Displaying 7 results from an estimated 7 matches for "isp0".
Did you mean:
esp0
2008 Oct 14
1
FreeBSD 7-STABLE, isp(4), QLE2462: panic & deadlocks
...info) - Battery temperature is normal
mfi0: 3317 (boot + 68s/0x0008/info) - Battery started charging
mfi0: 3318 (boot + 68s/0x0008/info) - Current capacity of the battery is above threshold
mfi0: [ITHREAD]
pcib8: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci10: <ACPI PCI bus> on pcib8
isp0: <Qlogic ISP 2432 PCI FC-AL Adapter> port 0xdc00-0xdcff mem 0xfc5bc000-0xfc5bffff irq 16 at device 0.0 on pci10
firmware_get: failed to load firmware image isp_2400
isp0: [ITHREAD]
isp0: Board Type 2422, Chip Revision 0x3, resident F/W Revision 4.3.1
isp1: <Qlogic ISP 2432 PCI FC-AL Adapte...
2012 Sep 27
1
CAM Target Layer and Linux (continued)
...eservation information start:
CTL Persistent Reservation information end
CTL Frontends:
Frontend CTL ioctl Type 4 pport 0 vport 0 WWNN 0 WWPN 0
Frontend ctl2cam Type 8 pport 0 vport 0 WWNN 0x5000000995680700 WWPN 0x5000000995680702
Frontend CTL internal Type 8 pport 0 vport 0 WWNN 0 WWPN 0
Frontend isp0 Type 1 pport 0 vport 0 WWNN 0x20000024ff376b98 WWPN 0x21000024ff376b98
isp0: max tagged openings: 4096, max dev openings: 4096
isp0: max_ccbs: 20488, ccb_count: 79
isp0: ccb_freeq is NOT empty
isp0: alloc_queue.entries 0, alloc_openings 4096
isp0: qfrozen_cnt:0:0:0:0:0
(ctl2:isp0:0:0:0): 0 requests...
2003 Dec 18
0
Partial deadlock in 4.9p1
...baseTX-FDX, auto
tlphy0: <ThunderLAN 10baseT media interface> on miibus0
tlphy0: 10base2/BNC, 10base5/AUI
pci0: <ATI Mach64-GV graphics accelerator> at 8.0
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 9.0
pci0: <unknown card> (vendor=0x114f, dev=0x0004) at 13.0 irq 5
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x2c00-0x2cff mem 0xc6afc000-0xc6afcfff irq 15 at device 15.0 on pci0
fxp0: <Intel 82559 Pro/100 Ethernet> port 0x3000-0x303f mem 0xc6b00000-0xc6bfffff,0xc6afb000-0xc6afbfff irq 15 at device 16.0 on pci0
fxp0: Ethernet address 00:d0:b7:20:bd...
2001 Nov 01
2
Internal Network Routing
...establish it (Network unreachable).
The other hosts are configured with an default gateway
192.168.1.4 and have no such problems.
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif
Expire
default 0.0.0.1 UGSc 2 7 isp0
0.0.0.1 0.0.0.0 UH 1 0 isp0
127 127.0.0.1 UGSc 0 0 lo0
127.0.0.1 127.0.0.1 UH 1 0 lo0
192.168.1/28 link#1 UC 0 0 rl0 =>
192.168.1...
2010 Feb 22
2
Load balance outgoing calls
Hello everybody.
I have a provider that has 3 asterisk boxes which I must balance my
calls against. At the moment, I route different destinations to
different boxes but this causes lots of problems.
Without resorting to OpenSER or other proxies (as my provider also
uses IAX), is there a way I can load balance outgoing channels in
Asterisk?
For example an IAX peer like:
[iax_provider]
type=peer
2004 Aug 12
0
Advanced Routing and FreeSwan
...GP SIGNED MESSAGE-----
Hash: SHA1
Hello,
I''m trying to setup a central IPSEC-Gateway with several ipsec tunnels.
Some are to be routed over one leased line, some over the other leased
line. Both leased lines have their own public ip adress.
The setup looks kinda like this:
eth1(ipsec0)--ISP0--Internet--eth1-Linux1-eth0--Subnet1
/
(ipsec-tunnel0)
Intranet--eth0-Linux-HQ
\
(ipsec-tunnel1)
eth2(ipsec1)--ISP1--Internet--eth1-Linux2-eth0--Subnet2
I wanted to use the advanced routing features (ip command) of the linux
kern...
2003 Sep 29
2
4.9-RC and bge
Recent SUP.
Installed on Dell PowerEdge 4600.
Getting tons of:
Sep 30 12:23:16 zige /kernel: bge0: gigabit link up
Sep 30 12:23:46 zige last message repeated 98 times
Also getting some TCP retransmits. This causes noticable delays in
pretty much everything I do now. Not a problem prior to the SUP.
I was on 4.8-STABLE before.
When pulling/replacing cables, it went into a mode where it would