search for: budgettone

Checking the earlier mails, it stated that the phones were $75 (100) & $85 (102) ref :- http://lists.digium.com/pipermail/asterisk-users/2003-June/013483.html Well, I just called Ovislink/dgtimes and was quoted $90 & $100 and the person said there was no price change. Anyone on this list actually bought them at the $75 & $85 rate ??? Regards...Martin -- Too much is just enough.

hi, can someone who has used Budgettone phones tell me how to do the following: an incoming call comes in and is answered by the receptionist. she need to put the call on hold, speak to whoever the call is for, and either (after that) pass on the call, otherwise speak again to whoever was on the call and hang up .. so far i've got...

hi there .. I asked sometime ago regarding getting a Budgettone working with Asterisk over G729. My system is quite simple, Asterisk server with 1 G 729 license installed, and 10 Grandstream phones. Only one of them needs G729, because it's on a remote link via an ADSL bridge. The rest run happily on G711 on a local network. I added the lines disallow=al...

Just got my new Budgettone phone, and I've got a couple of issues. Most important, it doesn't seem to be querying for the time via NTP. I put a sniffer on the line, and once it boots up the only outbound traffic it generates is an attempt to contact a TFTP server, which is programmed in as 192.168.0.168. . . Mu...

--- "Chandra" <chandra@digital.com.np> wrote: >i have been using grandstream budgettone IP phones and they work fine >except that these phones times out after some hours.. i ahve seen that >the phones working ok are next day unregistered and sip show peers do >not show their IP and although these phones can make calls , they >cannot be called. They Sip show peers only show...

Hi there! I installed the BudgetTone (GrandStream) on my LAN without any problems. Then, I moved it to another location using a D-Link NAT. I opened 5060 (SIP) and 5000 to 5008 for RTP. I also fixed the IP address of the BudgetTone. When I receive a call on my Asterisk, it would ring my FXS as before. However, after I pick up, it han...

[Posted here becasue your mail server is rejecting my direct reply to you.] Hi Martin, AFAIK SIP can run on both UDP and TCP but I have only seen it used over UDP.. :) To setup the GS phones you need to open up the following ports (If its still set at the defaults)... UDP/5060 UDP/5004 UDP/5005 UDP/5006 UDP/5007 I have not tested the GS phone through a firewall yet but this config should

Since the last firmware upgrade we've been experiencing some odd CallerID behaviour. Instead of the LCD showing the calling party's #, the phones are showing the internal extension being dialed. This is probably a really stupid fix I'm overlooking, but I was hoping someone could offer some insight. Thanks! -Corey -- Corey S. McFadden McFadden Associates - Technology

Hi all, I'm quite new on this mailing list, and I discover the asterisk world. I m experimenting a PBX with SIP phones, grandstream budgetone (not expensive for tests) All the features I need work just not one : the supervised call transfers. I know there are a lot of posts about that, but none gave me the correct answer (unless I missed it). Here is my config : 2 sip phones BT102 with

I have my new phone mostly working. I do have a couple of residuals that I cannot find mentioned in the list archives: 1. Is it possible to set the volume in these things? I hope I didn't miss it, but I've looked in the doc, the FAQ, and the asterisk archives and don't find anything. The displays in the pictures all have more bars on them than my phone does, and I need a bit

I upgraded from RC2 last night, but have a major call quality issue. Heres our setup: 1 FXS and 1 FXO card. Incoming/Outgoing calls via IAX trunking from our provider. G729 running between us and the VoIP provider. Two handsets, one BudgetTone 102 and a Cisco 7940G running the 7.2 SIP firmware. Both these phones are using ULAW to the server, and we have plenty of G729 licenses on the server. Now the BudgetTone does not have any problems at all. The Cisco however has severe breakup on the incoming audio from the VoIP provider. The calle...

Hi Just recieved the above phone Does anyone have sip.conf and extension.conf example for the SIP phone working with the FXS w100p and the FXO tdm400d any help would be appreciated Thanks Robb

well .. good news :) i've just put in txgain=1.0 rxgain=1.0 in my zapata.conf and upgraded the Grandstream Budgettones i'm using to version 81 of the software and all seems fine .. there is still an echo but after the first couple of seconds of call it vanishes, as the echocancelling kicks in .. so far my client is happy :) now .. i have one slight problem left .. although most of my SIP phones are on a LAN c...

I have an asterisk installation at a client, it's quite simple. Basically it's an asterisk downloaded from CVS about a week ago, with 3 Zaptel FXO cards (the digium ones) and 10 Grandstream Budgettone SIP phones ... Every now and then, especially when a call is ringing and not picked up immediately, Asterisk quits with a segmentation fault error. IT seems quite inexplicable, my dialplan is a modification of the sample one that came with Asterisk, and I haven't touched that many other conf f...

...ave read the information on echo and SIP in the FAQ and I have scoured the mailing list for possible solutions, but as yet I have not been able to get rid of this echo. I have a Sip phone, Digium 4 Port FXS, and 3 Digium FXO cards installed into an asterisk server. If I call between the Sip Phone (Budgettone-100) and the 4 FXS ports everything sounds great. If I call out to the PSTN through the FXO cards I get horrible echo, I have even been able when talking loud enough to get a horrible feedback loop going. I have tried 4 different echo cancellers in the Makefile for the Zap drivers and nonoe of them...

Hi- I am attempting to setup my Budgettone phone for use with my * server and am having problems obtaining an IP address. I have checked the phones settings to make sure it has dhcp enabled and it is. The display says no IP. I bought the phone but do not have any documentation other than the Wiki, but I am still at a loss. What could be p...

On Tue, 2003-12-23 at 19:22, Brian West wrote: > I'm just double checking.. I was told it wasn't possible but i'm going to > ask just in case. > > Can you set outbound callerid on a channelized T1? > >I think there is a way to do something like DID with the 4 digits of >DTMF passed before the call. It is unlikely though that you will find >someone interested

...erisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] IP PHONE iareaphone x100, tested?? Good day, im gonna buy 2 IP phones to test Asterisk, i don't wanna spend too much $$$ on then, so i was looking at the internet and i read a lot, the cheapest are the Grandstream BudgetTone but some reviews of this list says they are not so good ... so i found iareaphones but i can't find reviews about them, i would like to know if someone has experience with them, at their site the phone seems to be done to work for Asterisk ... but im not gonna buy something without a good rev...

...n multicast dest of 224.0.0.1. There isn't any need to use SDP or SCCP packets to inform the phone to "listen" for those packets, they do it by default. Finally we may be able to get a solution going for Zultys handsets as they are fairly affordable with more features than some of the BudgetTones. Anyone got pointers on how to do this? Thanks Mathew -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050217/687b42ac/attachment.htm

Like most others on this list I also have some really annoying echo whenever a call goes out to the PSTN from a SIP phone... SNOM/Budgettone -> Asterisk -> X100P -> PSTN I have tried every echo canceler in the makefile and turned on and off aggressive suppressor etc. etc. etc. tried 32,16,128, and 256 bridgetaps and I can get it reduced to only a few seconds on the intro of the call and after silence, as well as a really annoy...