Nut upsdev - Sep 2021 - [HCL] POWERWALKER VFI3000TG supported by usbhid-ups

Hi All,
I just tested withoverride.battery.charge.low set to 99 (slave mode) and
lbignore flag ,the nut-monitor powered down the system as expected .
Yet, as the UPS got enough juice - it never shut down itself and thus there will
be no power up for the system (I think it's expected with this simulation),
and the system is configured to remain always off.
Best Regards,Strahil Nikolov
On Thu, Sep 16, 2021 at 2:20, Strahil Nikolov via Nut-upsdev

<nut-upsdev at alioth-lists.debian.net> wrote:   Hi All,

I'm reaching out to update you that the following UPS "works" with
usbhid-ups:

Manufacturer: Powerwalker
Device Name: VFI 3000 TG


dmesg:
usb 1-1.3: new full-speed USB device number 3 using ehci-pci
usb 1-1.3: New USB device found, idVendor=06da, idProduct=ffff, bcdDevice= 1.29
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=4
usb 1-1.3: Product: HID UPS
usb 1-1.3: Manufacturer: PPC
usb 1-1.3: SerialNumber: 210531-46690082 ?????
hid-generic 0003:06DA:FFFF.0001: hiddev96,hidraw0: USB HID v1.11 Device [PPC HID
UPS] on usb-0000:00:1a.0-1.3/input0

lsusb:
Bus 001 Device 003: ID 06da:ffff Phoenixtec Power Co., Ltd


# upsc POWERWALKER
Init SSL without certificate database
battery.charge: 93
battery.runtime: 6451
battery.type: PbAc
battery.voltage: 81
battery.voltage.nominal: 72
device.mfr: PPC
device.model: HID UPS
device.serial: 210531-46690082 ?????
device.type: ups
driver.name: usbhid-ups
driver.parameter.bus: 001
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.parameter.product: HID UPS
driver.parameter.productid: FFFF
driver.parameter.serial: 210531-46690082
driver.parameter.synchronous: no
driver.parameter.vendor: PPC
driver.parameter.vendorid: 06DA
driver.version: 2.7.4
driver.version.data: Phoenixtec/Liebert HID 0.3
driver.version.internal: 0.41
ups.load: 7
ups.mfr: PPC
ups.model: HID UPS
ups.productid: ffff
ups.serial: 210531-46690082 ?????
ups.status: OL CHRG
ups.vendorid: 06da

upscmd & upsrw did not return any output and upsrw is not allowed to change
variables (Unexpected response from upsd: ERR VAR-NOT-SUPPORTED)

Shutdown Sequence Testing result: N/A. Not tested ,yet.

Product
page:?https://powerwalker.com/?lang=en&page=product&item=10122043


Best Regards,
Strahil Nikolov


_______________________________________________
Nut-upsdev mailing list
Nut-upsdev at alioth-lists.debian.net
https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsdev
  
  
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://alioth-lists.debian.net/pipermail/nut-upsdev/attachments/20210916/9fab0f06/attachment.htm>

Hey All,

I just tested the ups setup and even without the battery low override
ups-monitor managed to cleanly shutdown my server.
As the server is not configured to power on when the power is restored, I
didn't check the full checklist.

Best Regards,Strahil Nikolov
 
 
  On Thu, Sep 16, 2021 at 8:08, Strahil Nikolov via Nut-upsdev<nut-upsdev at
alioth-lists.debian.net> wrote:  
_______________________________________________
Nut-upsdev mailing list
Nut-upsdev at alioth-lists.debian.net
https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsdev
  
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://alioth-lists.debian.net/pipermail/nut-upsdev/attachments/20210917/d9c8a78d/attachment.htm>