search for: bcm5701

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

...idge> on motherboard pci1: <PCI bus> on pcib1 pcib2: <Host to PCI bridge> on motherboard pci2: <PCI bus> on pcib2 pcib3: <Host to PCI bridge> on motherboard IOAPIC #1 intpin 12 -> irq 11 IOAPIC #1 intpin 13 -> irq 13 pci3: <PCI bus> on pcib3 bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem 0xfcf10000-0xfcf1ffff irq 11 at device 6.0 on pci3 bge0: Ethernet address: 00:06:5b:8d:20:5e miibus0: <MII bus> on bge0 brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 100...

Recent SUP. Installed on Dell PowerEdge 4600. Getting tons of: Sep 30 12:23:16 zige /kernel: bge0: gigabit link up Sep 30 12:23:46 zige last message repeated 98 times Also getting some TCP retransmits. This causes noticable delays in pretty much everything I do now. Not a problem prior to the SUP. I was on 4.8-STABLE before. When pulling/replacing cables, it went into a mode where it would

...he expire job, the NFS traffic is even higher. The news spool and INN's overview database are on an NFS mount (a NetApp filer), as well as binaries, logfiles and everything else. The NFS mounts are v3+UDP, as far as I can tell (that should be the default). The network interface is a Broadcom BCM5701 gigabit one, connected to a Cisco switch with a VLAN trunk (there are several virtual VLAN interfaces on this trunk). If it matters, we're using IPFilter for packet filtering, plus IPFW+Dummynet for traffic shaping. The load on the machine is moderate (usually below 1.0). As far as I can tel...

Hello! I have Compaq DL360G2 with Broadcom BCM5701 Gigabit Ethernet and FreeBSD 5.1R installed. There are no problems if I use bge as usual network card, but when I try to use 802.1Q vlans, I can't receive (only receive, sending is ok) packets more then 1456 bytes! What is the problem? BGE driver, VLAN driver or my network configuration? B...

...pci4 amr0: <PERC 3/DC> Firmware 1.74, BIOS 3.27, 128MB RAM pci3: <unknown card> (vendor=0x1077, dev=0x1216) at 1.0 irq 13 pcib3: <Host to PCI bridge> on motherboard IOAPIC #1 intpin 12 -> irq 17 IOAPIC #1 intpin 13 -> irq 18 pci5: <PCI bus> on pcib3 bge0: <Broadcom BCM5701 Gigabit Ethernet> mem 0xeff10000-0xeff1ffff irq 17 at device 6.0 on pci5 bge0: Ethernet address: 00:06:5b:f3:09:7d miibus0: <MII bus> on bge0 brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX,...

Hi John, And an excellent stab that was. I have two network interfaces. eth0 is a 3Com with a Broadcom Corporation NetXtreme BCM5701 Gigabit Ethernet chip, and eth1 is a 3Com 3cSOHO100-TX Hurricane chip. On the gigabit card, I couldn''t test anything, because I could not find out how to disable/enable/check checksum offloading. Using ethtool gives: Operation not supported For the Hurricane card, though, disabling check...

Hi guys, Setup is as follows: SUSE 9.3 with all patches applied samba-3.0.13-1.1 kernel-default-2.6.11.4-21.11 Network card is: Broadcom Corporation NetXtreme BCM5701 Gigabit Ethernet (rev 15) using the tg3 driver. >From time to time I see this in my log.smbd: [2006/03/23 01:03:57, 0] lib/util_sock.c:read_socket_data(384) read_socket_data: recv failure for 4. Error = Connection reset by peer When this is logged any transfers get interrupted, and I can m...

Greetings, I had a quick question about lower memory usage by memdisk. I've read through the mail archives and found a couple of posted questions but unfortunately no answers. I know the documentation states: "MEMDISK simulates a disk by claiming a chunk of high memory for the disk and a (very small - 2K typical) chunk of low (DOS) memory for the driver itself, then hooking the INT 13h

Hello, I am trying to figure out a problem I'm having using CentOS on a machine as a router. The short story is: any traffic routed through the router seems to get disconnected at random occasionally. The hardware setup is: I have two switches, the router sits between them, the webserver on the LAN switch. The machine I'm using for the router is a Dell 860 1U rackmount with two NICs,

Hi all, Currently we have severe problem and are struggling to investigate it. The problem is data broken. Reproduce pocess is following, 0. test FTP function between guest domain and FTP client(other PC). 1. put data from FTP client to guest domain. 2. get data from guest domain to FTP client. 3. compare put data and get data on FTP client. 4. repeat process from step1 to step3.