search for: spa3000

Hi, all I am trying to figure out how to forward incoming PSTN call on SPA3000 to VoIP extension(s). Basically, I have converted my home to VoIP. I have normal phone (connected to SPA3000) and couple of IP phones. All call coming from VoIP DID do ring all phones (analogue via SPA3000 and IP ones). Now I need to do same thing for incoming PSTN calls. I have enabled gateway fu...

...eet our requirements. We have a completely funtional DISA which we use pretty much all the time. I works flawlessly with incomming SIP calls from several providers, IAX calls from FWD and with ZAP. Recently we came out with a situation where it doesn't work... with a SPA3000 PSTN Line. You can call, navigate de IVR, log in into our app, and then when you go to DISA, and DISA plays the dialtone... whatever you dial is not recognized... This was REALLY odd... so I made a network capture with Ethereal, and... the SPA actually STOPS sending the RTP Even...

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

I'm trying to get working a spa3000 with asterisk. My problem is I cant get wroking the incomming calls (I installed the lastest firmware). My problem is asterisk is rejecting the authentication from the spa3000. Asterisk answers forbidden (SIP/2.0 403 Forbidden) and I think I placed the username and password correctly... Sip.conf s...

More an echo algorithm question than a purely asterisk one... I have the following setup: Handset - PAP2 - Asterisk - SPA3000 - Telco And no matter what I do, I get echo on a call routed out via the PSTN when I talk into the handset, in the order of a hundred ms (my estimate, could be wildly inaccurate!). Echo will occur also when I have a handset plugged into the phone port on the SPA3000 (only when the call is routed v...

Hi, all A quick question. I have SPA3000 and trying to get call waiting to work. I do receive call waiting tone, however hook flash does not seem to work. I think, I set up SPA3000 correctly. Basically, doing HF 2 (switching calls in Australia) does not do anything. Is there any examples on how to setup hook flash operation in Asterisk?...

I am still haveing problems (echo) with my X100P but I'm thinking it has more to do with the server it is in which is not a negotiable item at this time. My question then is to the use of SPA3000's as a replacement from the FXO standpoint. 1. Can you setup the FXO port to recognize distinctinve ring and call a different context like you can do with Zap channels? Being able to call a different extension inside the same context would be even better. 2. What about fax? Can FXO recognize...

In my seemingly endless search for the cause of echo on my SPA3000, I wired it up in the following configuration: Analogue Handset <--> (FXS)SPA3000(FXO) <--> PAP2 And set the Line1 dialplan on the SPA3k to '(<:@gw0>S0)' which means that as soon as I pick up the handset I get linked straight through to the PAP2, which gives me dialtone....

Hi all, Can anybody explain what these values exactly mean. As you all know its the dialtone value on an SPA3000 of linksys. 350@-19,440@-19;10(*/0/1+2). Can anybody help me how to write this code for a dialtone of frequency 425 which is continous. Thanks Dan -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/200608...

Dear all, Can someone from Netherlands who has SPA3000 send me the Regional & Line1 settings. I'm not sure what is wrong but I can call from asterisk to phone attached to spa300 FXO, but not the other way. I tested three phones: siemens gigaset, tiptel 160 and hpoj k80(fax). Only tiptel 160 can call to the asterisk, other two just dial but not...

Hi, I'm using a SPA 3000 as FXO and FXS termination connected to my * box. I'm using the caller ID prefix trick explained here: http://www.voip-info.org/wiki-Sipura+3000. All seems to work really fine, there is only a problem when I hangup my IP phone after a conversation and the other party don't: in this case the PSTN line remains connected until the other party hangs up. Any

My porblem is incoing PSTN calls are being forwarde to the * box, the phone rings, but when the phone is picked up, the call is not taken - it continues to ring. I am forwarding the call to (<S0:6666>) in my dial plan Can anyone assist? This is driving my crazy! Extract from the * console Executing Dial("SIP/3001-047c", "SIP/2004") in new stack -- Called 2004 --

Hey, all... If this is too off-topic, I'd be grateful for directions to a more appropriate mailing list. I'm trying to set up Asterisk and some Sipura boxes. I've got an SPA-3000 which is registering twice with Asterisk - once for its FXS/Line1/VoIP1 and once for its FXO/PSTN/VoIP2. My eventual goal is to have inbound calls on its FXO ring four times on its FXS and then fail over to

Hi, I have a little situation here :( I have an Asterisk working, and in another office, a Sipura SPA-3000. I configured the SPA and I have the extension working, the incomming trunk working, but the outgoing trunk (peer) does not work. The issue is that I have a dynamic IP where the SPA is, and neither the SPA nor my router have DynamicDNS. So, if I

Hi, I'm using a Sipura SPA 3000 to receive calls from a PSTN line and to send them to Asterisk. But on Asterisk, I don't see the PSTN caller ID! I only have User ID of the SPA 3000 as caller number. The caller number is present on the PSTN line. I'm in france, maybe the SPA 3000 is not compatible? If you have an idea, please tell me! Thanks, Micka?l

I've a problem. I've some spa3000 and spa2100. Asterisk 1.2.4. Prefered codec g711u in both. Calleng from a fxs of spa2100 to the fxo of spa3000, all works ok. Then I call from a sip phone configured for using g729, to the fxo of spa3000, it also works ok. The problem is that after this, when, making again a new call from spa2100...

Hi, I have a little situation here :( Perhaps somebody can give me a hand with it. I have an Asterisk working, and in another office, a Sipura SPA-3000. I configured the SPA and I have the extension working, the incomming trunk working, but the outgoing trunk (peer) does not work. The issue is that I have a dynamic IP where the SPA is, and neither the SPA nor

...uot;stole" from me. I only bought from them because they showed a 4-day availability stock level! Now I'm screwed as it seems these are impossible to come by in the UK now since Sipura decided to discontinue it.. Now my back to my subject. Does anyone know of a decent replacement for the SPA3000. I need at least 1 FXO and 1 FXS but am willing to pay for 2 FXS on the same unit. What I'm looking for needs to be of a likable price to the SPA3000 which in it's hayday was retailing for around ?70 at some outlets. I'm primarily looking for something network attachable. But could stre...

http://www.zoomtel.com/products/voip_products.html anyone using these? they look very interesting in that they support ilbc, and they offer a separate cheaper model without g729 license. i'm wondering if their EC is better than the spa3000, and what the echo tail length is. -Dan

Problem: SPA3000 phone does not ring for incoming PSTN call although I can dial out. I set up my Sipura with the Voxilla Wizard which is pretty good but leaves out some important details. The Voxilla Wizard for Supura SPA3000 gave me a setting for PSTN Tab -> Dial Plans -> Dial Plan 8 (<S0:66610>)...