search for: tor2

I just received my dev kit and installed the hardware. I followed the directions Digium sends out to the letter and when I ran modprobe tor2 I got the following error: /lib/modules/2.4.18-19.7.x/misc/tor2.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.18-19.7.x...

Hi list, I have a asterisk box with an E400P that was running ok until last week. The machine just stop responding and after a reboot, the module (tor2) doesn't load anymore. anyone could help? regards Eduardo modprobe returns this: asterix:~# modprobe tor2 Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfe121800/0xfe121000 irq 7 Did not get DONE signal. Short file maybe?? Registered Torm...

...nal) Kernel: 2.6.18-53.1.13.el5 All yum updates applied. Zaptel 1.4.8 compiles with no errors or warnings. Problem: When I reboot the server, the machine crashes (hard down) with a kernel panic right as the console says "Starting udev:". I go in with the rescue disk, delete the tor2.ko file, and it will boot fine. I do a "make install" again with 1.4.8 and when rebooting the machine locks up again - kernel panic. The panic message has a lot of stuff that I don't understand, a lot of which scrolls off the screen, but I do notice it mentions the "tor2"...

...-edge rtc 14: 38259 IO-APIC-edge ide0 15: 12 IO-APIC-edge ide1 16: 0 IO-APIC-level usb-uhci, usb-uhci 17: 0 IO-APIC-level Intel ICH5 18: 0 IO-APIC-level usb-uhci 19: 0 IO-APIC-level usb-uhci 22: 2700297 IO-APIC-level tor2 23: 14842 IO-APIC-level ehci_hcd, eth0 NMI: 0 LOC: 277453 ERR: 0 MIS: 0 ##### E1 connected to the carrier ####### asterisk-test:/# cat /proc/zaptel/1 Span 1: Tor2/0/1 "Tormenta 2 (PCI) Quad E1 Card 0 Span 1" HDB3/ ClockSource BPV count: 812...

Followed the "instructions" on voip-info.org regardinging fedora FC2, making Zaptel seems to work fine, however when I modprobe I get this. It looks like a version mismatch somehow. Ideas? If this ooc, sorry first post here :-) modprobe tor2 WARNING: Error inserting zaptel (/lib/modules/2.6.5-1.358smp/misc/zaptel.ko): Invalid module format WARNING: Error inserting zaptel (/lib/modules/2.6.5-1.358smp/misc/zaptel.ko): Invalid module format FATAL: Error inserting tor2 (/lib/modules/2.6.5-1.358smp/misc/tor2.ko): Invalid module format FATA...

i have error in install module of tor2. but it compile good. what happen ? ivr2:/usr/src/zaptel # make clean; make install rm -f torisatool makefw tor2fw.h rm -f zttool rm -f *.o ztcfg tzdriver sethdlc rm -f zonedata.lo tonezone.lo libtonezone.so.1.0 *.lo rm -f gendigits tones.h rm -f libtonezone* rm -f tor2ee rm -f core cc -I. -O4...

...ng on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo produces: ZT_SPANCONFIG failed on span 1: Invalid argument (22) /lib/modules/2.4.18-14/misc/wcfxo.o: post-install wcfxo failed /lib/modules/2.4.18-14/misc/wcfxo.o: insmod wcfxo failed ? and modprobe tor2 produces: ZT_SPANCONFIG failed on span 1: Invalid argument (22) /lib/modules/2.4.18-14/misc/tor2.o: post-install tor2 failed /lib/modules/2.4.18-14/misc/tor2.o: insmod tor2 failed ? And nothing works..... ? Now if I remove the E1 configs from zaptel.conf the wcfxo loads, and vice versa.? ? Is ther...

Hi, I have just begun working with TDMoE running between 2 fiber nics the dynamic span works great. In my main asterisk box's startup file I just 'modprobe tor2', then start asterisk. The zaptel, ztdynamic & ztd-eth modules all load by themselves when tor2 is loaded. If I stop asterisk then 'modprobe -r tor2' the tor2 module is removed but the other three remain. If I then 'modprobe -r ztd-eth' it causes a complete lock up on the m...

Greetings, I have a quad port Tormenta 2 PCI card (uses the tor2 driver), which I have been successfully using for some time on an older, power-hungry Intel machine. I recently moved it to a newer machine with an Intel Atom D510 CPU in an effort to save on energy costs, but I cannot seem to get it to work there. Both machines are running Ubuntu 13.10 x64, with...

...usr/src/linux/include -I/usr/src/linux/include/net -DMODVERSIONS -include /usr/src/linux/include/linux/modversions.h -DSTANDALONE_ZAPATA -c zaptel.c cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -DZAPTEL_CONFIG=\"/etc/zaptel.conf\" makefw.c -o makefw ./makefw tormenta2.rbt tor2fw > tor2fw.h Loaded 69900 bytes from file gcc -I/usr/src/linux-2.4/include -O6 -DMODULE -D__KERNEL__ -DEXPORT_SYMTAB -I/usr/src/linux/drivers/net -Wall -I. -Wstrict-prototypes -fomit-frame-pointer -I/usr/src/linux/drivers/net/wan -I /usr/src/linux/include -I/usr/src/linux/include/net -DMODVERS...

I was dropping off junk at the waste transfer station and scarfed a UPS out of the pile of old TV's and VCR's. It was in good physical condition and as I expected, the battery was toast. A new RBC-2 battery restored it to working condition. Then I tried to get it to talk to some software. And I am having no luck. The unit is branded as a Nexxtech Model 6118507 650VA imported into

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help ______________________________________...

Hello everyone, We have an E400P Card from phoniceq.? There is a DAHDI Driver posted at: http://e400p.phoniceq.com/driver/dahdi-tor2-tormenta3-e1.tgz but, it doesn't work.? The author (martin (or marcin) pycko) says that it isn't finished. I've e-mailed martin, and he stated that he would fix the driver AFTER we order 10 more cards, not before.? I have a difficult time ordering thousands of dollars worth of product...

...any other changes in the settings of any device etc, simply loaded and saved). and then did # make dep (modversion.h file was created) I then tried to compile zaptel (zaptel-0.9.1.tar downloaded from ftp site) to get errors (see below) All errors are in the kernel.h (and others) file included in tor2.c I haven't added any digium/other h/w as yet. Could anyone help me fix this please. Regards, Satish Kumar B.G satishkbg@vsnl.net ICODE india pvt ltd Bangalore India ------------- errors ------------------ [root@localhost zaptel-0.9.1]# make clean; make install rm -f torisatool makefw tor2fw....

We use dual Athlon machines with up to three T400P 4-span T1 cards. If I have more than one stick of memory (2 1GB modules or 2 512K modules, each identical), I'm getting a panic soon after I modprobe the tor2 driver. I just loaded the latest from CVS and I'm still getting the panics, which look in part like: Apr 16 14:42:28 test71 kernel: wait_on_irq, CPU 0: Apr 16 14:42:44 test71 kernel: irq: 1 [ 0 1 ] Apr 16 14:42:47 test71 kernel: bh: 0 [ 0 0 ] Apr 16 14:42:47 test71 kernel: Stack dumps: Apr...

...-I/usr/src/linux/drivers/net/wan -I /usr/src/linux/include -I/usr/src/linux/include/net -DMODVERSIONS -include /usr/src/linux-2.4/include/linux/modversions.h -DSTANDALONE_ZAPATA -c zaptel.c cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA makefw.c -o makefw ./makefw tormenta2.rbt tor2fw > tor2fw.h Loaded 69900 bytes from file gcc -I/usr/src/linux-2.4/include -O6 -DMODULE -D__KERNEL__ -DEXPORT_SYMTAB - I/usr/src/linux/drivers/net -Wall -I. -Wstrict-prototypes -fomit-frame-point er -I/usr/src/linux/drivers/net/wan -I /usr/src/linux/include -I/usr/src/linux/include/net -DMODVERS...

...-DMODULE -D__KERNEL__ -DEXPORT_SYMTAB -I/usr/src/linux/drivers/net -Wall -I. -Wstrict-prototypes -fomit-frame-pointer -I/usr/src/linux/drivers/net/wan -I /usr/src/linux/include -I/usr/src/linux/include/net -DMODVERSIONS -include /usr/src/linux-2.4/include/linux/modversions.h -DSTANDALONE_ZAPATA -c tor2.c In file included from tor2.c:30: /usr/src/linux-2.4/include/linux/kernel.h:60: invalid suffix on integer constant /usr/src/linux-2.4/include/linux/kernel.h:60: parse error before numeric constant /usr/src/linux-2.4/include/linux/kernel.h:60: warning: function declaration isn't a prototype /us...

Hi All, I'm having a bit of a time getting my Tormenta 2 card to actually be seen by the system. Whenever I modprobe, the kernel spits out the following (in addition to the "insmod tor2 failed" messages): Invalid Xilinx 8 bit Base resource Registered Tormenta2 PCI Of course, the module says that its registered a Tormenta2 card, but it unloads the driver and frees related resources when it can't get a valid "Xilinx 8 bit Base resource". Heres the pertinent inf...

..._SYMTAB -I/usr/src/linux/drivers/net -Wall -I. > -Wstrict-prototypes -fomit-frame-pointer > -I/usr/src/linux/drivers/net/wan -I /usr/src/linux/include > -I/usr/src/linux/include/net -DMODVERSIONS -include > /usr/src/linux-2.4/include/linux/modversions.h > -DSTANDALONE_ZAPATA -c tor2.c In file included from tor2.c:30: > /usr/src/linux-2.4/include/linux/kernel.h:60: invalid suffix > on integer constant > /usr/src/linux-2.4/include/linux/kernel.h:60: parse error > before numeric constant > /usr/src/linux-2.4/include/linux/kernel.h:60: warning: > function decl...

...similar load test (as with the BOX1) BOX2 was showing 0% idle CPU 70% of the time. Just 3 T1s out of 8. On the load test with just 2 T1s BOX3 was very close to 0% idle on CPU0, CPU1 was at 95% idle. The process ksoftirqd_CPU0 was close to the top of the 'top', with /proc/interrupts showing tor2 related numbers growing very fast. We had 2 T1s plugged into the first T400P board, with nothing going into the second, but the number of interrupts for the both boards was growing at the same pace. Here are the interrupts (after the box reboot, so they are not that big as they were) - do they look...