search for: 100baset

...t a pair of identical CentOS 6.7 servers, with SuperMicro X8DTE-F motherboards, these have 2 each Intel 82574L ethernet ports. The eth0 ports are plugged in with 10' runs of brand new cat 5e cable to a Cisco Nexxus 9000 switch (provided by the data center). These servers keep coming up at 100baseT rather than gigE. I've swapped ports and cables with a different server, that server gets gigE but these supermicro's are stuck at 100baseT regardless of the port or cableused. 'ethtool eth0' says its gigE, but 'mii-tool -v eth0' says its 100baseT and doesn't even...

...d when I ` mii-tool bond0` I get 10Mbps for the bond? ----------------------------------------------------------------------------------------- ethtool em1 Settings for em1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause fram...

in dom0, how does one get and set the link information for a NIC? In a non-xen kernel, we could get this info by simply running: # ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHY...

...roller (rev 02) It is detected, but why the speed is always 100Mbps, already change cable but still no luck. I use ethtool and from the output it seems that system know that this NIC support gigabit speed : ??????? Supported link modes:?? 10baseT/Half 10baseT/Full ??????????????????????????????? 100baseT/Half 100baseT/Full ??????????????????????????????? 1000baseT/Full ??????? Supports auto-negotiation: Yes ??????? Advertised link modes:? 10baseT/Half 10baseT/Full ??????????????????????????????? 100baseT/Half 100baseT/Full ??????????????????????????????? 1000baseT/Full have change the driver r8169...

My system is: Intel CC820 motherboard (which supports PME# wake up for wake on LAN) 3com 3C905C which also supports wake on LAN via PME# Linux 5.5 The motherboard BIOS is later than one that reports an issue with WOL and this particular network card was fixed. But when I turn off the PC (shutdown or poweroff commands or front panel button), it cannot be restarted via WOL. The network light on

...ntOS 6.7 servers, with SuperMicro > X8DTE-F motherboards, these have 2 each Intel 82574L ethernet ports. > The eth0 ports are plugged in with 10' runs of brand new cat 5e cable > to a Cisco Nexxus 9000 switch (provided by the data center). > > These servers keep coming up at 100baseT rather than gigE. I've > swapped ports and cables with a different server, that server gets > gigE but these supermicro's are stuck at 100baseT regardless of the > port or cableused. > > 'ethtool eth0' says its gigE, but 'mii-tool -v eth0' says its > 1...

...n dom0 and domUs. But in virtualized environment it gives strange output why is that so? how to check it otherwise? Non-virtualized FC11 [root@fasiha home]# ethtool eth0 Settings for eth0:     Supported ports: [ TP ]     Supported link modes:   10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full                             1000baseT/Half 1000baseT/Full     Supports auto-negotiation: Yes     Advertised link modes:  10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full                             1000baseT/Half 1000baseT/Full     Advertised...

...n dom0 and domUs. But in virtualized environment it gives strange output why is that so? how to check it otherwise? Non-virtualized FC11 [root@fasiha home]# ethtool eth0 Settings for eth0:     Supported ports: [ TP ]     Supported link modes:   10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full                             1000baseT/Half 1000baseT/Full     Supports auto-negotiation: Yes     Advertised link modes:  10baseT/Half 10baseT/Full                             100baseT/Half 100baseT/Full                             1000baseT/Half 1000baseT/Full     Advertised...

...lls, or if I am dealing with a mismatch between the ethtool and the xen kernel. Any ideas? It should look like this: [root@fermigrid4 var]# ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto...

We have an HP DL360 server with dual on-board Tigon3 ethernet cards. We are using eth0, eth1 is unused at the moment. Sometimes when the network interface is under heavy load, for example moving large file transfers over rsync or NFS, the network interface stops working and we lose all connection to the server. The only solution at this point is to jump on the console and restart the network

...html read only = no ##public = yes writable = yes group = samba create mask = 0664 directory mask = 0775 ##guest ok = yes ethtool info: Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negot...

On 10/10/2016 09:31 PM, John R Pierce wrote: > > oh. Yeah, the entire "net-tools" package is deprecated. I tend to forget which of the two (ethtool or mii-tool) is in that set. # Avoid using any of these: $ rpm -ql net-tools

Hello, Just did a fresh install of xen-4.0 and using the 2.6.31.13 dom0 kernel. I have 6 linux debian guests running, and on my host console i am getting these errors rolling pretty constantly. "Attempting to checksum a non-TCP/UDP packet, dropping a protocol 1 packet" I tried doing the ethtool -K eth0 tx off and same thing on peth0, using bridged mode for network config. Any tips?

Hello, Just did a fresh install of xen-4.0 and using the 2.6.31.13 dom0 kernel. I have 6 linux debian guests running, and on my host console i am getting these errors rolling pretty constantly. "Attempting to checksum a non-TCP/UDP packet, dropping a protocol 1 packet" I tried doing the ethtool -K eth0 tx off and same thing on peth0, using bridged mode for network config. Any tips?

Hi there, I'm having an odd problem where this NIC (cheap-o, yes I know) doesn't seem to work on FreeBSD correctly. I have the same cards (even revision models) in two win boxen and they work fine. 10baseT works but not 100baseT. With a normal NIC config, without explicitly setting the media to 10baseT, it will autosense as 100BaseT @ full-duplex, showing active. However I can't ping any IP. My switch indicates that the port is not active either. If a 10baseT config, the switch will recognise that it's running...

...isc pfifo_fast 0: root refcnt 2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 The output of ethtool also looks good: root at communiceer:~# ethtool eth1 Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause fram...

Hi folks on debian stable I've a default samba file sharing config. Everything works perfectly (almost...) - samba version 3.6.6 >From linux and windows clients (wired and wifi too) when I (i.e. listen musics) often (one time every 4/5 minutes) networks suddenly collapse (for less one second) and immediately goes up. So I've an interrupt of broadcast (this happens also if I use rsync

...CentOS 6.7 servers, with SuperMicro X8DTE-F > motherboards, these have 2 each Intel 82574L ethernet ports. The eth0 > ports are plugged in with 10' runs of brand new cat 5e cable to a Cisco > Nexxus 9000 switch (provided by the data center). > > These servers keep coming up at 100baseT rather than gigE. I've swapped > ports and cables with a different server, that server gets gigE but these > supermicro's are stuck at 100baseT regardless of the port or cableused. > > 'ethtool eth0' says its gigE, but 'mii-tool -v eth0' says its 100baseT > a...

...0.0.0.0 UG 100 0 0 eth0 mpower@dodtsair:~$ sudo ethtool eth0 Settings for eth0: Link detected: yes mpower@dodtsair:~$ sudo ethtool peth0 Settings for peth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 1...

anyone know how to force network cards talk at gig speeds when all it wants to do is establish a connection at 100mbits root at host1 [/backup/cpbackup/daily]# mii-tool eth0: negotiated 100baseTx-FD, link ok eth1: negotiated 100baseTx-FD flow-control, link ok 01:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11) Subsystem: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express Flags: bus master, fast devsel,...