search for: dl180

A customer is looking to replace or augment their Sun Thumper with a ZFS appliance like 7320. However, the Thumper was used not only as a protocol storage server (home dirs, files, backups over NFS/CIFS/Rsync), but also as a general-purpose server with unpredictably-big-data programs running directly on it (such as corporate databases, Alfresco for intellectual document storage, etc.) in order to

Hi. I'm using GlusterFS v1.3.12 (glusterfs-1.3.12.tar.gz) via FUSE (fuse-2.7.3glfs10.tar.gz) on CentOS 5.2 x86_64 (Linux kernel 2.6.18-92.el5) now. The nodes are HP Proliant DL360 G5 (as GlusterFS Client) and DL180 G5 (as GlusterFS Servers). And the connections are all TCP/IP on Gigabit ethernet. Then, I tested self-heal and I found a technical problem about "replace" -- self-heal after a node's fault and others' file-contents decreasing leaves garbage. I would like you to show me ideas to...

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subs...

Hello everyone, This is not directly related to CentOS but still: we are trying to set up some storage servers to run under Linux - most likely CentOS. The storage volume would be in the range specified: 8-15 TB. Any recommendations as far as hardware? Thanks. Boris. -------------- next part -------------- An HTML attachment was scrubbed... URL:

I had to install C5 on a dev server for various reasons (legacy system support and so forth). This dev server is a HP DL180 G6, with a SmartArray P410 raid card... I've installed hpacucli via the RPM from HP's site, but its not finding the controller... C5 (64 bit) is using the default CCISS drivers for this card. # hpacucli ctrl all show config Error: No controllers detected. lspci -v reports... 06...

...much better. The only problem (?) I''m still seeing is a warning that seems to occur from time to time: [87703.784552] ------------[ cut here ]------------ [87703.789759] WARNING: at fs/btrfs/inode.c:2103 btrfs_orphan_commit_root+0xf6/0x100 [btrfs]() [87703.799070] Hardware name: ProLiant DL180 G6 [87703.804024] Modules linked in: btrfs zlib_deflate libcrc32c xfs exportfs sunrpc bonding ipv6 sg serio_raw pcspkr iTCO_wdt iTCO_vendor_support i7core_edac edac_core ixgbe dca mdio iomemory_vsl(PO) hpsa squashfs [last unloaded: scsi_wait_scan] [87703.828166] Pid: 929, comm: kworker/1:2 Tainted:...

Hi, I just received a new server (HP DL180G5) with 12x 1TB HDs and I bumped into fdisks 2TB limits... Since this is an entry level server, I can't use the classic HP bootable utilities to create smaller volumes et can only create a big RAID6. I found out that: using parted, labelling it gpt and creating the partitions would do the trick...

Hello, I'm a newbie so here's my question. I'm trying to install CentOS 6.5 on a HP Proliant 350e server. This server has 4x 1TB hard drives. I'd like to enable the hardware RAID 5 and stripe all 4 disk into one 3TB logical volume. Then install CentOS on the 3TB volume. However after I install I can't get the server to boot. I know about the MDOS vs GPT labeling issue.

Hello, I try to create some kind of mail backup system. What I need is system that will store mail for the whole domain, and allow me to restore messages from/to specified email at that domain. The scheme is pretty simple: on our main mail server the SMTP server itself has a rule to send a copy of every message to 'backup at backupserver.host', and the backupserver.host domain is

...176? ? ? ?11? ? ? active sync set-B? ?/dev/sdl We've tried changing the I/O scheduler, queue_depth, queue_type, read-ahead, etc, but nothing has helped. We've also upgraded all of the firmware, and installed HP's mpt2sas driver. We have 4 other Kafka clusters, however they're HP DL180 G6 servers. We completed the same CentOS 6.5 -> 7.2/Kafka 0.8 -> 0.9 upgrade on those clusters, and there has been no impact to their performance. We've been banging our heads against the wall for a few weeks now, really hoping someone from the community can point us in the right directi...