search for: kling

You could always run a wireshark on the line and watch the traffic directly. On Thu, May 2, 2019, 3:48 PM Christopher Klinge <Christ.Klinge at web.de> wrote: > I will test this ASAP, but can you elaborate as to why this would happen? > If there is no payload traffic in the VPN, there should be no reason to > query for IP addresses. And if tinc switches do query for addresses without > cause, why would...

...t might look like in the config file? Thanks! On Sun, May 5, 2019 at 6:00 PM Lars Kruse <lists at sumpfralle.de> wrote: > Hello Christoph, > > I am glad, that you discovered the source of the problem! > > > Am Sat, 4 May 2019 08:30:28 +0200 > schrieb "Christopher Klinge" <Christ.Klinge at web.de>: > > > The goal was that all connections between my nodes, regardless of whether > > they are destined for internal or external ipv6 addresses, end up using > the > > VPN. > > This is indeed a bit tricky. > I use a setup with a...

Hi everyone,   I am new to using tinc and currently trying to set up a full IPv6 mesh between 4 servers of mine. Setting it up went smoothly and all of the tinc clients do connect properly. Routing through the network works fine as well. There is however a large amount of management traffic which I assume should not be the case.   Here is a quick snapshot using "tinc -n netname top"

...hence option "1:5" is unparsable root@Delta:~# tc filter add dev ppp0 parent 1:1 classid 1:5 protocol ip Unknown filter "classid", hence option "1:5" is unparsable I don''t understand why it does not work. Can anybody explain me this problem? -- Christoph Kling -- Christoph Kling Christoph-Kling@uni.de _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

I suspect your /64.. try giving a single address to two seperate machine so one single addresses for each. /32 . Then check your traffic. Tinc is a mesh network. If you give it millions of addresses. Then its probably checking each one. On Thu, May 2, 2019, 2:06 PM Christopher Klinge <Christ.Klinge at web.de> wrote: > Good evening, > > all of my servers where set up fresh with no other applications running > besides tinc and my ssh sessions. I just double checked and those are the > two only processes on my machines that have active sockets. Additionally,...

Hello Christopher, Am Mon, 6 May 2019 21:57:09 +0200 schrieb "Christopher Klinge" <Christ.Klinge at web.de>: > shouldn't these two rules work as well? >   > ip route add <remote public ipv6>/64 via 1111:1::1 > ip route add <remote public ipv6>/0 dev<own internet interface> >   > According to my knowledge thus far, linux shoul...

Sound like your tincs are talking to each other over and over. Can we get some info from tinc.conf and tinc host files.. need to see some ip address configs for tinc. On Wed, May 1, 2019, 10:46 AM Christopher Klinge <Christ.Klinge at web.de> wrote: > Hi everyone, > > I am new to using tinc and currently trying to set up a full IPv6 mesh > between 4 servers of mine. Setting it up went smoothly and all of the tinc > clients do connect properly. Routing through the network works fine as &gt...

Hello Christopher, Am Wed, 1 May 2019 12:37:33 +0200 schrieb "Christopher Klinge" <Christ.Klinge at web.de>: > There is however a large amount of management traffic which I assume should > not be the case. indeed - I never noticed an unreasonable amount of tinc management traffic with any of my setups. How exactly did you verify, that tinc meta traffic is r...

Hello Christoph, Am Thu, 2 May 2019 19:42:25 +0200 schrieb "Christopher Klinge" <Christ.Klinge at web.de>: > all of my servers where set up fresh with no other applications running > besides tinc and my ssh sessions. Did you try something as simple as "tcpdump -npi TINC_INTERFACE"? This should give you a good impression of the traffic flowing thr...

Hello Christopher, Am Fri, 3 May 2019 20:06:54 +0200 schrieb "Christopher Klinge" <Christ.Klinge at web.de>: > I did some digging, and thus far I could not find any other culprit other > than tinc itself. The packages that are being sent are addressed directly to > the other tinc hosts on their vpn addresses. During my latest tests, within > about 12 se...

Hello Christoph, I am glad, that you discovered the source of the problem! Am Sat, 4 May 2019 08:30:28 +0200 schrieb "Christopher Klinge" <Christ.Klinge at web.de>:   > The goal was that all connections between my nodes, regardless of whether > they are destined for internal or external ipv6 addresses, end up using the > VPN. This is indeed a bit tricky. I use a setup with a similar goal based on IPv4. I solve...

Hello: I hope none of you will mind helping a newbie. I'm a student research assistant working with a large data set in which observations are categorized according to two factors. I'm trying to calculate the group mean and variance of a variable (called 'hsgpa' in the example data presented below) to each observation , excluding that observation. For example, if there are

On Sun, Aug 25, 2019 at 02:41:03PM +0200, Christopher Klinge wrote: > I am trying to run tinc version 1.1pre17 on fedora 30 hosts and I am running > into a problem. Building and starting tinc works just fine. [...] > However, the hosts cannot connect to each other. When checking the logs, the > following appears over and over again, for any com...

Hello list. I just installed and configured my first Samba-3 PDC and I succeeded immediately with the "join" operation with a Win2k SP4 client. As I afterwards rebooted and tried to logon with the domain user, both root and regular user, I got an error messagge telling me that it was unable to create \\servername\root\profile.pds. In fact, my /home/profiles directory remains empty (no