Displaying 8 results from an estimated 8 matches for "scrubing".
Did you mean:
scrubbing
2010 Dec 20
3
Resilvering - Scrubing whats the different
Hello All
I read this thread Resilver/scrub times? for a few minutes
and I have recognize that I dont know the different between
Resilvering and Scrubing. Shame on me. :-(
I dont find some declarations in the man-pages and I know the command
to start scrubing "zpool scrub tank"
but what is the command to start resilver and what is the different?
--
Best Regards
Alexander
Dezember, 20 2010
2013 Oct 19
13
[PATCH] Btrfs: fix race condition between writting and scrubing supers
From: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Scrubing supers is not in a transaction context, when trying to
write supers to disk, we should check if we are trying to
scrub supers.Fix it.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
---
fs/btrfs/disk-io.c | 2 ++
fs/btrfs/transaction.c | 2 ++
2 files changed, 4 insertions(+)...
2014 Jun 06
2
PROBLEM: new kernel 3.15.0-rc8 hangs completely with CONFIG_DRM_NOUVEAU enabled
Hello, guys.
First apologize my flaws, I am not a native English speaker and thus am
prone to stupid errors.
My box is an ASUSTek Notebook with Optimus capability (no, this is NOT
about Optimus, I don't try to use Optimus yet, so please don't switch
off here) with a running Gentoo. The first GPU is an Haswell-based Intel
chip, the second one is a nVidia GeForce GTX 850M, the chip is a
2008 Jan 25
1
Order of operations w/ checksum errors
zpool status shows a few checksum errors against 1 device in a raidz1 3 disk array and no read or write errors against that device. The pool marked as degraded. Is there a difference if you clear the errors for the pool before you scrub versus scrubing then clearing the errors? I''m not sure if the clearing errors prior to a scrub will replicate out any bad blocks that were identified as checksum errors previously that had since been cleared.
This message posted from opensolaris.org
2014 Jun 07
0
PROBLEM: new kernel 3.15.0-rc8 hangs completely with CONFIG_DRM_NOUVEAU enabled
First off, the current state of support for Maxwell (GM107/NV110) is
not very useful to end-users. It's especially not useful if it's a 3d
accelerator card without outputs (as yours appears to be), since
acceleration is not supported in 3.15 out of the box. You'd have to
figure out how to extract the context switching firmware from the blob
driver and load it in nouveau. I'm told
2014 Jun 07
1
PROBLEM: new kernel 3.15.0-rc8 hangs completely with CONFIG_DRM_NOUVEAU enabled
Yes, you are right - the Intel-chip is connected to the display, it just
offloads 3D work to do to the nVidia-chip, which isn't even to tell how
to get the EDID. I just wanted to try it out, simply for two reasons:
1. I heard that nouveau now "supports" the chip, and since I got the
hardware, I wanted to try it out - just for the fun of it. :)
2. As far as I am informed, a way to
2006 Nov 03
27
# devices in raidz.
for s10u2, documentation recommends 3 to 9 devices in raidz. what is the
basis for this recommendation? i assume it is performance and not failure
resilience, but i am just guessing... [i know, recommendation was intended
for people who know their raid cold, so it needed no further explanation]
thanks... oz
--
ozan s. yigit | oz at somanetworks.com | 416 977 1414 x 1540
I have a hard time
2010 Jun 29
2
Dell R605 w/ Perc 6/i problem
I think there was just a thread 'bout this, and I didn't pay attention...
and then I walked into our smallest server room to rebuild a server with
CentOS... and that's what it is. The problem I'm having is this: there are
two 1T SAS drives, raided, via the controller. There's also a 750G SATA
drive. The Dell test suite sees it, and reports that SMART says it's fine.