Displaying 7 results from an estimated 7 matches for "b400m".
Did you mean:
9400m
2010 Nov 26
1
HA8 + B400M not configured with genconf_parameters
Hi,
On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18,
I inserted a new Digium HA8 + B400M card.
My usual installation fails.
I can see it listed :
# lspci -n | grep d161
01:0b.0 0200: d161:8007 (rev 11)
# lspci -vn
01:0b.0 0200: d161:8007 (rev 11)
Subsystem: d161:8007
Flags: medium devsel, IRQ 22
I/O ports at d400 [size=256]
Memory at fe5fe800 (32-bit,...
2011 Jun 14
0
How to set a HA8 board + B400M in NT mode ? [SOLVED]
2011/6/14 Kevin P. Fleming <kpfleming at digium.com>
> On 06/14/2011 03:11 PM, Olivier wrote:
>
>> Hi,
>>
>> 1. Is there any manual entry about modprobe's options relative to a
>> given Dahdi driver (wctdm24xxp, for instance) ?
>>
>> 2. When loading a wctdm24xxp driver, is there any parameter to pass to
>> modprobe to configure a span in
2011 Jun 14
1
How to set a HA8 board + B400M in NT mode ?
Hi,
1. Is there any manual entry about modprobe's options relative to a given
Dahdi driver (wctdm24xxp, for instance) ?
2. When loading a wctdm24xxp driver, is there any parameter to pass to
modprobe to configure a span in NT/point to point mode ?
3. After running dahdi_cfg -vvvvv , I can read with dmesg :
[ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in
TE mode
2010 Jun 17
4
Asterisk + Dahdi does not work with BRI NT mode
Hi all,
As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the
ISDN phone does not work.
There is the setting and error.
***********************Enviroment**********************************
Asterisk-1.6.1.18
dahdi-linux-2.3.0.1
dahdi-tool-2.30.
libpri-1.4.11.2
CentOS-5.5
OpenVox B400P
********************************************************************
In my case , I set prot 1
2011 Jun 15
1
How to configure unused BRI ports from a HA8 board ?
Hi,
I know this may sound a bit silly but, given some asterisk issue are still
open (see http://issues.asterisk.org/jira/browse/ASTERISK-13176 for
instance), I'm wondering if there is a recommended way to configure an used
port from a Digium HA8 + B400M board.
At the moment, my console is full with messages such as :
[Jun 15 09:06:25] WARNING[2140]: chan_dahdi.c:3369 pri_find_dchan: No
D-channels available! Using Primary channel 9 as D-channel anyway!
[Jun 15 09:06:25] WARNING[2141]: chan_dahdi.c:3369 pri_find_dchan: No
D-channels available! Us...
2013 Mar 03
0
How to configure NT/ptmp with Dahdi and BRI ?
Hi,
In my lab, I'm testing BRI spans in NT/ptmp mode.
My setup is:
asterisk 11.2.1
libpri 1.4.14
dahdi 2.6.1
wctdm24xxp (HA8 hybrid with B400M)
SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk
<----> SIP phone
The single BRI line I'm testing remains down:
CLI> pri show spans
PRI span 1/0: In Alarm, Up, Active
I'm quite certain this doesn't come from cabling as this setup wor...
2010 Dec 01
1
Dahdi 2.4.0 and unplugged spans
....0 disabled
[ 33.544757] wctdm24xxp: probe of 0000:01:0b.0 failed with error -5
[ 34.157817] dahdi: Registered tone zone 2 (France)
[ 38.873158] warning: `ntpd' uses 32-bit capabilities (legacy support in
use)
[ 47.462040] dahdi: Detected time shift.
My setup is :
Asterisk box with HA8+B400M <---ISDN/BRI----> Patton SN4638 <----SIP--->
Asterisk
Patton SN4638 is configured to behave as telco node (ie NT/PtmP).
To narrow my research scope, I'm wondering if the followin sentence is true
:
"if you load a dahdi module with a modprobe command (like modprobe
wctdm24xx...