search for: mfc

...stcall with one E1, it works fine; I receive DNIS and ANI for making calls and answering calls. ? When I start the Asterisk I receive call from outside correctly including DNIS and ANI, and receive the following messages: ? Sep? 7 10:29:59 WARNING[12167]: Answer Call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5) Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Answer call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 0101? ->????? [1/????? 20/Group B?????? /Accepted Paid] Sep? 7 10:29:59 WARNING[12167]: Unicall/2 event Answered Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCa...

...f ECHO in the destination". "F" is "end of the digits". They could help me? Best Regards Josu? -- Executing Dial("SIP/1196082068-082a6b78", "Unicall/g1/01197831234|90|tT") in new stack Dec 5 22:48:04 WARNING[5121]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Call control(1) Dec 5 22:48:04 WARNING[5121]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Make call Dec 5 22:48:04 WARNING[5121]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 Making a new call with CRN 32769 Dec 5 22:48:04 WARNING[5121]: chan_unicall.c:627 unicall_rep...

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Sei...

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I have a astunicall-1.4 setup with a te110p to a nortel pbx in Mexico. (Hate R2!). This is what I get when trying to call to * box using testcall: ./testcall Chan 31, class 'mfcr2', variant 'mx,20,4', end 0, caller 0, from '' to '' Loading protocol mfcr2 Thread for channel 0 MFC/R2 Chan 31: Call control(9) MFC/R2 Chan 31: Unblock MFC/R2 Chan 31: 1001 -> [1/BLOCKED /Idle /Idle ] MFC/R2 Chan 31: far_unblocking_expired...

I have a wired problem, i can recive call but i can't make any call. ATT say that is my problema because the call is operator mode (???) The log is MFC/R2 Chan 1: Call control(1) MFC/R2 Chan 1: Make call MFC/R2 Chan 1: Making a new call with CRN 32772 MFC/R2 Chan 1: 0001 -> [1/ 1/Idle /Idle ] Chan 1: -- Dialing on channel 0 Chan 1: -- Dialing on channel 0 MFC/R2 Chan 1: <- 1101 [1/ 40/Sei...

...stem run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10 (successfull) Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2 UniCall/15 <- 0001 [1/ 1/Idle /Idle ] Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2 UniCall/15 Detected Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2 UniCall/15 Making a new call with CRN 32769 Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2...

...irectly to the telco there is no problem, the calls are stablished correctly. Im using the package at: http://www.moythreads.com/astunicall/downloads/ http://www.moythreads.com/astunicall/files/astunicall-1.2.25-0.1.tar.gz that contains: asterisk-1.2.25 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.2.22 My zaptel.conf is this: loadzone=mx defaultzone=mx span=1,1,0,cas,hdb3 span=2,1,0,cas,hdb3 span=3,0,0,cas,hdb3 span=4,0,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 cas=32-46:1101 cas=48-62:1101 cas=63-77:1101 cas=79-93:1101 c...

...take note of the timestamp, you'll find that in some call, it already contradict what the carrier claims but they too have logs to counter my claim. So, I hope people, please give me a good insight and direction to resolve this problem. I have the following for my R2 box: unicall-0.0.3pre8 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 spandsp-0.0.2pre25 asterisk-1.2.6 zaptel-1.2.5 wanpipe-2.3.3-2 2.6.11-1.1369_FC4smp sangoma A101 in my zaptel.conf I got the following: span=1,0,0,cas,hdb3 loadzone = us defaultzone=us cas=1-15:1101 cas=17-31:1101 in my unicall.conf I got these lin...

...stem run success, incoming call and call out are good. when i switch to EWSD (SIEMENS) R-15 . my asterisk faill, cannot connect with EWSD. (E10 and EWSD exchange store in two provinces difference. in Vietnam) this is my logfile of E10 (successfull) Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2 UniCall/15 <- 0001 [1/ 1/Idle /Idle ] Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2 UniCall/15 Detected Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2 UniCall/15 Making a new call with CRN 32769 Aug 17 13:25:38 WARNING[21952] chan_unicall.c: MFC/R2...

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627 unicall_report: MFC/R2 Un...

...e on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or congested, it seems there's no way for Unicall to issue B3 or B4 since its already on accepted state. Please see the log below; May 3 12:51:11 WARNING[11325]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/17 <- 1 on [2/ 2/Group B /Go to grp II ] May 3 12:51:11 WARNING[11325]: chan_unicall.c:2644 handle_uc_event: Unicall/17 event Offered May 3 12:51:11 WARNING[11325]: chan_unicall.c:2699 handle_uc_event: CRN 32782 - Offered on channel 0 (ANI: 09797280105, DNIS: 00151...

Hi list: I want to modify the libmfcr2. But i can't find where is define the end DNIS signal is define. Actually the libmfcr2 send a ONE (1) at the end of sending all the DNIS numbers. I need to send a TWO (2), this becouse in Mexico the normal is to send a 2 at the end, not a ONE. In the next example i dialed un 6 19:12:17 W...

I have a customer that is complaining that any call coming in from Nextel gives a fast busy. We are running Asterisk 1.4.7.1 with Zaptel 1.4.3 and all the MFC/R2 patches and libraries. All other calls go out and come in, just Nextel seems to have this problem. The phone company technician connected a PBX emulator on the line and that one could receive the calls from Nextel. The E1 is provided by Avantel in Mexico City, there are 10 channels available...

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the Asterisk i get at the Nortel only a...

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the Asterisk i get at the Nortel only a...

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but wh...

This is driving me nuts. I'm trying to compile an MFC application using WINE. I can specify the location of the ATL includes and configure is quite happy but it chokes when I give it the MFC includes in the same way: ./configure --with-atl-includes=/home/wade/VC98/atl/Include --with-mfc-includes=/home/wade/VC98/mfc/Include Wassup? I'm using W...

...piled all the required software... The problem is every call (outgoing or incoming) got dropped, complaining about some "T1 timed out" Only for testing purposes I'm using an application called testcall included on the lib-unicall package, and this are the logs: Chan 1, class 'mfcr2', variant 'mx,0,4', end 335544324, caller 1, from '7000' to '6640' Loading protocol mfcr2 Thread for channel 0 MFC/R2 Chan 1: Call control(8) MFC/R2 Chan 1: Unblock MFC/R2 Chan 1: 1001 -> [1/40000000/Idle /Idle ] MFC/R2 Chan 1: far_un...

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and DNIS digits, except for Internati...

Dear Friend Need in Help I created using Application wizard vc++ 6.0 single document interface .... wineg++ -c -mno-cygwin -I. -I/home/khana/mvs6/VC98/mfc/include -I/home/khana/mvs6/VC98/include -o DemoMfc.o DemoMfc.cpp In file included from /home/khana/mvs6/VC98/include/windef.h:166, from /home/khana/mvs6/VC98/include/windows.h:163, from /home/khana/mvs6/VC98/mfc/include/afxv_w32.h:120, from /home...