search for: termtypes

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

hello list i have installed 2 diguim card in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi, I'm having some trouble setting up a Xorcom Bri 4 port. I have compiled asterisk and zaptel using the Bristuff bristuff-0.3.0-PRE-1y-g patches. So I'm running zaptel-1.2.17.1 and asterisk-1.2.18. The problem I'm having is that for one I get no LEDs showing if the unit is in TE and NT mode (not a issue for me but may have some impact on things) I have no errors in any logs I

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

I'm having problems getting an Xorcom USB Bri 4 dialling out in Australia. I can receive calls into the system without an issue, but I can not for the life of me dial out of the system. Below are my configs, I'm hoping its something simple that I just can't see as I've been looking at it for to long. Can any one point me in the right direction. P.S. Yes it is meant to be in TE

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Hi, I have 3 ISDN lines using the digium B410P card. Incoming and outgoing call are working. I use the following version : * libpri-1.4.10.2 * dahdi-2.2.1.1 * asterisk-1.6.2.6 On incoming calls, DTMF is not working, i can't see any logs. Here are the main configuration files : dahdi-channels.conf ;; Span 2: B4/0/1 "B4XXP (PCI) Card 0 Span 1" signalling=bri_cpe

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

Hi All: It appears that the terminfo ansi-m file is no longer distributed with the CentOS 6.2 (along with many others). Can anyone advise how I can obtain this file? As a work around I have copied the file from a CentOS 4 box but that is probably not the "proper" way to do it. TIA Regards, Hugh -- Hugh E Cruickshank, Forward Software, www.forward-software.com

On Sat, Jan 17, 2015 at 09:31:33AM +0100, Bertrand LUPART - Linkeo.com wrote: > >>> However, dahdi_genconf keeps finding no span: > >>> What am i missing? > >> > >> It looks like your driver is loaded correctly. My guess would be maybe > >> the dahdi-tools is packaged as an older version that doesn't know > >> about the newer te435

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

Hi there, we have a problem with dahdi and overlapdial. We are running an E1 in Germany and are in need of overlapdial. The E1 is connected to a Sangoma A101. As soon as overlapdial is set to "yes" we have problems with incoming audio on the dahdi channels. When set to "no" all audio is fine. Basically we can choose between being able to receive calls or to place calls

Hello Team I have installed the new DL580 and used the new TE420B to add capacity on our ivr. Before I put new E1?s I decided to first move the old e1 from the old system to this new one but it has errors which not only affect the audio quality, but also cause the asterisk to refuse any call after sometime even though the channels seems up and active {seems d-channel fails}.. When processing

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS