search for: regauth

...e is trying to connect: Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ Timestamp: 00000ms SCall: 22458 DCall: 00000 [192.168.2.1:4569] USERNAME : hayley REFRESH : 1800 Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH Timestamp: 00003ms SCall: 00010 DCall: 22458 [192.168.2.1:4569] AUTHMETHODS : 3 CHALLENGE : 193147468 USERNAME : hayley Rx-Frame Retry[Yes] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ Timestamp: 00000ms SCall: 22458 DCall: 00000 [192.168.2.1:4569]...

...sk 1.4.26-rc1 is available for immediate download at http://downloads.asterisk.org/pub/telephony/asterisk/ This release is primarily a fix for an issue (#14867, #14717) related to security fix AST-2009-001 where IAX was not sending REGREJ to terminate invalid registrations. Instead it sent another REGAUTH if the authentication challenge failed. This caused a loop of REGREQ and REGAUTH frames. Additionally, an issue (#15183) with broken attended transfers where the bridge was terminating immediately after the transfer is resolved in this release, along with some other issues reported by the community...

...sk 1.4.26-rc1 is available for immediate download at http://downloads.asterisk.org/pub/telephony/asterisk/ This release is primarily a fix for an issue (#14867, #14717) related to security fix AST-2009-001 where IAX was not sending REGREJ to terminate invalid registrations. Instead it sent another REGAUTH if the authentication challenge failed. This caused a loop of REGREQ and REGAUTH frames. Additionally, an issue (#15183) with broken attended transfers where the bridge was terminating immediately after the transfer is resolved in this release, along with some other issues reported by the community...

...etry[000] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: > REGREQ > Timestamp: 00007ms SCall: 00001 DCall: 00000 [66.234.228.170:4569] > USERNAME : nWv96gaD75 > REFRESH : 60 > > Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: > REGAUTH > Timestamp: 00012ms SCall: 00055 DCall: 00001 [66.234.228.170:4569] > AUTHMETHODS : 3 > CHALLENGE : 164462354 > USERNAME : nWv96gaD75 > > Tx-Frame Retry[000] -- OSeqno: 001 ISeqno: 001 Type: IAX Subclass: > REGREQ > Timestamp: 00049ms SCal...

....199.163:4569] Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ Timestamp: 00011ms SCall: 00003 DCall: 00000 [212.29.199.163:4569] USERNAME : ilavender REFRESH : 60 Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH Timestamp: 00017ms SCall: 00170 DCall: 00003 [212.29.199.163:4569] AUTHMETHODS : 3 CHALLENGE : 101355226 USERNAME : ilavender Tx-Frame Retry[000] -- OSeqno: 001 ISeqno: 001 Type: IAX Subclass: REGREQ Timestamp: 00017ms SCall: 00003 DCall: 00170 [212...

...to refresh registration (0x13) Length: 2 When to refresh registration: 60 No. Time Source Destination Protocol Info 2 0.072646 65.39.205.121 68.146.107.231 IAX2 IAX, source call# 1867, timestamp 11ms REGAUTH <snip> Inter-Asterisk eXchange v2 <snip> Type: IAX (6) IAX type: REGAUTH (14) Information Element: Authentication method(s) (0x0E) IE id: Authentication method(s) (0x0E) Length: 2 Authentication method(s): 0...

...-22 15:14:06 DEBUG[6855] devicestate.c: Changing state for IAX2/support - state 5 (Unavailable) 2006-11-22 15:14:06 DEBUG[6863] chan_iax2.c: Sending 3 on 3/20971 to 10.0.10.160:4569 2006-11-22 15:14:06 VERBOSE[6863] logger.c: Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH 2006-11-22 15:14:06 VERBOSE[6863] logger.c: Timestamp: 00003ms SCall: 00003 DCall: 20971 [10.0.10.160:4569] 2006-11-22 15:14:06 VERBOSE[6863] logger.c: AUTHMETHODS : 1 2006-11-22 15:14:06 VERBOSE[6863] logger.c: USERNAME : support 2006-11-22 15:14:06 VERBOSE[6863] logger.c: 2...

Asterisk 1.4.31 IAX2/RSA BUG If "A" tries to register on "B" and the RSA key from "A" does not match the key on "inkeys" on "B", "B" do not send a "REGREJ", instead it sends a "REGAUTH" with a new "CHALLENGE", then "A" send a new "REGREQ" for this "CHALLENGE" with the same wrong RSA key and it loops forever on this (with a storm of REGREQ <--> REGAUTH packets). The same was true in version 1.2.31.1, but was corrected in a patch....

Asterisk 1.4.31 IAX2/RSA BUG If "A" tries to register on "B" and the RSA key from "A" does not match the key on "inkeys" on "B", "B" do not send a "REGREJ", instead it sends a "REGAUTH" with a new "CHALLENGE", then "A" send a new "REGREQ" for this "CHALLENGE" with the same wrong RSA key and it loops forever on this (with a storm of REGREQ <--> REGAUTH packets). The same was true in version 1.2.31.1, but was corrected in a patch....

...MYNUMBER):(MYPASSWORD)@cts-au.freshtel.net [firefly] type=friend host=cts-au.freshtel.net context=from-firefly I never see a "registered" message when starting up * (I do for FWD) When sniffing the interface I can see the following IAX2 data on startup. REGREQ (From me -> freshtel) REGAUTH (Freshtel -> Me) REGREQ (Me -> Freshtel) REGACK (Freshtel -> Me) ACK (Me -> Freshtel) My extensions.conf looks like exten => _394.,1,SetCallderId(MYNUMBER) exten => _394.,2,Dial(IAX2/MYNUMBER:MYPASSWORD@cts-au.freshtel.net/${EXTEN:3},60,r) Again, similar setup is working with...

Is there a database of MAC address prefixes used the common VoIP devices. I see the Linksys Sipura devices state with 00:0E. Does the same apply to other Linksys VoIP equipment? Is there some way VoIP equipment allow themselves to be identified by requesting data from some ports?

...), and then * goes to vmail. Here's the debug output: affinity*CLI> iax debug IAX Debugging Enabled Rx-Frame Retry[N/A] -- Seqno: 00 Type: IAX Subclass: REGREQ Tx-Frame Retry[-01] -- Seqno: 00 Type: IAX Subclass: ACK Tx-Frame Retry[000] -- Seqno: 00 Type: IAX Subclass: REGAUTH Rx-Frame Retry[N/A] -- Seqno: 00 Type: IAX Subclass: REGREQ Tx-Frame Retry[-01] -- Seqno: 00 Type: IAX Subclass: ACK Rx-Frame Retry[N/A] -- Seqno: 00 Type: IAX Subclass: ACK Rx-Frame Retry[N/A] -- Seqno: 01 Type: IAX Subclass: REGREQ Tx-Frame Retry[-01] -- Seqno: 01 T...

This may not strictly be an asterisk question, but not sure where else to post ... I have an Asterisk test server setup with two firefly clients, one on the local lan and one on an external ip address. Both clients are setup the same way and voice calls work fine. The asterisk console reports a "Registered" message for the external client at about one minute intervals but the

...rame Retry[000] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ Timestamp: 00063ms SCall: 03639 DCall: 00000 [63.211.239.14:4569] USERNAME : gswoods REFRESH : 60 CALLTOKEN : 51 bytes Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH Timestamp: 00019ms SCall: 03026 DCall: 03639 [63.211.239.14:4569] AUTHMETHODS : 3 CHALLENGE : \x31\x33\x34\x35\x38\x37\x34\x39\x31 USERNAME : gswoods Tx-Frame Retry[000] -- OSeqno: 001 ISeqno: 001 Type: IAX Subclass: REGREQ Timestamp: 00115ms SCall: 03639 DC...

...: 00000 [89.31.XX.XX:4569] [Aug 27 11:36:08] Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: ACK [Aug 27 11:36:08] Timestamp: 00003ms SCall: 00414 DCall: 10189 [XX.31.XX.XX:4569] [Aug 27 11:36:08] Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH [Aug 27 11:36:08] Timestamp: 00007ms SCall: 00414 DCall: 10189 [XX.31.XX.XX:4569] [Aug 27 11:36:08] AUTHMETHODS : 4 [Aug 27 11:36:08] CHALLENGE : 129701753 [Aug 27 11:36:08] USERNAME : server2 [Aug 27 11:36:08] [Aug 27 11:36:08] NOTICE[30153]: chan_iax2.c:5916 authen...

...register: voip*CLI> Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ Timestamp: 00000ms SCall: 03341 DCall: 00000 [192.168.1.101:4569] USERNAME : client1 REFRESH : 1800 Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH Timestamp: 00016ms SCall: 00003 DCall: 03341 [192.168.1.101:4569] AUTHMETHODS : 1 USERNAME : client1 Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: INVAL Timestamp: 00016ms SCall: 03341 DCall: 00003 [192.168.1.101:4569] when I change the ip to...

The Asterisk Development Team has released Asterisk versions 1.2.33, 1.4.25.1, 1.6.0.10, and 1.6.1.1. The released versions are available at http://downloads.asterisk.org/pub/telephony/asterisk/ This release fixes a REGAUTH loop related to security issue AST-2009-001. Asterisk release 1.2.33 also addresses a small compile time error in chan_spy. For more information about the security issue, please see: http://downloads.asterisk.org/pub/security/AST-2009-001.html For a summary of the changes in this release, please...

...on session: *CLI> Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ Timestamp: 00003ms SCall: 05274 DCall: 00000 [192.168.1.178:4569] USERNAME : rwebb REFRESH : 300 Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH Timestamp: 00006ms SCall: 00004 DCall: 05274 [192.168.1.178:4569] AUTHMETHODS : 2 CHALLENGE : 52832788 USERNAME : rwebb Rx-Frame Retry[ No] -- OSeqno: 001 ISeqno: 001 Type: IAX Subclass: REGREQ Timestamp: 00040ms SCall: 05274 DCall: 00004 [192.168.1....

The Asterisk Development Team has released Asterisk versions 1.2.33, 1.4.25.1, 1.6.0.10, and 1.6.1.1. The released versions are available at http://downloads.asterisk.org/pub/telephony/asterisk/ This release fixes a REGAUTH loop related to security issue AST-2009-001. Asterisk release 1.2.33 also addresses a small compile time error in chan_spy. For more information about the security issue, please see: http://downloads.asterisk.org/pub/security/AST-2009-001.html For a summary of the changes in this release, please...

...What did I forget to do??? Rx-Frame Retry[No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ Timestamp: 00001ms SCall: 10489 DCall: 00000 [192.168.50.66:4569] USERNAME : 100 REFRESH : 300 Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: REGAUTH Timestamp: 00008ms SCall: 00001 DCall: 10489 [192.168.50.66:4569] AUTHMETHODS : 3 CHALLENGE : 455913197 USERNAME : 100 Rx-Frame Retry[No] -- OSeqno: 001 ISeqno: 001 Type: IAX Subclass: REGREQ Timestamp: 00047ms SCall: 10489 DCall: 00001 [192.168.50.66:4569]...