search for: ehternet

Hello everyone. What's better for Asterisk: have 2 distinct 100Mb network cards in the system, one on the "internet" and one on the "local net" OR have one 1000Mb network card with 2 separate VLAN's set up? It's a difficult decision because 2 cards are using 2 IRQ's etc but a single 1000Mb card might generate more PCI interrupts and get me into different

...> > I just saw a know bug from wiki that network doesn''t work in guest in > arndale board : > > Network doesn''t work in the guest > > Contact: julien.grall@citrix.com > Status: In progress > Description: Network doesn''t work in the guest when an ehternet cable is > plugged > References: http://pastebin.com/gEP3HdCg > > What''s the latest status? > > best regards > Mail > Any comments? best regards Mail

...t needed to use external instead of USB power for my USB CDrom. Go figure... I did this in my hotel room, where they only have wireless. I went down to the 'business center' and used an ethernet drop, but I don't think the registration worked. I didn't know that even for the ehternet drops you have to do that portal thing with your browser. How do I determine if the registration was completed. Now I am making headway, finally, on the Toshiba Portege 3490. I was having TERRIBLE timing problems with the multiport extender. Then I decided to THINK, and went into BIOS, changed...

Hi, We have a simple bridge setup but the ping (and other network traffic) does not work reliably. After tracing the code, it looks like a software bug. Since bridge software is been running by thousands of people. I guess I am wrong. Anyway, here is the problem. There are 2 boxes and each one has 2 interfaces, 1 ethernet and 1 wifi. STP is enabled for the bridge to avoid the loop. So the box 1

Hi experts I use xen-4.0.0 and dom0 is 2.6.33 and domU is 2.6.34 #lspci ............... 01:00.0 Ethernet controller: Intel Corporation Unknown device 10a7 (rev 02) 01:00.1 Ethernet controller: Intel Corporation Unknown device 10a7 (rev 02) 05:00.0 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06) 05:00.1 Ethernet controller: Intel Corporation 82571EB Gigabit

...ng Quintum Tenor AXT800 VOIP gateway can anyone integrate it with asterisk if anyone what is the scenerio? i have a scenerio which is quite simple but i am confused about it whether it is possible or not : I integrate it with asterisk for intranet no PSTN at all just only IPphones connected through ehternet port and analog phones connected on FXS port.Is it's neccassary to connect with PSTN i don't want PSTN DIALING i'll just internal dialing.the scenerio is ipphones connected through ethernet while analog phones directly connected through FXS port is that possible i integrate Tenor AXT 80...

I am usong three ehternet cards eth0 , eth1 , eth2 and eth0 and eth2 is connected to two diffrent ISP and eth1 is connected to local lan. I am tring to route all the mail traffic to eth1 and I have followed the lartc doc. But it seems the solution does not work for me . is there a way I could connect two diffrent ISP in...

Hi Im very green to asterisk, and I have been asked if asterisk can be used to do remote control, like opening gates etc, say when the user dials a predefined number ... And what hardware is required ... Many Thanks -- Gregory Machin gregory.machin@gmail.com www.linuxpro.co.za

Hi I want to block the IP traffic between any 2 hosts on a switched ethernet LAN. Will setting all the possible IP addresses on a linux machine in the LAN do the trick or there is another easier solution? -- Anton Glinkov network administrator _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

Hi there, I'm trying to set up a man-in-the-middle scenario within a VMWare Workstation team, using brctl. What I want is the following: PC1 eth0 >---LAN-segment-1---< eth0 PCMITM eth1 >---LAN-segment-2---< eth0 PC2 Now I did the following on PCMITM (PC man in the middle): ifconfig eth0 down ifconfig eth1 down brctl addbr lnxbr0 brctl addif lnxbr0 eth0 brctl addif lnxbr0 eth1

...-testing make world ( The first compilation show now errors and build all kernels. ) cd linux-2.6.11-xen0 make clean make ARCH=xen menuconfig ( Now I do only this changes ) X86 Processor Configuration -> Prozessor family -> ( Athlon / Duron / K7 ) Device Drivers -> Networking Support -> Ehternet (10 or 100Mbit) <*> Reverse Engineered nforce Ethernet support ( EXPERIMENTAL) The other driver e.g. Intel, Realtek, which enabeled by default did I had disabled. Now exit and save the new configuration. In the directory linux-2.6.11-xen0 I start the building with make ARCH=xen The Prozess st...

...==== 2016-01-16 18:45:15 err infoclinik daemon smbd [2016/01/16 18:45:15.496204, 0] ../lib/util/fault.c:78(fault_report) 2016-01-16 18:45:15 err infoclinik daemon smbd [2016/01/16 18:45:15.496204, 0] ../lib/util/fault.c:78(fault_report) As well as I understand, the problem may be in ehternet-adapters of notebooks... but how to understand the exact point of problem? Maybe some samba network-related settings? Thanks a Lot. Alexander.