search for: scsi2

...s/scsi/scsi_transport_spi.ko kernel/drivers/scsi/aic7xxx/aic79xx.ko kernel/fs/reiserfs/reiserfs.ko Including: udev Bootsplash: SuSE-SLES (1280x1024) Thanks, Aravindh Puthiyaparambil Xen Development Team Unisys ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 49 (level, low) -> IRQ 18 scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 <Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs Vendor: SEAGATE Model: ST373207LW Rev: D702 Type: Direct-Access ANSI SC...

...able to get this combination to work by giving up on the Ultra320 setting and dropping back to 160 in the controller setup, but if anyone has suggestions or info it would be appreciated. Here's the dmesg output: sd 2:0:0:0: Attempting to queue an ABORT message:CDB: 0x1a 0x0 0x5c 0x0 0x40 0x0 scsi2: At time of recovery, card was not paused >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<< scsi2: Dumping Card State at program address 0x4 Mode 0x22 Card was paused INTSTAT[0x0] SELO...

...em hangs after this. But if I use the linux-2.6-xen0 kernel it works well. Does anyone know why this is happening and how I can make it go away? Thanks, Aravindh Puthiyaparambil Xen Development Team Unisys, Tredyffrin PA ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 49 (level, low) -> IRQ 18 scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 <Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs Vendor: SEAGATE Model: ST373207LW Rev: D702 Type: Direct-Access ANSI SC...

...ree_blocks: bit already cleared for block 19268224 EXT3-fs error (device sd(8,17)): ext3_free_blocks: bit already cleared for block 19268225 EXT3-fs error (device sd(8,17)): ext3_free_blocks: bit already cleared for block 19268226 I try to rebuild array but at the 12% appears this message 3w-xxxx: scsi2: AEN: INFO: Rebuild started: Unit #0. 3w-xxxx: scsi2: AEN: ERROR: Drive error: Port #0. 3w-xxxx: scsi2: AEN: ERROR: Rebuild failed: Unit #0. I restarted again the rebuild but 3w-xxxx: scsi2: AEN: INFO: Rebuild started: Unit #0. 3w-xxxx: scsi2: Unit #0: Command (f7545c00) timed out, resetting card....

I have a question regarding the building of the unified xen kernel (linux-2.6-xen) and the use of initrd. In the past I built both xen0 and xenU kernels; the xen0 default configurations had SCSI and Fusion MPT support compiled into the kernel. Now, they are built as modules. The problem is that I am unable to boot the xen kernel built that way, even though I am building an initrd. I have

...t2 filesystem to ext3. These are my errors on the /var/log/messages. Please tell me what you think about these. Harddrive problem ? etc.. Thanks. --> snip Feb 3 04:03:02 reallyreal syslogd 1.4.1: restart. Feb 3 04:05:00 reallyreal kernel: scsi : aborting command due to timeout : pid 0, scsi2, channel 1, id 0, lu n 0 Read (10) 00 19 72 fd 57 00 00 38 00 Feb 3 04:05:01 reallyreal kernel: scsi : aborting command due to timeout : pid 0, scsi2, channel 1, id 0, lu n 0 Read (10) 00 0d 0d 38 77 00 00 20 00 Feb 3 04:05:01 reallyreal kernel: scsi : aborting command due to timeout : pid 0, s...

...-- an 8006-2 for the system disks and 2 7500-8s. On the 7500s, I'm running an all software RAID50. This morning I came in to find the system hung. Turns out a disk went overnight on one of the 7500s, and rather than a graceful failover I got this: Jan 6 01:03:58 $SERVER kernel: 3w-xxxx: scsi2: Command failed: status = 0xc7,flags = 0x40, unit #3. Jan 6 01:04:02 $SERVER kernel: 3w-xxxx: scsi2: AEN: ERROR: Drive error: Port #3. Jan 6 01:04:10 $SERVER 3w-xxxx[2781]: ERROR: Drive error encountered on port 3 on controller ID:2. Check cables and drives for media errors. (0xa) Jan 6 01:04:10...

...append initrd=initrd.img load_ramdisk=1 prompt_ramdisk=0 ramdisk_size=8192 rw root=/dev/ram ZILIX_KERNEL=raid.s label scsi.s kernel Kernels/scsi.s/bzImage append initrd=initrd.img load_ramdisk=1 prompt_ramdisk=0 ramdisk_size=8192 video=vesa vga=791 rw root=/dev/ram ZILIX_KERNEL=scsi.s label scsi2.s kernel Kernels/scsi2.s/bzImage append initrd=initrd.img load_ramdisk=1 prompt_ramdisk=0 ramdisk_size=8192 rw root=/dev/ram ZILIX_KERNEL=scsi2.s label scsi3.s kernel Kernels/scsi3.s/bzImage append initrd=initrd.img load_ramdisk=1 prompt_ramdisk=0 ramdisk_size=8192 rw root=/dev/ram ZILIX_...

I am experimenting with a scsi2 HP SureStore DAT24 attached as an external device to an Intel P4 system. I am attempting to create a raw disk image of a dds2 tape made on a non linux system. My immediate problem is that I am trying to terminate a dd process and having no luck. dd was invoked thus: dd if=/dev/nst1 of=/tmp/d...

hi all We have a rh linux server connected to two HP SAN controllers, one an HSV200 (on the way out), the other an HSV400 (on the way in). (Via a Qlogic HBA). /etc/multipath.conf contains this : device { vendor "(COMPAQ|HP)" product "HSV1[01]1|HSV2[01]0|HSV300|HSV4[05]0" getuid_callout "/sbin/scsi_id -g -u -s /block/%n"

Hi All, Two and three-node clusters with SC3.2 and S10u3 (120011-14). If a node is rebooted when using SCSI3-PGR the node is not able to take the zpool by HAStoragePlus due to reservation conflict. SCSI2-PGRE is okay. Using the same SAN-LUN:s in a metaset (SVM) and HAStoragePlus works okay with PGR and PGRE. (both SMI and EFI-labled disks) If using scshutdown and restart all nodes then it will work. Also, (interesting) If I reboot a node and then run: update_drv -f ssd , then the node will be able...

...oping someone else using their iPod with Centos 4 could shed some light on this. When I attach my iPod via USB, I get these messages: 19:36:44 brahma kernel: usb 1-8: new high speed USB device using address 2 19:36:45 brahma kernel: Initializing USB Mass Storage driver... 19:36:45 brahma kernel: scsi2 : SCSI emulation for USB Mass Storage devices 19:37:35 brahma kernel: usb 1-8: reset high speed USB device using address 2 19:37:51 brahma kernel: scsi: Device offlined - not ready after error recovery: host 2 channel 0 id 0 lun 0 I had no problems getting my iPod to work under Centos 3 (2.4.x ke...

...hard drive is recognized - I believe, but just when the boot process shall continue to use my USB drive, mounting of devfs fails (see the attached image too): ... sda: assuming drive cache: write ... /dev/scsi/host2/bus0/target0/lun0:<7>usb-storage: .... p1 p2 Attached scsi disk sda at scsi2, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0 ReiserFS: sda2: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda2 kjournald starting. Commit interval 5 seconds. Ext3-fs: mounted filesystem with ordered data mode. mount: Mounting devfs...

...he SO_SNDBUF size at samba, and much more.. ) Which I see in iptraf, is the copy starts at 50000kbit/sec and after a while it's go under 2000-3000 kbit/sec, then go back to 50000kbit/sec .. and so on. My HW is a HP Proliant ML330T03 P4 Xeon 2.4G with 512M memory and the same size of swap.. 3* SCSI2 HDD netbios name = obelix workgroup = WORK os level = 64 preferred master = yes domain master = yes local master = yes security = user encrypt passwords = yes domain logons = Yes logon path = logon drive = u:...

...rev 0x20: ivec 0x7dc, address 00:03:ba:66:75:d2 brgphy1 at cas2 phy 1: BCM5421 10/100/1000baseT PHY, rev. 1 mpi1 at pci3 dev 2 function 0 "Symbios Logic 53c1030" rev 0x07: ivec 0x7e3 scsibus2 at mpi1: 16 targets, initiator 7 sd0 at scsibus2 targ 0 lun 0: <LSILOGIC, 1030 IM IM, 1000> SCSI2 0/direct fixed sd0: 34732MB, 34732 cyl, 16 head, 128 sec, 512 bytes/sec, 71131136 sec total sd1 at scsibus2 targ 2 lun 0: <FUJITSU, MAP3367N SUN36G, 0401> SCSI2 0/direct fixed sd1: 34732MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sec, 71132959 sec total sd2 at scsibus2 targ 3 lun 0: <FUJITS...

...k is /dev/sda, single filesystem-partition /dev/sda1 is labeled LABEL=/, and fstab uses the label to access the filesystem. I now add a SCSI-disk (previously used) to the onboard SCSI-controller, and the fun starts. The onboard controller is identified as scsi0 and scsi1, the SATA-disk sits on scsi2. SCSI-disk is thus /dev/sda, and SATA-disk becomes /dev/sdb. This should not be a problem as the fstab refers to the partition by label and not device name. And then disaster! While booting, the system issues 'Checking root filesystem' (I'm not 100% sure about the output here), and...

Hi *, I try to install Xen 3.0.0 on a IBM x342 with a ServeRAID 4Lx controller. The box boots with "plain" 2.6.12.6 (aic7xx- and serveraid-support included). It does not with a similar configuration of 2.6.12.6-xen0. Any hints, boot options? by Töns -- There is no safe distance. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com

...ntos but I am not sure about the mount point or the device point it is taking /dev/s?? Logs from /var/log/messages. Mar 11 11:30:06 l_l_box kernel: usb 1-1: USB disconnect, address 3 Mar 11 11:30:22 l_l_box kernel: usb 1-1: new high speed USB device using address 4 Mar 11 11:30:22 l_l_box kernel: scsi2 : SCSI emulation for USB Mass Storage devices Mar 11 11:30:22 l_l_box kernel: Vendor: CORNICE Model: Inc. Storage Ele Rev: 0 0 Mar 11 11:30:22 l_l_box kernel: Type: Direct-Access ANSI SCSI revision: 02 Mar 11 11:30:22 l_l_box scsi.agent[17229]: disk at /devices/pci0000:00/0000:00:1d...

...or 0xC9 and IRQ 17 ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 201 PCI: Setting latency timer of device 0000:00:11.0 to 64 ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xE400 irq 201 ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xE408 irq 201 scsi2 : sata_nv ata3: SATA link down (SStatus 0 SControl 300) scsi3 : sata_nv ata4: SATA link down (SStatus 0 SControl 300) Varian

...5 Gbps (SStatus 113 SControl 300) Jul 26 16:29:27 sauron kernel: ata1.00: qc timeout (cmd 0xa1) Jul 26 16:29:27 sauron kernel: ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104) Jul 26 16:29:27 sauron kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jul 26 16:29:27 sauron kernel: scsi2 : ahci Jul 26 16:29:27 sauron kernel: ata2: SATA link down (SStatus 0 SControl 300) Jul 26 16:29:27 sauron kernel: scsi3 : ahci Jul 26 16:29:27 sauron kernel: ata3: SATA link down (SStatus 0 SControl 300) Jul 26 16:29:27 sauron kernel: scsi4 : ahci Jul 26 16:29:27 sauron kernel: ata4: SATA link dow...