search for: pumbg

Running CentOS 6.4. Hi I have a bunch of Intel systems. Ivy Bridge Q77 chipset with 82579LM nics. I can't seem to wake them up with ether-wake. The nic driver is the intel e1000e. #ether-wake -i ethX mac-addr Once up (manually) ethtool reports Supports Wake-on: pumbg Wake-on: g I'm sure I've set the bios up properly. Any advice?

...1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 10Mb/s Duplex: Half Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes ethtool says the device has auto-negotiate off and running half duplex. Any attempts to use ethtool to fix it fail. So my biggest frustration is that this network card works on CentOS 5.5. The main difference between...

...100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes

My system is: Intel CC820 motherboard (which supports PME# wake up for wake on LAN) 3com 3C905C which also supports wake on LAN via PME# Linux 5.5 The motherboard BIOS is later than one that reports an issue with WOL and this particular network card was fixed. But when I turn off the PC (shutdown or poweroff commands or front panel button), it cannot be restarted via WOL. The network light on

Hello, Just did a fresh install of xen-4.0 and using the 2.6.31.13 dom0 kernel. I have 6 linux debian guests running, and on my host console i am getting these errors rolling pretty constantly. "Attempting to checksum a non-TCP/UDP packet, dropping a protocol 1 packet" I tried doing the ethtool -K eth0 tx off and same thing on peth0, using bridged mode for network config. Any tips?

Hello, Just did a fresh install of xen-4.0 and using the 2.6.31.13 dom0 kernel. I have 6 linux debian guests running, and on my host console i am getting these errors rolling pretty constantly. "Attempting to checksum a non-TCP/UDP packet, dropping a protocol 1 packet" I tried doing the ethtool -K eth0 tx off and same thing on peth0, using bridged mode for network config. Any tips?

...1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes And the nic stats also look good: root at communiceer:~# ethtool -S eth1 NIC statistics: rx_packets: 6071960 tx_packets: 6189424 rx_bytes: 1244...

...baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: on (auto) Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes -- john r pierce, recycling bits in santa cruz

.../Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes mpower@dodtsair:~$ sudo /etc/Xen/scripts/network-bridge status ============================================================ 10: peth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 10...

On 10/10/2016 09:31 PM, John R Pierce wrote: > > oh. Yeah, the entire "net-tools" package is deprecated. I tend to forget which of the two (ethtool or mii-tool) is in that set. # Avoid using any of these: $ rpm -ql net-tools

Dear All, I have an onboard Realtek RTL8111/8168B NIC. from lspci -vv : 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) It is detected, but why the speed is always 100Mbps, already change cable but still no luck. I use ethtool and from the output it seems that system know that this NIC support gigabit speed : ???????

Hi folks on debian stable I've a default samba file sharing config. Everything works perfectly (almost...) - samba version 3.6.6 >From linux and windows clients (wired and wifi too) when I (i.e. listen musics) often (one time every 4/5 minutes) networks suddenly collapse (for less one second) and immediately goes up. So I've an interrupt of broadcast (this happens also if I use rsync

...tised auto-negotiation: Yes > > Speed: 1000Mb/s > > Duplex: Full > > Port: Twisted Pair > > PHYAD: 1 > > Transceiver: internal > > Auto-negotiation: on > > MDI-X: on > > Supports Wake-on: pumbg > > Wake-on: g > > Current message level: 0x00000007 (7) > > drv probe link > > Link detected: yes > > > > > > And the nic stats also look good: > > > > root at communiceer:~# ethtool -S eth...

I've got a pair of identical CentOS 6.7 servers, with SuperMicro X8DTE-F motherboards, these have 2 each Intel 82574L ethernet ports. The eth0 ports are plugged in with 10' runs of brand new cat 5e cable to a Cisco Nexxus 9000 switch (provided by the data center). These servers keep coming up at 100baseT rather than gigE. I've swapped ports and cables with a different server,

I am attempting to build an IPv4/IPv6 router. I have put a 2nd ethernet card in a box. I have one Ethernet card attached to my network and the other to a switch with nothing else there just so the link comes up for testing. When I have the built-in Ethernet attached to my network, I get pings around 60ms. The other card, btw, does not have any IP addresses configed. When I switch the

I''m going to set up a PVM on xen-3.3.1 debian-amd64. I need advices about the best methods to install a fresh debian on it (i.e. how to choose the kernel for pvm) . I''ve installed xen from sources and only have one xen kernel in /boot which I''m using for dom0; should I use the same kernel for domUs? There is any problem on use vcpus=2; the other vm is an hvm running

Dovid Bender writes: > The tcpdump that you are running is on the Asterisk box or via port > mirroring? It's on the asterisk box itself. I've already replaced the network card - no change. Thanks, Roel > Regards, > > Dovid > > -----Original Message----- > From: Roel van Meer <roel at 1afa.com> > Sender: asterisk-users-bounces at

Hi. I am trying to setup my firewall in DomU. However, I have got a little problem. My pon dsl-provider exits with following message. Nov 18 09:44:40 alsfw01 pppd[1723]: Plugin rp-pppoe.so loaded. Nov 18 09:44:40 alsfw01 pppd[1723]: Linux kernel does not support PPPoE -- are you running 2.4.x? Nov 18 09:44:40 alsfw01 pppd[1723]: Exit. I am running xen out of the box on Debian Stable. My