search for: iax

I have an issue where * tries to route a call over IAX to another server even if the server is down. I have included the relevant entries from my iax.conf, extensions.conf, and some debug output. If someone could tell me what I have configured incorrectly, I would appreciate it. Thanks, Stephen -----------iax.conf on voip2---------- [voip1] type...

I'm having some trouble with placing some iax calls over an openvpn: Setup A is a 1.8GHz Celeron, T100P attached to a Zhone Zplex. Setup B is a 266MHz P2, T100P attached to a Zhone Zplex. Setup C is a 700MHz P3, T100P attached to an Adtran TA 750. Setup D is a 233MHz Pentium, with an X100P. Setups A and B are on the same physical network. I...

...it set up as a mutual friend with another one (in another state... about 150ms away). Calls between the two fail to get established approximately 50% of the time. When a call works, everything is fine. When one fails, however, I see a large number of 'VNAK' and 'INVAL' messages from iax debug, and the call is never connected. I think that our contexts, usernames, and secrets are set up all right, since calls do go through just fine part of the time. My machine also registers reliably with the other machine, and we have had the same problem with a non-dynamic host declaration...

Hi I've 3 iax connections to my provider , each of them have own DID , PH1<----| | \/ PH2<-->|-----| <---------------------------> |----|<-- DID1 | A1 | <---------------------------> |ISP |<-- DID2 PH3<-->|-----| <---------------------------> |----|<-- D...

Dear Members, I am trying to make call from one Gnophone to another through the local Asterisk Server.All the three systems have local IP Addresses I created two users "sheeba" (extension 600) and "test" (extension 602) in iax.conf file: [sheeba] type=friend auth=plaintext host=dynamic secret=sheeba context=default allow=gsm permit=0.0.0.0/0.0.0.0 callerid="sheeba"<600> [test] type=friend auth=plaintext host=dynamic secret=test allow=gsm context=default permit=0.0.0.0/0.0.0.0 callerid="test"&l...

...--Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Tony Hoyle Sent: Monday, August 15, 2005 7:42 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Voipbuster blocking Asterisk/IAX connections? Erick Weber V. wrote: > For me to > Works for me... Tony _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists....

hallo, i am really confused how nativ briging is working with asterisk, i use a asterisk server as central server and register another asterisk and an iaxcomm client to the server, all three have public ips on the internet. somtimes, when i call from iaxcomm to my asterisk, the calls go peer to peer (i can see it with tcpdump) but sometimes the get routed through the central asterisk server on the net. i dont change anything in the configs and i...

I had a working 1.0.9 asterisk installation and tried to get a Firefly IAX phone to register, but it was failing. I upgraded to asterisk 1.2.5 and the PBX is working fine, but the IAX phone still won't connect. Below is my iax.conf and the output from setting iax2 debug while the phone tries to connect. Could somebody please give me some pointers? This doesn...

Hi All, I am having trouble with receiving calls from FWD via IAX. I know this isn't a FWD support forum, but I suspect the problem is my asterisk setup. The problem is that I can dial out to fwd subscribers, even myself but they can't dial me using my FWD number. I don't know much about IAX, but it would seem to me like a registration problem, b...

I saw this thread which is very similar to my issue, though I cannot solve mine with iptables. http://lists.digium.com/pipermail/asterisk-users/2013-September/280429.html Using asterisk 11.5, IAX does not seem to be able to receive any packets. My IP tables looks like this: root at dlaptop:/home/darryl# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination...

Hello I have created an iax exten in my iax.conf file: [300] type=friend username=300 secret=*** context=default host=dynamic callerid="some name" <300> auth=md5 Then in my extensions.conf I have: exten => 300,1,Dial(IAX/${EXTEN},20) exten => 300,2,Hangup I can dial from iaxComm (a soft IAX client) a...

I am attempting to use an IAX2 channel between two Asterisk systems. This would seem to be a normal thing to do. I actually want to trunk traffic between the two that are in remote locations. However, I have started with what I think is a simple configuration, which should allow for one way calling. Attached are the pertinen...

...sterisk" <junk@lexon.ws> To: <timebandit001@gmail.com>; "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Monday, February 21, 2005 12:29 PM Subject: Re: [Asterisk-Users] Conecting to asterisk server through NAT usingIAX >I did change the port 4569. > Also my router forwards those packets. > > If I start tcpdump port 4569 on my server I receive: > > 04:25:36.061292 IP 192.168.1.253.4569 > beu164.neoplus.adsl.tpnet.pl.4569: > UDP, length 24 > 04:25:39.154871 IP beu164.neoplus.adsl.tpnet....

Dear all i'm trying to originate an outgoing call with the command originate, from Asterisk's CLI i'm typing: CLI> originate IAX2/my-iax-provider/number2call application wait 10 [Apr 18 19:31:12] DEBUG[32331]: chan_iax2.c:4000 create_addr: prepending 40 to prefs -- Call accepted by 62.149.202.150 (format ilbc) -- Format for call is ilbc -- Hungup 'IAX2/my-iax-provider-5647' ... and nothing happend.... th...

I'm new to this list, and I apologize if this is an already answered question, but my Google-fu was not strong enough to find the answer if it was. I'm having a problem with DTMF on incoming IAX calls. For the first few seconds of the call (between maybe 1 and 15, it varies from call to call) everything works fine. After that I continue get DTMF_E messages from the remote IAX server and continue to send back ACKs, but the tones stop being processed. Everything seems to work fine from...

Hi All! I have two [*]s, and both work OK as a simple local PBX. Now, I try to link them using IAX. Let's call those babies a1 and a2. From a1, I want to dial a phone connected to a2. Both boxes have a fixed IP address, and use standard port 5036, say a1.mystrx.com and a2.mystrx.com. Where I (obviously) get confused, is when it comes to inbound, outbound, registration, etc. Taking a hint...

Hi All, I'm having problem with IAX, I'm trying to connect to speex.co.il from asterisk using: register => username:password@speex.dyndns.org and I cant get it to work. Maybe someone who already got this to work will help... When dialing my speex extension I see the next output from consol: IAX2 Debugging Enab...

Hi, all I am still battling to connect * and voipbuster. What protocol does it use? Ethereal capture shows UDP traffic, but no SIP or IAX traffic when using their client. VoipBuster client connects to connectionserver.voipbuster.com on port 11112 for authentication. Call itself is placed on different server. I have tried to connect using SIP and IAX and it seems that no authentication is happening. (i was trying to use sip.voipbu...

Hi, I am setting up a small call center using *. I have ZAP setup for incoming calls and IAX setup for agents. Agents login using AgentCallbackLogin. When customers call, it's getting picked up and when queue is trying to call back the agents, I am getting error. I am using CVS HEAD, and updated just now. The error is: -- Executing Answer("Zap/1-1", "") in n...

Greetings, DIAX seems to work well placing calls, but I can't actually receive a call . Here, DIAX (x305) "registers", then I use a sip phone to place a call to DIAX (which definitely is not in use by me at debug time, but it is idle on my desktop.I think), and then * goes to vmail. Here's the...