search for: openline4s

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Is anyone using the VoiceTronic Openline4 PCI (fxo) card? I am trying to setup Asterisk using a Digium 40B (4 port fxs) and an OpenLine4 (4 port fxo), however I can't find any examples or post that utilize this card. I have my stations (Sayson 390) ringing each other, but haven't had any success ringing out. I have the OpenLine4 loaded and all of the new drivers working good, just

Hi all, Can somebody help me get my OpenLine4 card running with asterisk@home? I've got my VPB drivers configured, but can't figure out how to map trunks and channels the typical way in the AMP config interface for Asterisk@home. Apparently I'm supposed to use /vpb/1 type commands, but I'm not sure how it should work. I'm relatively new to asterisk, I did a bunch of

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Hi fellows I'm trying to set up an OpenLine4 card to an A@H I made a "custom trunk" and putting a "dial string" like this "vpb/1-1/$OUTNUM$" I configured the outbound routing using "8|." as patern and "NXXXXXX" as dial rule..., but I'm getting an "all circuits are busy now" when I dial "8NXXXXXX" Here is my vpb.conf

Hi I would like your comments on the openline4 card from voicetronix. I am trying to get one working and find it difficult. I was able to get asterisk working yesterday but now it doesn't work anymore While it worked I was able to make some calls and I heard a lot of jitter Any comments appreciated. Patrick

Hello, list, I am using Asterisk with an OpenLine4 card. It worked well with Asterisk 1.0. Then I upgraded the system, Asterisk 1.4 had some problem to compile chan_vpb, but I managed to compile it manually. Still Asterisk does not work because it refused to load chan_vpb module. I had to revert back to install Asterisk 1.2. Then I get a error: asterisk: hip.cpp:793:

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

Hi all, I used to have an OpenLine4 card, but decided against using it due to some problems with hangup detect. Does anyone on the list actively use Voicetronix's OpenSwitch12? What are your opinions on the card? Cheers, Flynn

Good day all I'm using sip protocol and a openline4 card.If I dial out of the pstn and hangup a answered call it does not disconnect the connection.It shows there is still a call on the external phone I called but on my side its says i'm not connected.We are using x-ten soft phones Can someone please help me Thanks Altus

Good day all I'm getting this error while trying to dial out on my asterisk server using a openline4 card "exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872" Please Help me

Good day all We have a voicetronix openline4 card If someone calls in from the outside the pstn and into the system and hangsup asterisk does not deteck the hangup any Idea why please Help Altus

Good day all I'm in South-Africa,currently we are using openline4 cards for our pbx systems.Now we first need approval on the cards form icasa(a government standards) before we can use the card.The market here is very big for a system like asterisk.The only problem is to get a card approved(for a small company like us) its just about impossible. Now what I'm looking for is a company that

I am just starting to deploy asterisk in our office to use as our primary phone system - we plan to use a Voicetronix OpenLine4 card as our PSTN gateway - but one thing at a time... haven't got that far yet. Currently, i'm trying simple IP to IP calls within the office using our Cisco 7960's phones running SIP. When I make a call between these two phones, the conversation is of a

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

Before I start ... I know there's been a lot of talk over the last couple of days about the list being slow etc... I understand there were problems and that mail is starting to get through now. Just wondering - should I be surprised if something I sent 48 hours ago hasn't turned up at all? And something I sent about 6 hours ago still hasn't turned up (yet). I'm just curious

Good day all So I've installed asterisk with my openline4 card and I've setup sip and I can do sip on the local network,we are using soft clients,x-lite. But... When a call comes in from the outside(PSTN) and the you dial the extension it forwards the call the the client and you see incoming call on x-lite,you accept he call....BUT there is no sound.It shows there is a call and you are

Ron, VoiceTronix worked with me last week and backported the new chan_vpb that's in the current HEAD CVS tree to the 1.0 stable branch. So if you are using 0.7.2 or 0.9.0 you can go to the VoiceTronix website now (note that this is very new) and download an Asterisk package. When you download it there is an new chan_vpb.c that needs to be put in your asterisk source code tree. Also there

Good day all I want to put the openline4 card into a box that will support 3 different companies I read the caller ID id fixed but now HOW DO I: If a call come in for 12345 it plays company 1's welcome message If a call come in for 98765 it plays company 2's welcome message ens.. Does This make sense Thanks Altus