search for: bagnara

Abramo, it must be the query for llvmdev, not for cfe-dev. 2011/7/28 Abramo Bagnara <abramo.bagnara at gmail.com>: > ../llvm-r136065/configure --host=i586-mingw32msvc > --enable-targets=host-only --disable-jit --enable-bindings=none > --enable-shared --disable-threads --disable-pthreads > --disable-assertions --disable-optimized I added --enable-shared for cygmi...

Il 02/08/2011 13:02, NAKAMURA Takumi ha scritto: > Abramo, it must be the query for llvmdev, not for cfe-dev. > > 2011/7/28 Abramo Bagnara <abramo.bagnara at gmail.com>: >> ../llvm-r136065/configure --host=i586-mingw32msvc >> --enable-targets=host-only --disable-jit --enable-bindings=none >> --enable-shared --disable-threads --disable-pthreads >> --disable-assertions --disable-optimized > > I added...

...mastervol> <slavehost>::<slavevol> create push-pem force 3. Stop and start geo-rep But note that while removing brick and adding a brick, you should make sure the data from the brick being removed is synced to slave. Thanks, Kotresh HR On Wed, Feb 7, 2018 at 4:21 PM, Stefano Bagnara <lists at bago.org> wrote: > Hi all, > > i had a replica 2 gluster 3.12 between S1 and S2 (1 brick per node) > geo-replicated to S5 where both S1 and S2 were visible in the > geo-replication status and S2 "active" while S1 "passive". > > I had to repl...

Hi all, i had a replica 2 gluster 3.12 between S1 and S2 (1 brick per node) geo-replicated to S5 where both S1 and S2 were visible in the geo-replication status and S2 "active" while S1 "passive". I had to replace S1 with S3, so I did an "add-brick replica 3 S3" and then "remove-brick replica 2 S1". Now I have again a replica 2 gluster between S3 and S2

...n in Graphite. One point I do not yet fully understand is how to get array access functions from the LLVM-IR. (Probably based on getElementPtr) Another question is which polyhedral library can be used inside LLVM. One option would be ISL from Sven Verdoolaege (LGPL) another the PPL from Roberto Bagnara (GPLv3). 1.3 Generate LLVM IR from polyhedral mode ----------------------------------------- For code generation the CLooG/isl library can be used. It is LGPL licensed. Sven will also work on an CLooG using the PPL, so this could also be an option. 2. Optimize on the polyhedral representation...

In map_nt_perms any of FILE_READ_DATA, FILE_READ_EA or FILE_READ_ATTRIBUTES is mapped unconditionally to Unix read permission and similarly for write permission This means that if I put a file on a samba share where I explicitly left *only* FILE_READ_ATTRIBUTES and FILE_READ_EA the file content becomes hiddenly readable also if I decided (for very good reasons) otherwise. I'd say that when a

....0.ph.ph, i32 %j.0.reg2mem.0.ph ;2-dimension so maybe you could check the non-pointer operand of the getelementptr instructrion. > Another question is which polyhedral library can be used inside LLVM. > One option would be ISL from Sven Verdoolaege (LGPL) another the PPL > from Roberto Bagnara (GPLv3). > > 1.3 Generate LLVM IR from polyhedral mode > ----------------------------------------- > > For code generation the CLooG/isl library can be used. It is LGPL > licensed. Sven will also work on an CLooG using the PPL, so this could > also be an option. > > 2....

...difficult using scalar evolution to get the access functions. I think multi dimensional arrays will get complicated. >> Another question is which polyhedral library can be used inside LLVM. >> One option would be ISL from Sven Verdoolaege (LGPL) another the PPL >> from Roberto Bagnara (GPLv3). >> >> 1.3 Generate LLVM IR from polyhedral mode >> ----------------------------------------- >> >> For code generation the CLooG/isl library can be used. It is LGPL >> licensed. Sven will also work on an CLooG using the PPL, so this could >> also b...

Hi, is it possible to use the new "halo" feature to create a replica 2 volume on 2 bricks that are located in 2 different regions (10+ ms latency) so to be able to write to both nodes from each region without the need to a synchronous confirmation of the other node? Does this page includes the most up to date /complete docs about that feature?

in my /var/log/gluster/bricks/mybrick-path.log I get thousands of those errors: ------ [2017-11-22 21:06:23.768354] E [MSGID: 138003] [index.c:624:index_link_to_base] 0-sharedvol-index: /home/sharedvol/.glusterfs/indices/xattrop/0b852dad-b332-4bfe-a38b-976729ee46a2: Not able to add to index [Troppi collegamenti] The message "E [MSGID: 138003] [index.c:624:index_link_to_base]