search for: misdnportinfo

Hello. Just installed the Beronet BN4S0 card. But i can't connect to my ISDN Line. misdnportinfo gives (what does ":Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib" mean?): best regards and thanks t. asterix asterisk # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is...

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (E...

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. -> childcnt: 2 * Port NOT useable for PBX (maybe there is already a PBX running?) -------- Port 2: TE-mode BRI S/T interface...

..., I am struggling to get plain Cologne chip cards to run in NT mode, runs nice in TE mode despite the error message: login as: root root at 192.168.2.22's password: Last login: Tue Sep 1 23:09:24 2009 from 192.168.2.50 Welcome to Elastix ---------------------------------------------------- misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. -> childcnt: 2 * Port NOT useable for PBX (maybe there is already a PBX running?) -------- Port 2: TE-mode BRI S/T interface...

...week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x9846060) irp(0x9846060) iend(0x9846060) /etc/asterisk/misdn.conf has this group definition: [extern] ports=1 context=misdn msns=...

Hello ! I 'm trying T.38 faxig with spandsp using rxfax/txfax as fax terminal. As another endpoint I 'm using Grandstream HT 486 ATA and a fax machine. Has anybody success with the HT486 as T.38 terminal ? ATA as originator: I managed only onetimes a successfull T.38 fax session. The other times the HT486 did not initiate a re-invite with T.38 parameters. Or shall the Terminator

...The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface can be Poin-To-Point/Multipoint. -------- Port 2: NT-mode BRI S/T interface port (for phones) -> Interface can be Poin-To-Point/Multipoint. -------- However when checking in Asterisk Layer 1 is always down even though the R...