search for: pradeshta

...from Varion, or from Digium (not supported by them though) but what about "cheap" channel banks, that are economical and no frills, good for loop start/ground start with no polarity reversal, FXS variety. Any suppliers of these devices, please contact me off list. (haque at at nmc dot dot pradeshta dot dot net). -samudra --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.797 / Virus Database: 541 - Release Date: 11/15/2004 -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/...

hello, using a legacy PBX to access a Asterisk Zap channel (Legacy PBX FXS --> FXO application Asterisk/TDM400P) I want to be able to "flash" the asterisk pbx. However by pressing the FLASH button on the extension connected to the Legacy PBX gets me the flash features on the Legacy PBX, not on the Asterisk PBX side. I thought of using the following codes (listed below) from

Hello, I want to use Asterisk PBX in front of my old, legacy PBX. The legacy PBX can be outfitted with caller-ID and is already able to handle Calling Party Control Signal Detection (this is a Panasonic KX-TD1232 Super Hybrid PBX. My question is how would one enable Asterisk to control the TDM400P/FXS port to provide to the /FXO CO port on the legacy PBX, support for proper answer supervision/CPC

[this message is a resend, I apologise for duplicates, but I think the original mail did not make it.] 12/3/2004 hi, I followed the instructions faithfully in http://www.voip-info.org/wiki-Asterisk+Fedora+Core+3 and the directions were very understandable and almost painless. I did miss the documentation, as "make progdocs" would not work since the package "doxygen" was not

> > You need to configure your legacy PBX to send a flash through from your > legacy phone to the legacy FXS port that is hooked to a * FXO port. This > is not something you can do from the * side. > > *0 is asterisk's way of doing this. You need to find out if your legacy > PBX has a similar method. It may not be possible. Of course you failed > to mention what kind of

Hello, I would like to parse inbound Asterisk IAX2 7-digit numbers in the form of 123-4567 and strip out the first four digits, and then dial whatever number digits remain. If I only have three digits (000-999) and have a mix of channels (ZAP, SIP, IAX2) could someone please point out how I can use a single DIAL command to just dial the extension regardless of the type of channel. .. For each

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.6 - Release Date: 12/28/2004

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.300 / Virus Database: 265.6.8 - Release Date: 1/3/2005

hi, I followed the instructions faithfully in http://www.voip-info.org/wiki-Asterisk+Fedora+Core+3 and the directions were very understandable and almost painless. I did miss the documentation, as "make progdocs" would not work since the package "doxygen" was not included in that WIKI guide, and probably that means I will have to spend some more time in "digging"

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support

Hello, I thought that my Digium TDM400P would be the right hardware to support the zaptel timer, and put the following IAX.CONF entry to test, (trunk=yes) in the example below [VHAX] type=peer auth=md5 username=whoknows jitterbuffer=yes ;trunk=yes secret=terriblesecret host=4.5.6.7 qualify=1200 disallow=all allow=ulaw allow=gsm ;allow=g711u ;allow=g711a But, it didn't work. So I had to

Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO

[resend in plain text format] > On Tue, 2004-12-07 at 09:34 -0600, asterisk-users- > > request@lists.digium.com wrote: > > > I've been struggling with a test * install for a couple months now in a > > > small office and am just about ready to give up on it. It's not that the > > > system itself is a problem. I've got everything (attendant,

> On Tue, 2004-12-07 at 09:34 -0600, asterisk-users- > > request@lists.digium.com wrote: > > > I've been struggling with a test * install for a couple months now in a > > > small office and am just about ready to give up on it. It's not that the > > > system itself is a problem. I've got everything (attendant, voicemail, > > > FXS

hi, I received this e-mail which contains a "ballad", at first I thought it was junk mail, but then I read through it, for the EE members of this list, it may be quite humorous. I don't know if the ballad is original, but at least it's the XMAS season, so it's something to lighten up your day, eh? -samudra """ How the Ground Loop Stole Christmas