search for: etherlink

...nged to UP xl1: watchdog timeout xl1: link state changed to DOWN xl1: link state changed to UP xl1: watchdog timeout xl1: link state changed to DOWN xl1: link state changed to UP --------------------------------------------- xer:/root# cat /var/run/dmesg.boot | grep xl xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec00-0xec7f mem 0xfceffc00-0xfceffc7f irq 23 at device 11.0 on pci2 miibus0: <MII bus> on xl0 xlphy0: <3c905C 10/100 internal PHY> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: Ethernet address: 00:01:02:e0:04:1b xl1: <3Com 3c905C-TX Fas...

...nstalls nicely, everything on the board is detected correctly and usable. It's just the PCI NIC that doesn't work. If I compile a custom kernel without any network drivers in it, and then kldload if_txp, the following appears (same message on all 4 versions): txp0: <3Com 3cR990B-TXM Etherlink with 3XP Processor> port 0xbc00-0xbc7f mem 0xfdcff000-0xfdcff07f irq 16 at device 8.0 on pci3 txp0: not waiting for boot device_attach: txp0 attach returned -1 If I reboot and load if_nve (on 6.2 and 6-stable), then I get: nve0: <NVIDIA nForce MCP13 Networking Adapter> port 0xdc00-0xdc07...

...ENGINEERING Services: Computer Browser NetBIOS Interface Remote Access Service RPC Configuration Server Workstation Protocols: NetBEUI Protocol TCP/IP Protocol IP Address Adapter: [6] 3Com EtherLink III (3C589D) LAN PC Card Specify an IP address: IP Address: 192.168.42.6 Subnet Mask: 255.255.255.0 Default Gateway: DNS Host Name: hercules...

...y more, you folks may find it useful. http://www.coreyfro.com/~coreyfro/froppy-1.6.1-ex.zip This is a winimage IMA file with the FLP extension for VMWare. It has these dos nic drivers 1. Intel 10/100mbit 2. Intel PCMCIA 10/100 3. 3COM Etherlink III 509 10mbit 4. 3COM Etherlink III 509TP 10mbit (rare) 5. 3COM 905 10/100mbit 6. 3COM 589 PCMCIA 10mbit 7. 3COM 575 PCMCIA 10/100mbit 8. AMD PCI Nic (VMWARE) It is broken, in some respects, becaus...

...seconds, it drops off to 25%, then after abuot 30 seconds, drops off again to close to zero. After some amount of time ( perhaps 30 seconds to a minute ), sometimes the speed picks up again. (following the pattern above ) The two computers are linked via a netgear 100Mb hub. The XP box has a 3com etherlink PCI card ( set to auto sense media / 3c???c ), and the samba box is running a netgear FA311 ( I think I remembered the code OK! ) 100Mbs, which seems to use 100Mbs-HD. I am using Kernel 2.4.20 / Samba ( latest - downloaded yesterday in case this was a samba problem ). I have tried forcing both car...

...mer 0060-006f : keyboard 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 02f8-02ff : serial(set) 0376-0376 : ide1 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(set) 0cf8-0cff : PCI conf1 7000-707f : 3Com Corporation 3c905C-TX [Fast Etherlink] 7000-707f : 00:04.0 7400-74ff : ATI Technologies Inc 3D Rage II+ 215GTB [Mach64 GTB] 7800-780f : Acer Laboratories Inc. [ALi] M5229 IDE 7800-7807 : ide0 7808-780f : ide1 moffe@gere:~# cat /proc/iomem 00000000-0009fbff : System RAM 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM ar...

...condary AD at another campus. This setup seemed to be running as expected. We could see our primary AD DC authenticating requests fine. We could see the secondary AD authenticating requests as well at our second campus. Then we started experiencing bandwidth issues between our campuses. Our metro-etherlink should have delivered 5 mbps but dropped to have very sporadic performance. As we worked with our telecom provider to stabilize this, we thought we might also improve things by using the AD sites and services tool to define where our subnets were and hopefully control which DC handled auth requests...

...-e1ffffff Prefetchable memory behind bridge: d8000000-dfffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: <available only to root> 00:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30) Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2500ns min, 2500ns max), cache line size 08 Interrupt: pin A routed...

...bridge (vendor=0e11 device=0001)> at device 20.0 on pci0 eisa0: <EISA bus> on isab0 mainboard0: <CPQ0551 (System Board)> on eisa0 slot 0 isa0: <ISA bus> on isab0 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xe8000-0xedfff,0xee000-0xeffff on isa0 ep0: <3Com 3C509-Combo EtherLink III> at port 0x320-0x32f irq 10 on isa0 ep0: Ethernet address 00:a0:24:1d:1a:50 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0...

On Tuesday, June 30, 1998 2:25 PM, cmc@mind.org wrote: >Something I'm actually familiar with. Wow. > >First off, the 3C595 card does *not* support full-duplex at 100mb. >It supports 10mb at half or full duplex and 100mb at half duplex >only! I researched this only 2 weeks ago, check on 3com's site if >you're not convinced. Backing off to half-duplex won't fix this

...mba server, to > permit us to download (using "ghost") a disk image to our Dell Optiplexes. > We can seem to get last year's boot disks to load; specifically, netbind > complains that it can't bind, hardware failure. This year's Dells come > with 3Com 3C905b PCI Etherlink cards...last year's model had the 3C905 > version. > > I don't as much as I should about the protocols used in Dos and am at a > loss where to start. The boot disk appears to be loading NDIS LanManager > stuff, starting with > LH net initialize > netbind.com &gt...

...1f irq 10 at device 7.3 on pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: <unknown card> (vendor=0x1106, dev=0x3057) at 7.4 xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xdc00-0xdc7f mem 0xe2000000-0xe200007f irq 11 at device 11.0 on pci0 xl0: Ethernet address: 00:01:03:d0:e9:f6 miibus0: <MII bus> on xl0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl1: <3Com 3c900...

...V) USB controller> on ohci1 usb1: USB revision 1.0 uhub1: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xb400-0xb47f mem 0xe9800000-0xe980007f irq 10 at device 11.0 on pci0 xl0: Ethernet address: 00:50:da:19:cc:b4 miibus0: <MII bus> on xl0 xlphy0: <3Com internal media interface> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto chip0: <AcerLabs M15x3...

...ntroller: Matrox Graphics, Inc.: Unknown device 0527 (rev 03) 02:04.0 USB Controller: NEC Corporation USB (rev 41) 02:04.1 USB Controller: NEC Corporation USB (rev 41) 02:04.2 USB Controller: NEC Corporation: Unknown device 00e0 (rev 02) 02:0b.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 78) 02:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. OHCI Compliant IEEE 1394 Host Controller (rev 46) [vogl /net/home2/vogl]$ cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Pentium(R) 4 CPU 2.40GHz...

...SB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered Timecounter "PIIX" frequency 3579545 Hz chip1: <Intel 82371AB Power management controller> port 0x440-0x44f at device 7. 3 on pci0 xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xec00-0xec7f mem 0xfebfef80-0xfebf efff irq 5 at device 15.0 on pci0 xl0: Ethernet address: 00:01:02:be:6d:85 miibus0: <MII bus> on xl0 xlphy0: <3Com internal media interface> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl1: <3Com 3c905B-TX F...

...uhci0: [GIANT-LOCKED] usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: <bridge> at device 7.3 (no driver attached) xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xa400-0xa47f mem 0xe9020000-0xe902007f irq 5 at device 10.0 on pci0 miibus0: <MII bus> on xl0 xlphy0: <3c905C 10/100 internal PHY> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: Ethernet address: 00:50:da:e2:35:3b pci0: <multimedia, audio&g...

...i1: <Generic PCI ATA controller> port 0xf000-0xf00f at device 9.0 on pci0 ata0: at 0x1f0 irq 14 on atapci1 ata1: at 0x170 irq 15 on atapci1 pcib2: <PCI to PCI bridge (vendor=10de device=006d)> at device 12.0 on pci0 pci2: <PCI bus> on pcib2 xl0: <3Com 3c920B-EMB Integrated Fast Etherlink XL> port 0xc000-0xc07f mem 0xea000000-0xea00007f irq 11 at device 1.0 on pci2 xl0: Ethernet address: 00:26:54:0e:71:f1 miibus0: <MII bus> on xl0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fwohci0: vendor=10de...

i trust i am still new in freebsd, after go through all mail and book, = now seem to be more close, i got 3 server and a notebook to play with, = install no problem. cvsup not problem.make buildworld not problem. make = build kernel become,every machine i got different error code 1,=20 1-one got system full=20 2-one showing this sometime=20 > anyone know the best way to be one time success,not

...1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib2 xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xa400-0xa47f mem 0xeb001000-0xeb00107f irq 11 at device 5.0 on pci2 xl0: Ethernet address: 00:a0:24:48:0c:3f miibus0: <MII bus> on xl0 xlphy0: <3Com internal media interface> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isab0: <PCI-ISA bridge&...

Hi, I'm trying to build a bridge using a 486DX2/66 with two 10 Mbit Ethernet NICs. The machine (tsushima) is running Debian stable and kernel 2.4.26. Previously I used it as a router, so I know the hardware (NICs) is working. The NICs are as follows: eth0: WD80x3 at 0x280, 00 00 C0 0A 2C 2F WD8003-old, IRQ 10, shared memory at 0xd0000-0xd1fff. eth16i.c: v0.35 01-Jul-1999 Mika Kuoppala