search for: forceloads

...system module load paths and attempts to match module names with pseudo drivers to locate the providers, so it will match not only for the dtrace providers in, say /platform/sun4u/mykernel/..., but also for the "originals" in /kernel/... It''s no big whoop, as the additional forceloads just result in warning messages, but it was nice to find out where it was coming from. Check out: http://cvs.opensolaris.org/source/xref/usr/src/lib/libdtrace/common/dt_open.c#757 for the gory details. --S

Hi All, One of the customer is seeing the following error messages. He is using a S10U1 system with all latest patches. Dtrace script is attached. I am not seeing these error messages on S10U2 system. What could be the problem? Thanks, Gangadhar. ------------------------------------------------------------------------ rroberto at njengsunu60-2:~$ dtrace -AFs /lib/svc/share/kcfd.d dtrace:

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

Where can I find a list of supported multipath drivers for ZFS? Keith McAndrew Senior Systems Engineer Northern California SUN Microsystems - Data Management Group <mailto:Keith.McAndrew at SUN.com> Keith.McAndrew at SUN.com 916 715 8352 Cell CONFIDENTIALITY NOTICE The information contained in this transmission may contain privileged and confidential information of SUN

Hello, I''ve done this several times in the past but a co-worker is having problems getting anonymous tracing to work: dtrace -A -m su and we see updated /kernel/drv/dtrace.conf and fbt and dtrace forceloads added to /etc/system. Upon reboot the following errors occur (note that we are running snv_66): {0} ok boot disk Boot device: /pci at 0/pci at 0/pci at 2/scsi at 0/disk at 0 File and args: SunOS Release 5.11 Version snv_66 64-bit Copyright 1983-2007 Sun Microsystems, Inc. All rights reserved. U...

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

I define [globals] myvar = ${DB(store/myvar)} --- But when I want to use ${myvar} in the dial plan, I found that the variable is null when Asterisk is restarted. Only a reload would force globals to read AstDB. Other variables in globals loads fine. Any idea? (Asterisk 1.2.13) Yuan Liu

2010/12/1 Shaun Ruffell <sruffell at digium.com> > On 12/01/2010 11:00 AM, Shaun Ruffell wrote: > > On 12/01/2010 09:56 AM, Olivier wrote: > >> I'm facing an issue with which loading wctdm24xxp module fails. > >> [ 33.527942] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive > frame. > >> [ 33.527995] wctdm24xxp 0000:01:0b.0: The firmware

I have a question about getting PCIe advanced error reporting to work on 5.5. The info I need to start with is the following: 1) Is PCIe Advanced Error Reporting (including error injections) known to work in 5.5? 2) What configuration options do I need to select in order to enable it? I'm using the following configs: CONFIG_ACPI=y CONFIG_PCI=y CONFIG_PCI_DIRECT=y CONFIG_PCI_MMCONFIG=y

Hello, on a v20z, we have as DOM 0 a Solaris XEN on snv44 64bits and we have as DOM U a Solaris XEN on snv44 64 bits. We then install a pseudo driver in the Solaris DOM 1 XEN snv44: installation is ok and driver works as expected. But on reboot of DOM 1, the driver is no more there (in modinfo, driver not found). Is there something special to do after a pseudo driver installation in a Solaris

Hello all, It was often asked and discussed on the list about "how to change rpool HDDs from AHCI to IDE mode" and back, with the modern routine involving reconfiguration of the BIOS, bootup from separate live media, simple import and export of the rpool, and bootup from the rpool. The documented way is to reinstall the OS upon HW changes. Both are inconvenient to say the least.

I've been working on a fairly complex package that is a wrapper for several optimization routines. In this work, I've attempted to do the following: - edit the package code foo.R - in a root terminal at the right directory location R CMD REMOVE foo R CMD INSTALL foo However, I don't get the right code. In fact, if I just do the remove, library(foo) does not throw an

I''m seeing seriously degraded performance with round-robin SAS multipathing. I''m hoping you guys can help me achieve full throughput across both paths. My System Config: OpenSolaris snv_134 2 x E5520 2.4 GHz Xeon Quad-Core Processors 48 GB RAM 2 x LSI SAS 9200-8e (eight-port external 6Gb/s SATA and SAS PCIe 2.0 HBA) 1 X Mellanox 40 Gb/s dual port card PCIe 2.0 1 x JBOD:

Hi, I have a faulty dtrace script (most probably too big bufsize). My machine hangs at boot (amd64 5.10 Version Generic_118855-10 64-bit). NOTICE: enabling probe 11 (dtrace:::ERROR) WARNING: /etc/svc/volatile: File system full, swap space limit exceeded WARNING: Sorry, no swap space to grow stack for pid 5 (autopush) WARNING: /etc/svc/volatile: File system full, swap space limit exceeded How to

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hello Everyone,   Learning about R and its wonderful array of functions. If it's not obvious, I usually try to find out what a function stands for. I think this helps me remember better.   One function that has me stumped is "sink." Can anyone tell me if this stands for something?   Thanks,   Paul         __________________________________________________ [[alternative HTML