Ovirt devel - Apr 2009 - [Fwd: host not shown in default hardware pool]

Hello,

in addition to my trouble report from this morning, I further noticed in
the logs the following:

HOST:
-----
Apr 17 14:15:25 physical libvirt-qpid: GSSAPI Error: Unspecified GSS
failure.  Minor code may provide more information (No credentials cache
found)

ovirt-appliance:
----------------
Apr 17 14:15:25 management qpidd[2162]: 2009-apr-17 14:15:25 warning
Client closed connection with 501: internal-error: Sasl error: SASL(-1):
generic failure: GSSAPI Error: Unspecified GSS failure.  Minor code may
provide more information (No credentials cache found)
(qpid/client/SaslFactory.cpp:226)

It seems like the authentication fails and therefore the appliances
doesn't 'see' the host.

Does anybody know whether this is a libvirt-qpid problem or a qpidd
problem or some wrong configuration in ovirt? Is this a known issue or
did I hit something new?

I am really stuck here...

Thanks a lot and best regards,

Ingmar
-------------- next part --------------
An embedded message was scrubbed...
From: Ingmar Schraub <is at eseco.de>
Subject: host not shown in default hardware pool
Date: Fri, 17 Apr 2009 10:49:33 +0200
Size: 1266
URL:
<http://listman.redhat.com/archives/ovirt-devel/attachments/20090417/64a1a92a/attachment.eml>

Can you also grab the contents of /var/log/ovirt-server/db-omatic.log 
from the appliance?

Just to make sure, your node is the physical machine running the appliance?



Ingmar Schraub wrote:
> Hello,
>
> in addition to my trouble report from this morning, I further noticed in
> the logs the following:
>
> HOST:
> -----
> Apr 17 14:15:25 physical libvirt-qpid: GSSAPI Error: Unspecified GSS
> failure.  Minor code may provide more information (No credentials cache
> found)
>
> ovirt-appliance:
> ----------------
> Apr 17 14:15:25 management qpidd[2162]: 2009-apr-17 14:15:25 warning
> Client closed connection with 501: internal-error: Sasl error: SASL(-1):
> generic failure: GSSAPI Error: Unspecified GSS failure.  Minor code may
> provide more information (No credentials cache found)
> (qpid/client/SaslFactory.cpp:226)
>
> It seems like the authentication fails and therefore the appliances
> doesn't 'see' the host.
>
> Does anybody know whether this is a libvirt-qpid problem or a qpidd
> problem or some wrong configuration in ovirt? Is this a known issue or
> did I hit something new?
>
> I am really stuck here...
>
> Thanks a lot and best regards,
>
> Ingmar
>   
>
> ------------------------------------------------------------------------
>
> Subject:
> host not shown in default hardware pool
> From:
> Ingmar Schraub <is at eseco.de>
> Date:
> Fri, 17 Apr 2009 10:49:33 +0200
> To:
> ovirt-devel at redhat.com
>
> To:
> ovirt-devel at redhat.com
>
>
> Hello,
>
> I am new to ovirt and please bare with me if my question has been asked
> before. I googled, studied the wiki and searched the bug list. But I
> couldn't find anything similar.
>
> I've just set up a new server with F10, fully patched and installed
> ovirt using the Rawhide build instructions.
>
> All seems to work nicely, but I am stuck at one point.
>
> After 'sudo ovirt-install-node-stateful' followed by a host reboot
I
> started the appliance again. My problem is that the host is not shown at
> all in the default hardware pool. Any hints what's going wrong here?
> What could be missing that the appliance doesn't see my host?
> Networking, bridge, etc. is all ok.
>
> I had also to tweak /etc/httpd/conf.d/ovirt-server.conf because the
> ovirt-appliance httpd doesn't start with the config file provided.
There
> is already a ticket open on bugzilla. (#489819).
>
> Thanks a lot in advance.
>
> regards,
>
> Ingmar
>
>   
> ------------------------------------------------------------------------
>
> _______________________________________________
> Ovirt-devel mailing list
> Ovirt-devel at redhat.com
> https://www.redhat.com/mailman/listinfo/ovirt-devel
>