Hi All, I was using CBQ to control the bandwidth rate , while i use the qdisc cbq with u32 filter and route filter it is working fine ,but when i use fw classifier it seems that the bandwidth rate 100kbit is not picked. i have used the following commands /sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK --set-mark 1 /sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64 /sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 /sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000 /sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw classid 1:2 is that anything i have missed out ? i have tested these commands using Linux-2.4.10. Advance Thanks Vanitha
Hello John ,
Thanks for ur reply . But still it have not worked out.
i have attached the results is that iam making some mistakes in script please
guide me
Advance Thanks
vanitha
/sbin/tc -s qdisc show dev eth0
qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit
Sent 450 bytes 6 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
/sbin/tc -s filter show dev eth0
filter parent 1: protocol ip pref 1 fw
filter parent 1: protocol ip pref 1 fw handle 0x1 classid 1:2
/sbin/tc -s class show dev eth0
class cbq 1: root rate 10Mbit (bounded,isolated) prio no-transmit
Sent 3725 bytes 47 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:1 parent 1: rate 10Mbit prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:2 parent 1:1 rate 100Kbit (bounded) prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.79878e+06 undertime 0
/sbin/iptables -t mangle -L
Chain PREROUTING (policy ACCEPT)
target prot opt source destination
MARK tcp -- anywhere 172.16.1.81 MARK set 0x1
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
----- Original Message -----
From: john peng
To: vanitha ; lartc@mailman.ds9a.nl
Sent: Sunday, December 02, 2001 5:01 AM
Subject: Re: [LARTC] cbq-fw classifier
please use
tc -s qdisc show dev eth1
tc -s class show dev eth1
tc -s filter show dev eth1
to see where the packet goes ,
or how much it borrows .....
It seems your script can''t regular the classid 1:2
cheers
john
----- Original Message -----
From: vanitha
To: lartc@mailman.ds9a.nl
Sent: Thursday, November 01, 2001 5:04 PM
Subject: [LARTC] cbq-fw classifier
Hi All,
I was using CBQ to control the bandwidth rate , while i use the qdisc cbq
with u32 filter and route filter it is
working fine ,but when i use fw classifier it seems that the bandwidth rate
100kbit is not picked.
i have used the following commands
/sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK
--set-mark 1
/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt
1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate
10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000
/sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate
100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000
/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw
classid 1:2
is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.
Advance Thanks
Vanitha
hello john
When i changed my iptable script from PREROUTING to OUTPUT it worked fine.
I have another query
can i mark the outgoing packets by using the mac address (in the below case i
have used the ip address)
Advance Thanks
Vanitha
----- Original Message -----
From: john peng
To: vanitha ; lartc@mailman.ds9a.nl
Sent: Sunday, December 02, 2001 7:29 AM
Subject: Re: [LARTC] cbq-fw classifier
According to the results ,
packets are not filtered into classid 1:2
what is your testing scenario ?
(notice , PREROUTING don''t tack care of local generating packets )
john
----- Original Message -----
From: vanitha
To: john peng ; lartc@mailman.ds9a.nl
Sent: Thursday, November 01, 2001 8:43 PM
Subject: Re: [LARTC] cbq-fw classifier
Hello John ,
Thanks for ur reply . But still it have not worked out.
i have attached the results is that iam making some mistakes in script
please guide me
Advance Thanks
vanitha
/sbin/tc -s qdisc show dev eth0
qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit
Sent 450 bytes 6 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
/sbin/tc -s filter show dev eth0
filter parent 1: protocol ip pref 1 fw
filter parent 1: protocol ip pref 1 fw handle 0x1 classid 1:2
/sbin/tc -s class show dev eth0
class cbq 1: root rate 10Mbit (bounded,isolated) prio no-transmit
Sent 3725 bytes 47 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:1 parent 1: rate 10Mbit prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:2 parent 1:1 rate 100Kbit (bounded) prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.79878e+06 undertime 0
/sbin/iptables -t mangle -L
Chain PREROUTING (policy ACCEPT)
target prot opt source destination
MARK tcp -- anywhere 172.16.1.81 MARK set 0x1
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
----- Original Message -----
From: john peng
To: vanitha ; lartc@mailman.ds9a.nl
Sent: Sunday, December 02, 2001 5:01 AM
Subject: Re: [LARTC] cbq-fw classifier
please use
tc -s qdisc show dev eth1
tc -s class show dev eth1
tc -s filter show dev eth1
to see where the packet goes ,
or how much it borrows .....
It seems your script can''t regular the classid 1:2
cheers
john
----- Original Message -----
From: vanitha
To: lartc@mailman.ds9a.nl
Sent: Thursday, November 01, 2001 5:04 PM
Subject: [LARTC] cbq-fw classifier
Hi All,
I was using CBQ to control the bandwidth rate , while i use the qdisc
cbq with u32 filter and route filter it is
working fine ,but when i use fw classifier it seems that the bandwidth
rate 100kbit is not picked.
i have used the following commands
/sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK
--set-mark 1
/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8
avpkt 1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit
rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000
/sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit
rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000
/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw
classid 1:2
is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.
Advance Thanks
Vanitha
please use tc -s qdisc show dev eth1 tc -s class show dev eth1 tc -s filter show dev eth1 to see where the packet goes , or how much it borrows ..... It seems your script can''t regular the classid 1:2 cheers john ----- Original Message ----- From: vanitha To: lartc@mailman.ds9a.nl Sent: Thursday, November 01, 2001 5:04 PM Subject: [LARTC] cbq-fw classifier Hi All, I was using CBQ to control the bandwidth rate , while i use the qdisc cbq with u32 filter and route filter it is working fine ,but when i use fw classifier it seems that the bandwidth rate 100kbit is not picked. i have used the following commands /sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK --set-mark 1 /sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64 /sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 /sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000 /sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw classid 1:2 is that anything i have missed out ? i have tested these commands using Linux-2.4.10. Advance Thanks Vanitha
According to the results ,
packets are not filtered into classid 1:2
what is your testing scenario ?
(notice , PREROUTING don''t tack care of local generating packets )
john
----- Original Message -----
From: vanitha
To: john peng ; lartc@mailman.ds9a.nl
Sent: Thursday, November 01, 2001 8:43 PM
Subject: Re: [LARTC] cbq-fw classifier
Hello John ,
Thanks for ur reply . But still it have not worked out.
i have attached the results is that iam making some mistakes in script please
guide me
Advance Thanks
vanitha
/sbin/tc -s qdisc show dev eth0
qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit
Sent 450 bytes 6 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
/sbin/tc -s filter show dev eth0
filter parent 1: protocol ip pref 1 fw
filter parent 1: protocol ip pref 1 fw handle 0x1 classid 1:2
/sbin/tc -s class show dev eth0
class cbq 1: root rate 10Mbit (bounded,isolated) prio no-transmit
Sent 3725 bytes 47 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:1 parent 1: rate 10Mbit prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:2 parent 1:1 rate 100Kbit (bounded) prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.79878e+06 undertime 0
/sbin/iptables -t mangle -L
Chain PREROUTING (policy ACCEPT)
target prot opt source destination
MARK tcp -- anywhere 172.16.1.81 MARK set 0x1
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
----- Original Message -----
From: john peng
To: vanitha ; lartc@mailman.ds9a.nl
Sent: Sunday, December 02, 2001 5:01 AM
Subject: Re: [LARTC] cbq-fw classifier
please use
tc -s qdisc show dev eth1
tc -s class show dev eth1
tc -s filter show dev eth1
to see where the packet goes ,
or how much it borrows .....
It seems your script can''t regular the classid 1:2
cheers
john
----- Original Message -----
From: vanitha
To: lartc@mailman.ds9a.nl
Sent: Thursday, November 01, 2001 5:04 PM
Subject: [LARTC] cbq-fw classifier
Hi All,
I was using CBQ to control the bandwidth rate , while i use the qdisc cbq
with u32 filter and route filter it is
working fine ,but when i use fw classifier it seems that the bandwidth
rate 100kbit is not picked.
i have used the following commands
/sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK
--set-mark 1
/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8
avpkt 1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit
rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000
/sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit
rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000
/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw
classid 1:2
is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.
Advance Thanks
Vanitha