search for: 05e1

...rev D2 cards were full duplex). I found Donald's new stuff, and I got this output from mii-diag: [root@shiva test]# ./mii-diag -v eth0 mii-diag.c:v2.00 4/19/2000 Donald Becker (becker@scyld.com) http://www.scyld.com/diag/index.html MII PHY #24 transceiver registers: 3000 780d 0040 6176 05e1 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 1000 0300 0000 0000 0000 03ed 0300 0000 0036 000c 0f00 ff40 0026 0000 0000 000b. Basic mode control register 0x3000: Auto-negotiation enabled. You have link beat, and everything is working OK. This transceiver is capable of 100ba...

Hello, I have a problem with the latency of the packets passing a Linux router, and I thought perhaps you could put some light on it. It''s quite simple. I have one ADSL connection, and a LAN. The gateway is the Linux machine or a Windows XP machine. When the wXP is routing, for a host inside the LAN, the latency of, for example, the Counter Strike game to a given server is around 20 to 30

...ms > Hi all, > > I have a linux router using vlan patch at layer3. > All nics into the box are 3Com except 1 one them which is based on realtek > chipset. > The status are.... > > [root@fw-inet1 proc]# mii-diag eth0 > Basic registers of MII PHY #24: 3000 782d 0040 6176 05e1 0021 0000 0000. > Basic mode control register 0x3000: Auto-negotiation enabled. > You have link beat, and everything is working OK. > Your link partner is generating 10baseT link beat (no autonegotiation). > [root@fw-inet1 proc]# mii-diag eth1 > Basic registers of MII PHY #24:...

...79, IRQ 17. udev: renamed network interface eth0 to rename2 udev: renamed network interface eth1 to eth3 udev: renamed network interface rename2 to eth1 eth0: VIA Rhine II at 0xf6042000, 00:16:17:17:22:8e, IRQ 23. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth0: no IPv6 routers present So, according to the musical playing going on there, the result is: eth0: VIA Rhine eth1: IntelPro 100 (originally comes up as eth0 but gets renamed eth1) eth3: SMC1255TX (origi...

Hi Yum has just updated 5 of my Linux boxes running CentOS 4.3 to the 2.6.9-42 kernel. All is well on four of the boxes, but on the fifth the network card (eth0) will not work. I've downgraded the kernel to the previous version and the network card works fine again. I've tried removing and re-installing the new kernel, but the network card won't work with it. The details of the

Today I updated several servers running CentOS 4.3, and got the new 2.6.9-42 kernel. One of the machines serves as our firewall. After rebooting I lost all forwarding thru the machine. I reverted back to the 2.6.9-34 kernel and connectivity returned. During the few minutes that the new kernel was running I checked that the routing table looked OK, and with tcpdump I saw that indeed no traffic

Hi all, I've recently upgraded a system from CentOS 4.4 to CentOS5, and now when the system boots, the r8169 ethernet card doesn't come up. After the boot sequence, if I type "ifup eth1 | ifup eth1.10 | ifup eth1.203" then the adapter starts up ok. It seems to be something with the boot sequence it loads the ethernet adapters a different way around (ie 4.4 eth0 is now

....30i 06.28.2004 tsbogend@alpha.franken.de e100: Intel(R) PRO/100 Network Driver, 3.3.6-k2-NAPI e100: Copyright(c) 1999-2004 Intel Corporation Linux Tulip driver version 1.1.13 (May 11, 2002) PCI: Obtained IRQ 17 for device 0000:00:0d.0 tulip0: MII transceiver #1 config 1000 status 786d advertising 05e1. eth0: ADMtek Comet rev 17 at 0001e400, 00:04:5A:8C:67:6A, IRQ 17. Xen virtual console successfully installed as ttyS Event-channel device installed. Initialising Xen netif backend Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override...

...n by Donald Becker Apr 11 22:09:11 HomeC kernel: via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Apr 11 22:09:11 HomeC kernel: eth0: VIA Rhine II at 0x1c000, 00:19:66:31:9a:97, IRQ 23. Apr 11 22:09:11 HomeC kernel: eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1. Apr 11 22:09:11 HomeC kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Apr 11 22:09:11 HomeC kernel: sr 2:0:0:0: Attached scsi generic sg1 type 5 Apr 11 22:09:11 HomeC kernel: [drm] nouveau 0000:02:00.0: allocated 1440x900 fb: 0x49000, bo ffff88007877ac00 Apr 11 22:09:11 HomeC kernel...

...------------------------------ Message: 41 Date: Fri, 10 Dec 2010 16:21:29 -0000 From: "Eleni Rapsomaniki" <er339 at medschl.cam.ac.uk> To: <r-help at r-project.org> Subject: [R] survreg vs. aftreg (eha) - the relationship between fitted coefficients? Message-ID: <807B01905E122642ACFED8271250B0C306129AF8 at me-mail1.medlan.cam.ac.uk> Content-Type: text/plain; charset="iso-8859-1" Dear R-users, I need to use the aftreg function in package 'eha' to estimate failure times for left truncated survival data. Apparently, survreg still cannot fit such mod...