Displaying 5 results from an estimated 5 matches for "ahd0".
Did you mean:
acd0
2008 May 27
1
SCSI bus reset with Adaptec 29320ALP and Eonstor RAID
...7.0, but I
don't understand whether it is the raid or the scsi card or something
else that is causing the computer problems when accessing the raid. My
problem is that soon after recognizing the attached disk during boot,
FreeBSD appears to hang for about 10 seconds and then says
ahd0: Recovery Initiated - Card was not paused
followed by a great detail of SCSI status information. Eventually it
says
(da1:ahd0:0:0:0): SCB 255 - timed out
(da1:ahd0:0:0:0): no longer in timeout, status = 24b
ahd0: Issued Channel A Bus Reset. 1 SCBs aborted
(da1:ahd0:0:0:0): R...
2013 Nov 14
0
[ler@lerctr.org: 10-BETA3: Bad negotiation on AHD controller]
...wn> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 1.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1
pci2: <ACPI PCI bus> on pcib2
ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x2400-0x24ff,0x2000-0x20ff mem 0xdd200000-0xdd201fff irq 32 at device 2.0 on pci2
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133MHz, 512 SCBs
ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x2c00-0x2cff,0x2800-0x28ff mem 0xd...
2003 Jun 23
1
STABLE regression with AIC-7902 controller.
...metic
problem during boot that can be cured by building a kernel without eisa
support). With STABLE (as of 19 June) the system locks up hard (no
response to the keboard) during the boot.
The last messages to appear on the console screen before the hang (with
boot_verbose set) are the following:
(ahd0:A:1:0): Sending PPR bus_width 1, period 8, offset 7f, ppr_options bf
(ahd0:A:1:0): Received PPR width 1, period 8, offset 3f,options bf
Filtered to width 1, period 8, offset 3f, options bf
ahd0: target 1 using 16bit transfers
ahd0: target 1 synchronous with period = 0x8, offset = 0x3f(RDSTR...
2008 Aug 01
1
reboot sometimes freezes, adaptic scsi card possible problem
...874608s/0x0008/0) - Battery started charging
mfi0: 3798 (270874608s/0x0008/0) - Current capacity of the battery is above
threshold
>>>>>>>>>>>HERE<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
ahd0: Selection Timeout on A:10. 0 SCBs aborted
ahd1: Selection Timeout on A:0. 0 SCBs aborted
ahd0: Selection Timeout on A:11. 0 SCBs aborted
ahd1: Selection Timeout on A:1. 0 SCBs aborted
ahd0: Selection Timeout on A:0. 0 SCBs aborted
ahd1: Selection Timeout on A:10. 0 SCBs aborted
ahd0: Selection Tim...
2003 Apr 07
1
kmem_malloc crash with 4.8
...ff irq 17 at device 3.1 on pci2
em1: Speed:N/A Duplex:N/A
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
IOAPIC #1 intpin 4 -> irq 18
IOAPIC #1 intpin 5 -> irq 19
pci3: <PCI bus> on pcib3
ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x4000-0x40ff,0x4400-0x44ff mem 0xfc300000-0xfc301fff irq 18 at device 2.0 on pci3
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x4800-0x48ff,0x4c00-0x4cff mem 0xf...