search for: hostadapt

...gic_ProbeOptions.LimitedProbeISA ? BusLogic_ProbeOptions.Probe330 : check_region(0x330, BusLogic_MultiMasterAddressCount) == 0)) { + if (PrimaryProbeInfo->IO_Address == 0 && + (!BusLogic_ProbeOptions.LimitedProbeISA || + BusLogic_ProbeOptions.Probe330)) { PrimaryProbeInfo->HostAdapterType = BusLogic_MultiMaster; PrimaryProbeInfo->HostAdapterBusType = BusLogic_ISA_Bus; PrimaryProbeInfo->IO_Address = 0x330; @@ -805,15 +807,25 @@ static int __init BusLogic_InitializeMul omitting the Primary I/O Address which has already been handled. */ if (!BusLogic_Probe...

...gic_ProbeOptions.LimitedProbeISA ? BusLogic_ProbeOptions.Probe330 : check_region(0x330, BusLogic_MultiMasterAddressCount) == 0)) { + if (PrimaryProbeInfo->IO_Address == 0 && + (!BusLogic_ProbeOptions.LimitedProbeISA || + BusLogic_ProbeOptions.Probe330)) { PrimaryProbeInfo->HostAdapterType = BusLogic_MultiMaster; PrimaryProbeInfo->HostAdapterBusType = BusLogic_ISA_Bus; PrimaryProbeInfo->IO_Address = 0x330; @@ -805,15 +807,25 @@ static int __init BusLogic_InitializeMul omitting the Primary I/O Address which has already been handled. */ if (!BusLogic_Probe...

I used to use a hot-plugable PATA-CDROM drive on my Computer (Samsung P35 laptop). To change drive I use a script which at the bottom of its heart uses Code: echo "scsi remove-single-device 1 0 0 0" | sudo tee /proc/scsi/scsi and Code: echo "scsi add-single-device 1 0 0 0" | sudo tee /proc/scsi/scsi commands in oder to let the OS being aware of the changed drive. This

Hi Andi, This is a set of updates for the firstfloor patch queue. Quick rundown: revert-mm-x86_64-mm-account-for-module-percpu-space-separately-from-kernel-percpu.patch separate-module-percpu-space.patch Update the module percpu accounting patch fix-ff-allow-percpu-variables-to-be-page-aligned.patch Make sure the percpu memory allocation is page-aligned

Hi Andi, This is a set of updates for the firstfloor patch queue. Quick rundown: revert-mm-x86_64-mm-account-for-module-percpu-space-separately-from-kernel-percpu.patch separate-module-percpu-space.patch Update the module percpu accounting patch fix-ff-allow-percpu-variables-to-be-page-aligned.patch Make sure the percpu memory allocation is page-aligned

Hello, I have the subject mentioned mb and I am trying to install centos 4.4 with sata raid enabled, but linux is not seeing the drives? I tried to load via sata raid driver, no luck there. I guess I could try legacy mode in the bios, but I was hoping there is another way around to load linux with the raid? Thanks....

...list has similar experiences, or maybe even a possible solution. My setup is a dual PIII-750 with 1 gig of RAM, with an X100P, connected to an analog line to my telco, and a TDM40P with analog phones connected. The TDM-card is not sharing any interrupts, but the X100P is, with the 2 Adaptec SCSI hostadapters on the mainboard. There's only a tapestreamer on one of them, though, and it's mostly idle, as I only use it during backups. Not loading the SCSI-drivers at all doesn't make any difference in the problems below. All of the disks in the machine are IDE, and those controllers have the...

...RC6/E card. DELL 6/I control 5 internal disks. The original disk sequence are: /dev/sda1 /boot /dev/sda2 / /dev/sdb1 swap ... after I configured PERC6/E disks and reboot, /dev/sda change to RAID disk and original /boot and / change to /dev/sde1 and /dev/sde2. My modprobe.conf is: alias scsi_hostadapter megaraid_sas alias scsi_hostadapter1 ata_piix alias eth0 bnx2 alias eth0.1998 bnx2 alias eth1 bnx2 how to change sequence back? Thanks. ______________________________________________________________________________________________________ ?????????Yahoo!??????2.0????????????? http://tw....