10:30:44 +0200] LoadDevices: Added device "serial:/dev/ttyS3?baud=115200"... D [03/Mar/2004:10:30:44 +0200] LoadDevices: Added device "serial:/dev/ttyS4?baud=115200"... D [03/Mar/2004:10:30:44 +0200] LoadDevices: Added device "serial:/dev/ttyS5?baud=115200"... D [03/Mar/2004:10:30:44 +0200] LoadDevices: Added device "serial:/dev/ttyS6?baud=115200"... D [03/Mar/2004:10:30:44 +0200] LoadDevices: Added device "serial:/dev/ttyS7?baud=115200"... D [03/Mar/2004:10:30:44 +0200] LoadDevices: Added device "serial:/dev...