search for: mail11

Hi guys, I''m setting up asterisk to run with another pbx server. This pbx server support a feature that allows 2 extensions connect to the same FXS. No I put asterisk in the middle. Asterisk receives the call and dial to a SIP/peer. How the pbx installed support 2 extensions to one fxs... How can I figure out in asterisk which extension was dialed before the call came to asterisk?

I should've mentioned that before. I've tried doing that and it has no effect. I've tried both upper and lower-case 'r's. I've also tried a workaround that I thought would work, but it doesn't: Answering the call and then using the playtones(ringing) command before connecting to my cellphone. -----Original Message----- Date: Sat, 1 Apr 2006 19:59:46 +0100 From:

how to adjust voice volume for sipura 2000 and cisco ata186?

i've got a asterisk server running on slackware 10.2 sice 3 weeks, i will upgrade the kernel to 2.6.x from 2.4.x , i will upgrade to the last stable release of kernel... i've got asterisk 1.2.4, zaptel 1.2.4 and libpri 1.2.2, correctly compiled and configured, obviusly if i try to load the new kernel i can't load wtcxx modules, should i recompile zaptel 1.2.4 with make && make

Hi! I have a E1 PRI connected to my TE400P card on span 1, and two channelbanks on span 3 and 4 and * 1.2. Every few hours I get this message and asterisk dies just after that: Warning: No D-channels available! Using Primary on channel 16 anyway! When this happens restarting zaptel and asterisk services, generally puts the system back online my zaptel.con reads: span=1,1,0,ccs,hdb3

Hi i'm planning to migrate a callcenter to asterisk and VOIP, the call center can have up to 25 cuncurrents agents logged in. I'll have some simplty IVR business logic and the some queues. Can a normal server with 1 GB ram 100 GB HDD Pentium 4 3.6 Ghz CPU Ethernet 10/100/1000 Support this? Would you suggest me a particular products? The server and the agents will be in the same LAN,

Hi, I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (only one until now!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR

Does anyone have the polycom soundpoint ip's successfully remotely provisioning? I've got the phone pulling default configs, and it's downloading phone specific information, but it's not actually using that information. Any help would be appreciated :) -- Aaron Daniel Computer Systems Technician Sam Houston State University amdtech@shsu.edu (936) 294-4198

Hello, I have a 4 port FXO digium card with 3 PSTNs attached to it and AsteriskAtHome setup. Everything is working fine except outbound calls. When I dial a outside number, it works fine, but when another employee trys to dial out while I am on a line, it will not go. I have a outgoing route setup in the AMP interface. Dial Pattern: 1NXXNXXXXXX NXXNXXXXXX NXXXXXX Trunk

I wrote a nice detailed post before, and then my mail program lost it for me... so here I go again... I've followed the same process with three different versions of asterisk, my local source copy from about 1 week ago CVS, current CVS from about 24 hours ago, and version 1.0.1, all three versions had identical results: I compiled/installed libpri, zaptel, asterisk I copied config file from

Hello, How do you guys implement LCR in Asterisk? Thanks,

Hi all , I have tried configuring Asterisk at home to make calls outside our Lan WITHOUT any success (Setting up your router/firewall so your remote SIP phones can communicate with your Asterisk@Home Server via SIP through a NAT ) To be precise i did the following (1) I Forwarded UDP Port 5060-5082 to 192.168.1.2 Forward UDP Port 10000 to 20000 to 192.168.1.2 (2) I set

Hi everyone, I am fairly new to the idea of VoIP, although I've been reading about it off and on for the last few years. Now it is starting to look mature enough to consider implementing it, but there is one thing that I haven't been able to get a clear answer on... With Vonage, you are using the Vonage network - it is their responsibility to route your call to the endpoint, which is