search for: firmawar

...other prism card but prism2 and that card work very well but with a lot lower power and more noise because I need use an Ampl. With The prism2.5 the Access point work so good , we have customers close of 27km, until the wireless card crash and I need restart it . at this moment I tried with the firmaware 1.4.9 and 1.5.6, I didn't tried yet with the 1.7.4 path, firmaware????? any idea?? Marcos Biscaysaqu Systems Administrator ThePacific.Net Ltd.

I have a prism 2.5 firmaware 1.5.6 but I can't make work this in 11Mbps on Freebsd 5.1 but the same card work perfect in Freebsd 5.0 help pls! this is my ifconfig wi0:flags=8947<UP,BROADCAST,DEBUG,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:60:b3:7a:a3:1d media: IEEE 802.11 Wireless Ether...

...le ISDN cards ii libcapi20-3 3.9.20060704-1 libraries for CAPI support ii libcapi20-dev 3.9.20060704-1 libraries for CAPI support ii avm-fritz-firmware-2.6.17-10 3.11+2.6.17.7-10.1 Firmware for AVM Fritz! ISDN hardware* and downloaded firmaware from * ftp://ftp.in-berlin.de/pub/capi4linux/firmware/b1/ .*My capi.conf is: *b1pci /usr/share/isdn/b1.t4 DSS1 - - - - P2P* Then I exec command capiinit start, I have noting on output, but it load modules: *root@asterisk:~# lsmod Module Si...

...Suppression: No Yes Voice Frames per TX: 2 (up to 10/20/32/64 for G711/G726/G723/other codecs respectively) // did not try Layer 3 QoS: (Diff-Serv or Precedence value) // 48 Layer 2 QoS: 802.1Q/VLAN Tag 802.1p priority value (0-7) /0 0 I'm using the 1.0.5.16 firmaware, and was using the buggy 1.0.5.21 My asterisk is working fine with about 8 SIP and IAX2 providers using any codecs ... (also the 723) I'm using about 1 month old Asterisk from the CVS. Any comments would be appreciated.

Hello, I am not too familiar with the settings in our PIX (learning though). Here is the only access-list setting that we have in place for Asterisk: access-list acl-prod permit udp any host EXTERNAL_*_IP_HERE eq 5060 In rtp.conf we are allowing ports 10000 - 20000. We are not using SIP Fixup in our PIX due to firmware version. How do I go about adding the ability for udp ports 10000 - 20000

...in> Add to Address Book To: "Seshu Kanuri" <seshukanuri@yahoo.com> CC: mandarpise@yahoo.com Subject: Re: STUN server settings Date: Tue, 20 Jul 2004 20:30:26 +0530 Dear Mr. Seshu Kanuri, Thanks for your mail. D'Link Phones DPH80 and DPH100 are now fitted with the firmaware changes desired by you. Now these phones do not hangup or un-register after 30 seconds. However please note the following. 1. D-Link IP Phones do not have any settings for the STUN server. 2. D-Link (SIP + H.323) Server has in-built STUN functionality support. 3. If one uses this D-Link Server th...

after rebooting I get very often: ... mfi0: COMMAND 0xffffff800132d990 TIMEOUT AFTER 659 SECONDS mfi0: COMMAND 0xffffff800132d990 TIMEOUT AFTER 689 SECONDS mfi0: COMMAND 0xffffff800132d990 TIMEOUT AFTER 719 SECONDS ... another reboot usualy fixes this. danny

...remove that exact same SSD, drop it into an external USB 3.0 2.5" drive case and _then_ try to boot from it, that also chokes. So it seems pretty clear to me that Gigabyte has snafued something, perhaps so seriously so that even the best SYSLINUX may not be able to overcome the (botched) BIOS firmaware. But we'll see. Regards, rfg

In message <BLU0-SMTP557B92590B4CC34F8318088BB30 at phx.gbl>, Ady <ady-sf at hotmail.com> wrote: >Since in all cases you get to see at least the Syslinux copyright >message, the problem doesn't seem to be related to whether your BIOS >can identify the USB disk and boot from it. I can only agree. >Some GA motherboards might identify some USB drives as