search for: multipathed

Hi, WARNING: Long post ahead I have an issue when starting multipathd. The kernel complains about "blk_cloned_rq_check_limits: over max segments limit". The server in question is configured for KVM hosting. It boots via iBFT to an iSCSI volume. Target is COMSTAR and underlying that is a ZFS volume (100GB). The server also has two infiniband cards providing four (4) more paths over SRP

I am attempting to get multipath working with device-mapper (CentOS 4.2 and 4.3). It works on EVERY install of mine from RH (also v4.2, 4.3), but the same multipath.conf imported to all my installs of CentOS do not work. Note that I have tested a working 4.2 configuration file from RH on CentOS 4.2 and a working 4.3 configuration (it changed slightly) on CentOS 4.3. Neither worked. Our production

We've been wrestling with this for ... rather longer than I'd care to admit. Host / initiator systems are a number of real and virtualized CentOS 5.5 boxes. Storage arrays / targets are Dell MD3220i storage arrays. CentOS is not a Dell-supported configuration, and we've had little helpful advice from Dell. There's been some amount of FUD in that Dell don't seem to know what

We''re currently designing a ZFS fileserver environment with iSCSI based storage (for failover, cost, ease of expansion, and so on). As part of this we would like to use multipathing for extra reliability, and I am not sure how we want to configure it. Our iSCSI backend only supports multiple sessions per target, not multiple connections per session (and my understanding is that the

The reason for the behaviour observed below turned out to be that the device entry in /etc/multipath.conf was inadvertently appended *after* the devices section , rather than inside it - so that we had #devices { # device { # blah blah # } (file has a bunch of defaults commented out) # etc #} # # device { our settings } *rather than*

The following patches introduce support for multipath and cciss devices to the ovirt-node and node-image. Comments are appreciated. These patches assume that the 3 patches (2 node, 1 node-image) from Joey are all incorporated. Mike

Hello! I have trouble with multipath routing. Those options are enabled in kernel: [*] IP: policy routing [*] IP: equal cost multipath [*] IP: equal cost multipath with caching support (EXPERIMENTAL) <*> MULTIPATH: round robin algorithm But issuing: ip r a 1.2.3.0/23 scope global equalize nexthop via 80.245.176.11 \ dev eth0 weight 1 nexthop via 80.245.176.13 dev eth0

Hi all, Writing up some Fedora documentation, and looking to figure out the best way of mapping multipath network(!) LUNs to pools in libvirt. ie Infiniband SRP LUNs, but would probably apply to Fibre Channel equally as well. There are two approaches I can think of easily: a) Large LUNs (ie TB+) that are mapped to a host server as disk, with each LUN being configured as an LVM

Hi list! I have a server with dual port Qlogic iSCSI HBA. I set up the same LUN for both ports, and boot the CentOS installer with "linux mpath". Installer detects multipathing fine, and creates mpath0 device for root disk. Installation goes fine, and the system boots up and works fine after the install from the multipath root device. After install the setup is like this: LUN 0 on

Using CentOS 5.1, though with a few hours work I could update to 5.2.. I can install to SAN with a single path no problem but I'd like to be able to use dm-multipath. From the kickstart docs it seems this is supported but there is no information as to what the various options mean http://www.centos.org/docs/5/html/5.1/Installation_Guide/s1-kickstart2-options.html -- multipath (optional)

Hello I am wondering if anyone este tried this. I Have few CentOS 6.2 systems that are running KVM virtual machines. As storage backend for them I use 2 iscsi targets (based on openindiana). For accessing these disks I use dm-multipath, since I use 2 separate networks for access. For these reasons I want host system to force not to scan dm-multipath disks for partitions. According to

All other patches from the sequence remain unchanged. Repost of patch 6 based on comments from Joey to follow. Mike

Hi, I am tring to us ip route to load balance between two interfaces. ip route add equalize 10.200.1.0/24 nexthop via 10.200.0.2 dev neta nexthop via 10.200.0.2 dev neta2 Where neta and neta2 are gre tunnels. Testing show that packets travel in a single sided manner. Do I need to use the multipath (IP_ROUTE_MULTIPATH_CACHED) module? thx jason

Hi all, I am trying to configure a failover multipath between 2 GNBD devices. I have a 4 nodes Redhat Cluster Suite (RCS) cluster. 3 of them are used for running services, 1 of them for central storage. In the future I am going to introduce another machine for central storage. The 2 storage machine are going to share/export the same disk. The idea is not to have a single point of failure

Hi, I do have one iscsi storage with 4 GBit nics of which currently only one is configured with an ip and which is in productive use by one cent os 6.3 server. Doing some research brought me to the idea to use some nic bonding or multipathing for that storage, but multipathing I did about four or five years ago only once :) Furthormore I can't find the ultimate answer (may be there is not

Hello, I hope to be in the right list. my question is the following. I can''t seem to get multipathing configure on XCP 1.6. In XenCenter I was able to enable "Multipath" however, in the LUN under general tab I see " multipath 1 of 1 active", the the CLI I do the following command xe --m node session it list only one session. Can someone help me please? Thanks in

I was playing a bit with multipathed devices (over two FC HBAs on SAN) last week (I had some hardware for limited time to play with). The support for multipathing in device mapper seems to be a bit newer thing, and I was left with couple of questions (things I haven't managed to try out while I had the hardware)... Is it possibl...

Hopefully someone can help get multipath working inside a domU. I'm using Xen 4.2.3 on a SLES 11 dom0, and both a SLES11 domU and a CentOS 6 domU. I'm using NPIV to connect my SAN disks to my domU, and, due to the way my SAN presents the LUNs, need to use multipath inside the domU. I've tried this on both SLES11 and CentOS6 with pretty much the same result. The root issue seems to

Hello, suppose I want to use a special configuration for my IBM/1814 storage array luns, then I put something like this in multipath.conf devices { device { vendor "IBM" product "^1814" product_blacklist "Universal Xport" path_grouping_policy "group_by_prio" path_checker

I've got my RAC cluster running pretty smoothly now (thanks again for all the help so far), but I only have single connections between the servers and the RAID array. The servers each have two Qlogic HBAs, and I'd like to find out if there's any reasonable way to implement multipathing. The platform is RHEL 3, and Red Hat's knowledgebase indicates that they strongly recommend