search for: 400w

Syndome Era Series *upsc output* * *battery.charge: 100 battery.runtime: 1000 <-- not reported by UPS (guesstimate) battery.voltage: 13.60 battery.voltage.high: 13.00 battery.voltage.low: 10.40 battery.voltage.nominal: 12.0 device.type: ups driver.flag.novendor: enabled driver.name: blazer_usb driver.parameter.chargetime: 43200 driver.parameter.idleload: 30 driver.parameter.pollinterval: 5

...ed to be concerned about reliable power again so I have spent a bit of time looking at options and I don't understand why most of the UPS offerings available do not come standard with a LAN port? Why is this? Do people have suggestions about my options? I have two main machines - say 250-400W total and a few small devices inc a Billion router and some USB devices. It would be nice to have at say 5-10 minutes battery backup before sending shutdown messages to the Linux machines. Thanks, Phil. -- Philip Rhoades PO Box 896 Cowra NSW 2794 Australia E-mail: phil at pricom.com.au

...ed to be concerned about reliable power again so I have spent a bit of time looking at options and I don't understand why most of the UPS offerings available do not come standard with a LAN port? Why is this? Do people have suggestions about my options? I have two main machines - say 250-400W total and a few small devices inc a Billion router and some USB devices. It would be nice to have at say 5-10 minutes battery backup before sending shutdown messages to the Linux machines. Thanks, Phil. -- Philip Rhoades PO Box 896 Cowra NSW 2794 Australia E-mail: phil at pricom.com.au

A little off topic but.... I need to put a 24 port Gig PoE switch into a small office - no computer room / rack etc. All CAT5 terminates near the owners desk (smart huh?). I want to put a PoE switch in place, with 24 ports and Gig speed. Everyone I've researched so far is LOUD... Anyone know of a quiet one? Thanks -------------- next part -------------- An HTML attachment

Hi, I'm the original poster on the subject. Thanks for all the replies. A few more points. The generator outputs 7kw @ 220V. The total PC's supplied is about 9. I estimate power consumption to be 9 x 300w=2700w 4 halogens @ 400w each=1600w 10 Compact Flourescents @ 11w =110w Therefore total power=4410w Which leaves me with spare capacity of about 2590w (in theory). I think its the halogen lamps that is helping "smooth" out the power. Previously, when I ran the generator, I did not have the halogen lamps on,...

...reliable power again > so I have spent a bit of time looking at options and I don't understand why > most of the UPS offerings available do not come standard with a LAN port? > Why is this? > > Do people have suggestions about my options? I have two main machines - > say 250-400W total and a few small devices inc a Billion router and some > USB devices. It would be nice to have at say 5-10 minutes battery backup > before sending shutdown messages to the Linux machines. > > Thanks, > > Phil. > -- > Philip Rhoades > > PO Box 896 > Cowra NSW...

Hi there. I got myself a pair of old Intel Xeon blades, which I plan to repurpose with CentOS. The model is : HP bl20p-g3 server blade Manual http://h18004.www1.hp.com/products/quickspecs/12322_ca/12322_ca.pdf Now, the main problem with this hardware is that LVD UW SCSI HDDs are hard to find and hella expensive if you find em (and of reduced capacity). Any of you know: 1. If there's any

...t be depending on any other systems for their services. A LAN card with SNMP doesn't really enforce this hierarchy, but then again, there are probably some high-availability cases where SNMP makes more sense. > Do people have suggestions about my options? I have two main machines - say 250-400W total and a few small devices inc a Billion router and some USB devices. Be sure to factor your network infrastructure into that power estimate - you will want the network links between NUT master and slave systems to be on battery power as well, or else the master will resort to guessing the sta...

...arge: 100.0 6.455483 input.voltage (raw data): [raw: 119] 6.455494 input.voltage: 118.6 6.455500 output.voltage (raw data): [raw: 119] 6.455511 output.voltage: 118.6 6.455522 STATUS: OL For anyone wondering, I wouldn't recommend these units to anyone else. A 400W dumb/"personal" UPS from APC/CyberPower/Tripp-Lite is likely just as capable, and certainly built better...

...have spent a bit of time >> looking at options and I don't understand why most of the UPS >> offerings available do not come standard with a LAN port? Why is >> this? >> >> Do people have suggestions about my options? I have two main >> machines - say 250-400W total and a few small devices inc a Billion >> router and some USB devices. It would be nice to have at say 5-10 >> minutes battery backup before sending shutdown messages to the Linux >> machines. >> >> Thanks, >> >> Phil. >> -- >> Philip Rh...

...x OUTLETS which I believe is good value. I would believe the the EATON ?5E 1500VA/900W UPS With 3 x OUTLETS would work just as well. The 1500VA also uses the same batteries as the 2000VA so I would believe it would run its raited load longer than 2000VA. My eight drive RAID driver uses less that 400W so I would expect that the device would easily run two small servers, and one monitor and/or ADSL modem for about 30 minutes, plenty of time to allow? a 5 minute wait time before a shutdown process. I like to wait 5 minutes to give people an opportunity to restore power if the issue was a tripped...

...annel Optimised Pair 2 x Western Digital WD1200JD/PD-SATA 120GB Serial ATA 150Mbps 7200rpm HDD 8Mb Cache 1 x Leadtek PX6200 TC TDH GeForce 6200 64MB PCI-E 1 x LG GDR-8163B DVD-ROM Internal: 16x Black 1 x Alps FDD B Floppy Disk Drive: 1.44Mb 3.5" Black 1 x Antec 1040B ATX Full Tower Case: 400W PSU Black 1 x Generic Adapter: Power ATX 20 pin -> 24 pin With a Digium Wildcard TDM400P TMD04B (4 Port FXO Modules) connecting to our analogue system. On calls that use the TMD400P we're getting echo on the IP phone - on inbound calls only. That is if a call is initiated from an IP ph...

I talked to Tripp Lite Technical support. Their policy is that they only support Fedora and SUSE. There is no one there that could help with Ubuntu or NUT issues. The only answer they could give me was to port the rpm files to Ubuntu and use them. This is way beyond my experience level. I will go to the local electronics store and buy a cheap USB 2 hub to see if that works. I will post the

...x OUTLETS which I believe is good value. I would believe the the EATON 5E 1500VA/900W UPS With 3 x OUTLETS would work just as well. The 1500VA also uses the same batteries as the 2000VA so I would believe it would run its raited load longer than 2000VA. My eight drive RAID driver uses less that 400W so I would expect that the device would easily run two small servers, and one monitor and/or ADSL modem for about 30 minutes, plenty of time to allow a 5 minute wait time before a shutdown process. I like to wait 5 minutes to give people an opportunity to restore power if the issue was a tripped...

Hi, Can anyone shed some light on this: My PC's are on a separate power circuit. Each PC has its own UPS. I have an old Honda generator. When the power goes out, I fire up the generator. However, the UPS's still run on battery. If I connect the PC directly to the socket and bypass the UPS, the PC works. I was told by a UPS supplier, that the power output from the generator was

Hi, I have just started to setup and configure my asterisk box and am having trouble with it. I have a dlink nic in the box as well as the digium card. When the nic is in there by itself it works, but when I put the tdm400p in, there seems to be some sort of conflict with the network card. The tdm appears as another type of network card, which I don't think it should, should it? It shows

...132 controller, and the 7th disk on a $65 4-port PCI-X SiI3124 controller that I scavenged from another server (it''s in a PCI slot, what a waste for a PCI-X card...). The rest is also dirty cheap: $65 Asus M2A-VM motherboard, $60 dual-core Athlon 64 X2 4000+, with 1GB of DDR2 800, and a 400W PSU. When testing the read throughput of individual disks with dd (roughly 81 to 97 MB/s at the beginning of the platter -- I don''t know why it varies so much between different units of the same model, additional seeks caused by reallocated sectors perhaps) I found out that an importan...

Dear Sirs. It seems to me a never ending story. We run a box with a TYAN Thunder 2500 Dual SMP mainboard, 2GB ECC Tyan certified memory, AMI Enterprise 1600 RAID adapter and additional Intel 1000/Pro server type (64 bit) GBit LAN NIC. With FreeBSD 4.8 this was stable, but to achive this state was really hard! It is a story similar to that what happend when we changed towards FreeBSD