search for: t4xxp

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

...span=7,7,0,esf,b8zs bchan=145-168 span=8,8,0,esf,b8zs bchan=169-192 span=9,9,0,esf,b8zs bchan=193-216 span=10,10,0,esf,b8zs bchan=217-240 span=11,11,0,esf,b8zs bchan=241-264 span=12,12,0,esf,b8zs bchan=265-288 dahdi_scan : [1] active=yes alarms=OK description=T4XXP (PCI) Card 0 Span 1 name=TE4/0/1 manufacturer=Digium devicetype=Wildcard TE410P (3rd Gen) (VPMOCT128) location=Board ID Switch 0 basechan=1 totchans=24 irq=225 type=digital-T1 syncsrc=1 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=B8ZS,AMI framing_opts=ESF,D4 coding=B8ZS framing=ESF...

...es my zaptel.conf: span=1,0,0,ccs,hdb3,crc4 cas=1-15:1101 dchan=16 cas=17-31:1101 span=2,0,0,ccs,hdb3,crc4 cas=32-46:1101 dchan=47 cas=48-62:1101 The first strange behavior is that the: zap show status shows this: Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1 OK 0 0 0 T4XXP (PCI) Card 0 Span 2 OK 0 0 0 T4XXP (PCI) Card 0 Span 3 OK 0 0 0 T4XXP (PCI) Card 0 Span 4 UNCONFIGUR 0 0 0...

...estarted on span 1 lspci -v 06:03.0 Communication controller: Digium, Inc. Wildcard TE405P (2nd Gen) (rev 02) Flags: bus master, medium devsel, latency 32, IRQ 201 Memory at 30004a00 (32-bit, non-prefetchable) [size=128] /proc/zapatel/1-4 with 5 being ZTDUMMY Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF ClockSource Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" B8ZS/ESF RED Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4"

...and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to draw this dialpan in the extensions.conf Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO T4XXP (PCI) Card 0 Span 1 OK 0 0 0 CCS HDB3 CRC4 0 db (CSU)/0-133 feet (DSX-1) T4XXP (PCI) Card 0 Span 2 RED 0 0 0 CCS HDB3 CRC4 0 db (CSU)/0-133 feet (DSX-1) T4XXP (PCI) Card 0 Span 3 RED 0 0 0...

...and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My zaptel.conf is as follows: # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) span=1,1,0,ccs,hdb3 # termtype: te bchan=1-15,17-31 hardhdlc=16 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" span=2,2,0,ccs,hdb3 # termtype: te bchan=32-46,48-62 hardhdlc=47 # Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" span=3,3,0,ccs,hdb3 #...

...r wrong. If Asterisk was dialing out but it didn't work, I'd assume a config problem, but it doesn't seem to recognize DAHDI as a channel type. Possibly relevant CLI output: CLI> dahdi show status Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1 OK 0 0 0 T4XXP (PCI) Card 0 Span 2 OK 0 0 0 T4XXP (PCI) Card 0 Span 3 OK 0 0 0 T4XXP (PCI) Card 0 Span 4 RED 0 0...

...th,eth1/00:30:48:84:74:25,24,0 bchan=1-23 dhcan=24 /etc/asterisk/zapata.conf: under [channels]: signalling=pri_net switchtype=5ess callerid=asreceived group=1 context=default channel => 1-23 *CLI> zap show status Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1 OK 0 0 0 T4XXP (PCI) Card 0 Span 2 UNCONFIGUR 0 0 0 T4XXP (PCI) Card 0 Span 3 UNCONFIGUR 0 0 0 T4XXP (PCI) Card 0 Span 4 UNCONFIGUR 0 0...

Hi all, We have our system hosted publicly and 4 phones are connected remotely at employee's home, and when they try to do a assisted transfer to one of the employee at the main office, the call is lost. For ex: person A calls person B, person B calls person C for assisted transfer, and as soon as person B hits transfer button again to transfer person A to C, the call is lost. But in the

Hey folks, I'm pulling my hair out on this situation and would welcome some advice: I'm using the AMI Manager to Originate calls onto 2 E&M wink T1 circuits via a T4XXP card from Digium. Everything works fine for about 600(+/- 50) calls then the Manager is suddenly unable to launch calls. Using ZapBarge to listen to the channels themselves you can hear the dtmf digits being dialed, but then either there is dialtone (again), or a fast busy signal. I've also n...

...channel => 156-170 channel => 172-176 channel => 32-46 channel => 48-62 etc\zaptel.conf # Autogenerated by /usr/sbin/zapconf on Wed Feb 20 10:13:17 2013 -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS RED span=1,1,0,ccs,hdb3 # termtype: te bchan=1-15,17-31 dchan=16 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS RED span=2,2,0,ccs,hdb3 # termtype: te bchan=32-46,48-62 dchan=47 # Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" #...

...ind_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf: (auto configured, first span only shown:) # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" span=1,1,0,ccs,hdb3,crc4 # termtype: te bchan=1-15,17-31 dchan=16 echocanceller=mg2,1-15,17-31 ---------------------------------------------------------------------- From /etc/asterisk/dahdi-channels.conf (included in chan_dahdi.conf): ; Span 1: TE4/0/1 "T4XXP (PCI)...

Hi, I'm getting the following error from an asterisk 1.6.0.9 installation: [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler This repeats a few times, then asterisk crashes. I can't seem to locate any info on this error at all. I'm using

...ccess to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times already. Please help. I'm quite frustrated at this point. Thank you in advance for any help. /etc/dahdi/system.conf # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 echocanceller=mg2,1-15,17-31 # Global data loadzone = nl defaultzone = nl /etc/asterisk/chan_dahdi.conf [trunkgroups] [channels] ; Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) gro...

...SK 2.6.11-12mdksmp #1 SMP i686 Intel(R) Xeon(TM) CPU 3.00GHz unknown GNU/Linux - Asterisk 1.2.4 - Zaptel 1.2.3 - Libpri 1.2.2 ============================================ ASTERISK*CLI> zap show status Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1 OK 0 0 0 T4XXP (PCI) Card 0 Span 2 NOP 0 0 0 T4XXP (PCI) Card 0 Span 3 NOP 0 0 0 T4XXP (PCI) Card 0 Span 4 RED/NOP 0 0 0 =...

...channel => 156-170 channel => 172-176 channel => 32-46 channel => 48-62 etc\zaptel.conf # Autogenerated by /usr/sbin/zapconf on Wed Feb 20 10:13:17 2013 -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS RED span=1,1,0,ccs,hdb3 # termtype: te bchan=1-15,17-31 dchan=16 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS RED span=2,2,0,ccs,hdb3 # termtype: te bchan=32-46,48-62 dchan=47 # Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" #...

...nnel 16 as D-channel anyway! [Aug 28 12:06:11] == Primary D-Channel on span 1 up [Aug 28 12:06:11] ERROR[10552]: chan_dahdi.c:8749 dahdi_pri_error: !! Got a UA, but i'm in state 7 foxtrot*CLI> zap show status Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1 OK 0 0 0 T4XXP (PCI) Card 0 Span 2 OK 0 0 0 T4XXP (PCI) Card 0 Span 3 OK 0 0 0 T4XXP (PCI) Card 0 Span 4 RED 0 0 0...

...onf # Autogenerated by /usr/sbin/dahdi_genconf on Tue Dec 22 01:59:02 2009 # If you edit this file and execute /usr/sbin/dahdi_genconf again, # your manual changes will be LOST. # Dahdi Configuration File # # This file is parsed by the Dahdi Configurator, dahdi_cfg # # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS/CRC4 RED span=1,1,0,cas,hdb3,crc4 # termtype: te #bchan=1-15,17-31 #dchan=16 cas=1-15:1101 dchan=16 cas=17-31:1101 echocanceller=mg2,1-15,17-31 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS/CRC4 RED span=2,2,0,ccs,hdb3,crc4...

...on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) --snip-- My initial though was interrupts, the LAN was connected via eth0, which is sharing with the t1xxp card running the WAN link. (The t4xxp card is for a future project and is idle) but I downed eth0 and switched the LAN to eth1. /proc/interrupts: CPU0 0: 140133158 XT-PIC timer 1: 125 XT-PIC keyboard 2: 0 XT-PIC cascade 9: 157178 XT-PIC eth1 10: 140137079...

...ing on. I also asked the provider and they tell me that everything looks OK on their side. Then I found out that if I disconnected the lines, the spans started to work correctly. The error persists a system reboot. Asterisk also does not indicate what the trouble is. When I enabled debug for wct4xxp, the following messages started to show: Jul 6 11:15:03 server kernel: wct4xxp: LOF/LFA detected on span 2 but debouncing for 2500 ms Jul 6 11:15:03 server kernel: wct4xxp: LOF/LFA detected on span 4 but debouncing for 2500 ms Jul 6 11:15:03 server kernel: wct4xxp: LOF/LFA detected on span 3...