Michael Steinmann
2018-Dec-17 10:33 UTC
APU2, legacy firmware 4.0.22, FreeBSD 12.0 hangs in boot
Hi, Our developers ask for the full log you could provide. Thanks. Best regards, Michael Steinmann Am Sa., 15. Dez. 2018 um 21:00 Uhr schrieb Kurt Jaeger <pi at freebsd.org>:> Hi! > > Testing FreeBSD 12.0 on an apu2d4 with WLAN board, after upgrading to > > http://pcengines.ch/file/apu2_v4.0.22.rom.tar.gz > > the boot hangs after: > > [...] > Event timer "RTC" frequency 32768 Hz quality 0 > attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 > Timecounter "i8254" frequency 1193182 Hz quality 0 > Event timer "i8254" frequency 1193182 Hz quality 100 > hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 950 > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x818-0x81b on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > > It booted with the former version, but very slowly. > > I can provide a full boot log if required. Any ideas ? > > -- > pi at FreeBSD.org +49 171 3101372 2 years to go ! >
Kurt Jaeger
2018-Dec-17 10:38 UTC
APU2, legacy firmware 4.0.22, FreeBSD 12.0 hangs in boot
Hi!> Our developers ask for the full log you could provide.Below the boot1 with 4.0.22, that stalled. And the boot2, with 4.8.0.5, that worked. Serial Number: 1086158 -------------boot1----------- PC Engines apu2 coreboot build 20180312 BIOS version v4.0.22 4080 MB ECC DRAM SeaBIOS (version rel-1.11.0.7-0-gdc51f90) Press F10 key now for boot menu Booting from Hard Disk... //bboooott//ccoonnffiigg:: --DDhh --SS11115522000 0 CCoonnssoolleess:: iinntteerrnnaall vviiddeeoo//kkeeyybbooaarrdd sseerriiaall ppoorrtt BBIIOOSS ddrriivvee CC:: iiss ddiisskk00 ||// --\\||//-- \\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\ ||//--\\||//BBIIOOSS 663399kkBB//33666688779922kkBB aavvaaiillaabbllee mmeemmoorryy FFrreeeeBBSSDD//xx8866 bboooottssttrraapp llooaaddeerr,, RReevviissiioonn 11..11 --\\||//-- \\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//-- \\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\ ||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\ ||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||// --\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||// --\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //LLooaaddiinngg //bboooott//ddeeffaauullttss//llooaaddeerr..ccoonnff LLooaaddiinngg //bboooott//ddeevviiccee..hhiinnttss --\\||//--\\||//--\\ LLooaaddiinngg //bboooott//llooaaddeerr..ccoonnff ||//--\\||//--\\||//Loading /boot/loader.conf.local ``` ` s` `.....---.......--.``` -/ +o .--` /y:` +. yo`:. :o `+- y/ -/` -o/ .- ::/sy+:. / `-- / `: :` `: :` / / .- -. -- -. `:` `:` .-- `--. .---.....----. ______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ ??????????????????????????????????????????????????????????????????????????????????????????????????????????????Welcome to FreeBSD1. Boot Multi user [Enter]2. Boot Single user3. Escape to loader prompt4. RebootOptions:5. Kernel: default/2kernel (1 of 1)6. Boot OptionsAutoboot in 10 seconds, hit [Enter] to boot or any other key to stop Autoboot in 9 seconds, hit [Enter] to boot or any other key to stop Autoboot in 8 seconds, hit [Enter] to boot or any other key to stop Autoboot in 7 seconds, hit [Enter] to boot or any other key to stop Autoboot in 6 seconds, hit [Enter] to boot or any other key to stop Autoboot in 5 seconds, hit [Enter] to boot or any other key to stop Autoboot in 4 seconds, hit [Enter] to boot or any other key to stop Autoboot in 3 seconds, hit [Enter] to boot or any other key to stop Autoboot in 2 seconds, hit [Enter] to boot or any other key to stop Autoboot in 1 seconds, hit [Enter] to boot or any other key to stop Autoboot in 0 seconds, hit [Enter] to boot or any other key to stop Loading kernel... /boot/kernel/kernel text=0x1678a68 data=0x1cd288+0x768b40 syms=[0x8+0x174cd8+0x8+0x19224a] Loading configured modules... /boot/entropy size=0x1000 /boot/kernel/zfs.ko size 0x3a9a10 at 0x263e000 loading required module 'opensolaris' /boot/kernel/opensolaris.ko size 0xa4f0 at 0x29e8000 ---<<BOOT>>--- Copyright (c) 1992-2018 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 12.0-RELEASE r341666 GENERIC amd64 FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on LLVM 6.0.1) VT(vga): resolution 640x480 CPU: AMD GX-412TC SOC (998.15-MHz K8-class CPU) Origin="AuthenticAMD" Id=0x730f01 Family=0x16 Model=0x30 Stepping=1 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x3ed8220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> AMD Features2=0x1d4037ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,Topology,PNXC,DBE,PTSC,PL2I> Structured Extended Features=0x8<BMI1> XSAVE Features=0x1<XSAVEOPT> SVM: NP,NRIP,AFlush,DAssist,NAsids=8 TSC: P-state invariant, performance statistics real memory = 4815060992 (4592 MB) avail memory = 4092137472 (3902 MB) Event timer "LAPIC" quality 600 ACPI APIC Table: <CORE COREBOOT> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs FreeBSD/SMP: 1 package(s) x 4 core(s) random: unblocking device. ioapic1: Changing APIC ID to 5 ioapic0 <Version 2.1> irqs 0-23 on motherboard ioapic1 <Version 2.1> irqs 24-55 on motherboard Launching APs: 3 2 1 Timecounter "TSC" frequency 998150199 Hz quality 1000 random: entropy device external interface kbd0 at kbdmux0 netmap: loaded module [ath_hal] loaded module_register_init: MOD_LOAD (vesa, 0xffffffff810f9770, 0) error 19 nexus0 vtvga0: <VT VGA driver> on motherboard cryptosoft0: <software crypto> on motherboard acpi0: <CORE COREBOOT> on motherboard acpi0: Power Button (fixed) cpu0: <ACPI CPU> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 atrtc0: registered as a time-of-day clock, resolution 1.000000s Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x818-0x81b on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 ---------------boot2------------- PC Engines apu2 coreboot build 20180410 BIOS version v4.8.0.5 4080 MB ECC DRAM SeaBIOS (version rel-1.11.0.5-0-gd34c797) Press F10 key now for boot menu Booting from Hard Disk... /boot/config: -h -S115200 Consoles: serial port BIOS drive C: is disk0 BIOS 639kB/3405412kB available memory FreeBSD/x86 bootstrap loader, Revision 1.1 Loading /boot/defaults/loader.conf Loading /boot/device.hints Loading /boot/loader.conf Loading /boot/loader.conf.local ``` ` s` `.....---.......--.``` -/ +o .--` /y:` +. yo`:. :o `+- y/ -/` -o/ .- ::/sy+:. / `-- / `: :` `: :` / / .- -. -- -. `:` `:` .-- `--. .---.....----. ______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ ??????????????????????????????????????????????????????????????????????????????????????????????????????????????Welcome to FreeBSD1. Boot Multi user [Enter]2. Boot Single user3. Escape to loader prompt4. RebootOptions:5. Kernel: default/2kernel (1 of 1)6. Boot OptionsAutoboot in 10 seconds, hit [Enter] to boot or any other key to stop Autoboot in 9 seconds, hit [Enter] to boot or any other key to stop Autoboot in 8 seconds, hit [Enter] to boot or any other key to stop Autoboot in 7 seconds, hit [Enter] to boot or any other key to stop Autoboot in 6 seconds, hit [Enter] to boot or any other key to stop Autoboot in 5 seconds, hit [Enter] to boot or any other key to stop Autoboot in 4 seconds, hit [Enter] to boot or any other key to stop Autoboot in 3 seconds, hit [Enter] to boot or any other key to stop Autoboot in 2 seconds, hit [Enter] to boot or any other key to stop Autoboot in 1 seconds, hit [Enter] to boot or any other key to stop Autoboot in 0 seconds, hit [Enter] to boot or any other key to stop Loading kernel... /boot/kernel/kernel text=0x1678a68 data=0x1cd288+0x768b40 syms=[0x8+0x174cd8+0x8+0x19224a] Loading configured modules... /boot/kernel/zfs.ko size 0x3a9a10 at 0x263d000 loading required module 'opensolaris' /boot/kernel/opensolaris.ko size 0xa4f0 at 0x29e7000 /boot/entropy size=0x1000 ---<<BOOT>>--- Copyright (c) 1992-2018 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 12.0-RELEASE r341666 GENERIC amd64 FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on LLVM 6.0.1) VT(vga): resolution 640x480 CPU: AMD GX-412TC SOC (998.16-MHz K8-class CPU) Origin="AuthenticAMD" Id=0x730f01 Family=0x16 Model=0x30 Stepping=1 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x3ed8220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> AMD Features2=0x1d4037ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,Topology,PNXC,DBE,PTSC,PL2I> Structured Extended Features=0x8<BMI1> XSAVE Features=0x1<XSAVEOPT> SVM: NP,NRIP,AFlush,DAssist,NAsids=8 TSC: P-state invariant, performance statistics real memory = 5083496448 (4848 MB) avail memory = 4084031488 (3894 MB) Event timer "LAPIC" quality 600 ACPI APIC Table: <CORE COREBOOT> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs FreeBSD/SMP: 1 package(s) x 4 core(s) random: unblocking device. ioapic1: Changing APIC ID to 5 ioapic0 <Version 2.1> irqs 0-23 on motherboard ioapic1 <Version 2.1> irqs 24-55 on motherboard Launching APs: 2 1 3 Timecounter "TSC" frequency 998157729 Hz quality 1000 random: entropy device external interface kbd0 at kbdmux0 netmap: loaded module [ath_hal] loaded module_register_init: MOD_LOAD (vesa, 0xffffffff810f9770, 0) error 19 nexus0 vtvga0: <VT VGA driver> on motherboard cryptosoft0: <software crypto> on motherboard acpi0: <CORE COREBOOT> on motherboard acpi0: Power Button (fixed) cpu0: <ACPI CPU> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 atrtc0: registered as a time-of-day clock, resolution 1.000000s Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x818-0x81b on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: <base peripheral, IOMMU> at device 0.2 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 25 at device 2.2 on pci0 pcib1: failed to allocate initial I/O port window: 0x1000-0x1fff pci1: <ACPI PCI bus> on pcib1 igb0: <Intel(R) PRO/1000 PCI-Express Network Driver> mem 0xf7900000-0xf791ffff,0xf7920000-0xf7923fff irq 28 at device 0.0 on pci1 igb0: attach_pre capping queues at 4 igb0: using 1024 tx descriptors and 1024 rx descriptors igb0: msix_init qsets capped at 4 igb0: pxm cpus: 4 queue msgs: 4 admincnt: 1 igb0: using 4 rx queues 4 tx queues igb0: Using MSIX interrupts with 5 vectors igb0: allocated for 4 tx_queues igb0: allocated for 4 rx_queues igb0: Ethernet address: 00:0d:b9:42:4c:38 igb0: netmap queues/slots: TX 4/1024, RX 4/1024 pcib2: <ACPI PCI-PCI bridge> irq 26 at device 2.3 on pci0 pci2: <ACPI PCI bus> on pcib2 igb1: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0x2000-0x201f mem 0xf7a00000-0xf7a1ffff,0xf7a20000-0xf7a23fff irq 32 at device 0.0 on pci2 igb1: attach_pre capping queues at 4 igb1: using 1024 tx descriptors and 1024 rx descriptors igb1: msix_init qsets capped at 4 igb1: pxm cpus: 4 queue msgs: 4 admincnt: 1 igb1: using 4 rx queues 4 tx queues igb1: Using MSIX interrupts with 5 vectors igb1: allocated for 4 tx_queues igb1: allocated for 4 rx_queues igb1: Ethernet address: 00:0d:b9:42:4c:39 igb1: netmap queues/slots: TX 4/1024, RX 4/1024 pcib3: <ACPI PCI-PCI bridge> at device 2.4 on pci0 pci3: <ACPI PCI bus> on pcib3 igb2: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0x3000-0x301f mem 0xf7b00000-0xf7b1ffff,0xf7b20000-0xf7b23fff at device 0.0 on pci3 igb2: attach_pre capping queues at 4 igb2: using 1024 tx descriptors and 1024 rx descriptors igb2: msix_init qsets capped at 4 igb2: pxm cpus: 4 queue msgs: 4 admincnt: 1 igb2: using 4 rx queues 4 tx queues igb2: Using MSIX interrupts with 5 vectors igb2: allocated for 4 tx_queues igb2: allocated for 4 rx_queues igb2: Ethernet address: 00:0d:b9:42:4c:3a igb2: netmap queues/slots: TX 4/1024, RX 4/1024 pcib4: <ACPI PCI-PCI bridge> at device 2.5 on pci0 pci4: <ACPI PCI bus> on pcib4 ath0: <Atheros 9280> mem 0xf7c00000-0xf7c0ffff at device 0.0 on pci4 [ath] enabling AN_TOP2_FIXUP ath0: [HT] enabling HT modes ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 stream STBC transmit enabled ath0: [HT] 2 RX streams; 2 TX streams ath0: AR9280 mac 128.2 RF5133 phy 13.0 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 pci0: <encrypt/decrypt> at device 8.0 (no driver attached) xhci0: <AMD FCH USB 3.0 controller> mem 0xf7fa2000-0xf7fa3fff irq 18 at device 16.0 on pci0 xhci0: 32 bytes context size, 64-bit DMA xhci0: Unable to map MSI-X table usbus0 on xhci0 usbus0: 5.0Gbps Super Speed USB v3.0 ahci0: <AMD Hudson-2 AHCI SATA controller> port 0x4010-0x4017,0x4020-0x4023,0x4018-0x401f,0x4024-0x4027,0x4000-0x400f mem 0xf7fa5000-0xf7fa53ff at device 17.0 on pci0 ahci0: AHCI v1.30 with 2 6Gbps ports, Port Multiplier supported with FBS ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ehci0: <AMD FCH USB 2.0 controller> mem 0xf7fa6000-0xf7fa60ff irq 18 at device 19.0 on pci0 usbus1: EHCI version 1.0 usbus1 on ehci0 usbus1: 480Mbps High Speed USB v2.0 isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 sdhci_pci0: <Generic SD HCI> mem 0xf7fa7000-0xf7fa70ff at device 20.7 on pci0 sdhci_pci0: 1 slot(s) allocated orm0: <ISA Option ROM> at iomem 0xee800-0xeffff pnpid ORM0000 on isa0 uart0: <16550 or compatible> at port 0x3f8 irq 4 flags 0x10 on isa0 uart0: console (115200,n,8,1) uart0: non-PNP ISA device will be removed from GENERIC in FreeBSD 12. uart1: <16550 or compatible> at port 0x2f8 irq 3 on isa0 uart1: non-PNP ISA device will be removed from GENERIC in FreeBSD 12. hwpstate0: <Cool`n'Quiet 2.0> on cpu0 ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present; to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf. ZFS filesystem version: 5 ZFS storage pool version: features support (5000) Timecounters tick every 1.000 msec ugen1.1: <AMD EHCI root HUB> at usbus1 ugen0.1: <0x1022 XHCI root HUB> at usbus0 uhub0: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 uhub1: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <Crucial CT480M500SSD3 MU03> ACS-2 ATA SATA 3.x device ada0: Serial Number 14110C0A1FDA ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 457862MB (937703088 512 byte sectors) ada0: quirks=0x2<NCQ_TRIM_BROKEN> Trying to mount root from zfs:zroot/ROOT/default []... Root mount waiting for: usbus1 usbus0 uhub1: 4 ports with 4 removable, self powered uhub0: 2 ports with 2 removable, self powered Root mount waiting for: usbus1 ugen1.2: <vendor 0x0438 product 0x7900> at usbus1 uhub2 on uhub0 uhub2: <vendor 0x0438 product 0x7900, class 9/0, rev 2.00/0.18, addr 2> on usbus1 uhub2: 4 ports with 4 removable, self powered Setting hostuuid: 7b24996a-00a1-11e9-bb83-000db9424c38. Setting hostid: 0x93cb9069. Starting file system checks: Mounting local filesystems:. ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/mysql /usr/local/lib/perl5/5.28/mach/CORE 32-bit compatibility ldconfig path: /usr/lib32 Setting hostname: a3.opsec.eu. Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED Feeding entropy: . lo0: link state changed to UP Starting Network: lo0 igb0 igb1 igb2. lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6> inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet 127.0.0.1 netmask 0xff000000 groups: lo nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> igb0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> ether 00:0d:b9:42:4c:38 media: Ethernet autoselect status: no carrier nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> igb1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> ether 00:0d:b9:42:4c:39 media: Ethernet autoselect status: no carrier nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> igb2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> ether 00:0d:b9:42:4c:3a inet 193.105.105.174 netmask 0xffffffc0 broadcast 193.105.105.191 media: Ethernet autoselect status: no carrier nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> Starting devd. Starting Network: igb0. igb0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> ether 00:0d:b9:42:4c:38 media: Ethernet autoselect status: no carrier nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> Starting Network: igb1. igb1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> ether 00:0d:b9:42:4c:39 media: Ethernet autoselect status: no carrier nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> igb2: link state changed to UP Autoloading module: intpm.ko intsmb0: <AMD FCH SMBus Controller> at device 20.0 on pci0 smbus0: <System Management Bus> on intsmb0 add host 127.0.0.1: gateway lo0 fib 0: route already in table add net default: gateway 193.105.105.190 add host ::1: gateway lo0 fib 0: route already in table add net fe80::: gateway ::1 add net ff02::: gateway ::1 add net ::ffff:0.0.0.0: gateway ::1 add net ::0.0.0.0: gateway ::1 ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to deny, logging disabled Flushed all rules. 00100 allow ip from any to any via lo0 00200 deny ip from any to 127.0.0.0/8 00300 deny ip from 127.0.0.0/8 to any 00400 deny ip from any to ::1 00500 deny ip from ::1 to any 00600 allow ipv6-icmp from :: to ff02::/16 00700 allow ipv6-icmp from fe80::/10 to fe80::/10 00800 allow ipv6-icmp from fe80::/10 to ff02::/16 00900 allow ipv6-icmp from any to any icmp6types 1 01000 allow ipv6-icmp from any to any icmp6types 2,135,136 65000 allow ip from any to any Firewall rules loaded. Creating and/or trimming log files. Starting syslogd. No core dumps found. Clearing /tmp (X related). Updating motd:. Mounting late filesystems:. Configuring vt: blanktime. Performing sanity check on sshd configuration. Starting sshd. Starting cron. Starting background file system checks in 60 seconds. Sat Dec 15 22:07 FreeBSD/amd64 (...) (ttyu0) login: --------------- -- pi at FreeBSD.org +49 171 3101372 2 years to go !
Hi, Has there been any progress on this? I'm asking because I'd very much like to upgrade my apu's to FreeBSD 12 as well! Kind regards, Ruben On 12/17/18 11:38 AM, Kurt Jaeger wrote:> Hi! > >> Our developers ask for the full log you could provide. > > Below the boot1 with 4.0.22, that stalled. > > And the boot2, with 4.8.0.5, that worked. > > Serial Number: 1086158 > > -------------boot1----------- > coreboot build 20180312 > BIOS version v4.0.22 > 4080 MB ECC DRAM > > SeaBIOS (version rel-1.11.0.7-0-gdc51f90) > > Press F10 key now for boot menu > > Booting from Hard Disk... > //bboooott//ccoonnffiigg:: --DDhh --SS11115522000 > > 0 > > > > CCoonnssoolleess:: iinntteerrnnaall vviiddeeoo//kkeeyybbooaarrdd sseerriiaall ppoorrtt > > BBIIOOSS ddrriivvee CC:: iiss ddiisskk00 > > ||// --\\||//-- \\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\ ||//--\\||//BBIIOOSS 663399kkBB//33666688779922kkBB aavvaaiillaabbllee mmeemmoorryy > > > > FFrreeeeBBSSDD//xx8866 bboooottssttrraapp llooaaddeerr,, RReevviissiioonn 11..11 > > --\\||//-- \\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//-- \\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\ ||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\ ||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||// --\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||// --\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\||//--\\|| //LLooaaddiinngg //bboooott//ddeeffaauullttss//llooaaddeerr..ccoonnff > > LLooaaddiinngg //bboooott//ddeevviiccee..hhiinnttss > > --\\||//--\\||//--\\ LLooaaddiinngg //bboooott//llooaaddeerr..ccoonnff > > ||//--\\||//--\\||//Loading /boot/loader.conf.local > ``` ` s` `.....---.......--.``` -/ +o .--` /y:` +. yo`:. :o `+- y/ -/` -o/ .- ::/sy+:. / `-- / `: :` `: :` / / .- -. -- -. `:` `:` .-- `--. .---.....----. ______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ ????????????????????????????????????????????????????????????????????????????????????????????????????????????Welcome to FreeBSD1. Boot Multi user [Enter]2. Boot Single user3. Escape to loader prompt4. RebootOptions:5. Kernel: default/2kernel (1 of 1)6. Boot OptionsAutoboot in 10 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 9 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 8 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 7 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 6 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 5 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 4 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 3 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 2 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 1 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 0 seconds, hit [Enter] to boot or any other key to stop > Loading kernel... > /boot/kernel/kernel text=0x1678a68 data=0x1cd288+0x768b40 syms=[0x8+0x174cd8+0x8+0x19224a] > Loading configured modules... > /boot/entropy size=0x1000 > /boot/kernel/zfs.ko size 0x3a9a10 at 0x263e000 > loading required module 'opensolaris' > /boot/kernel/opensolaris.ko size 0xa4f0 at 0x29e8000 > ---<<BOOT>>--- > Copyright (c) 1992-2018 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 12.0-RELEASE r341666 GENERIC amd64 > FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on LLVM 6.0.1) > VT(vga): resolution 640x480 > CPU: AMD GX-412TC SOC (998.15-MHz K8-class CPU) > Origin="AuthenticAMD" Id=0x730f01 Family=0x16 Model=0x30 Stepping=1 > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > Features2=0x3ed8220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C> > AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> > AMD Features2=0x1d4037ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,Topology,PNXC,DBE,PTSC,PL2I> > Structured Extended Features=0x8<BMI1> > XSAVE Features=0x1<XSAVEOPT> > SVM: NP,NRIP,AFlush,DAssist,NAsids=8 > TSC: P-state invariant, performance statistics > real memory = 4815060992 (4592 MB) > avail memory = 4092137472 (3902 MB) > Event timer "LAPIC" quality 600 > ACPI APIC Table: <CORE COREBOOT> > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > FreeBSD/SMP: 1 package(s) x 4 core(s) > random: unblocking device. > ioapic1: Changing APIC ID to 5 > ioapic0 <Version 2.1> irqs 0-23 on motherboard > ioapic1 <Version 2.1> irqs 24-55 on motherboard > Launching APs: 3 2 1 > Timecounter "TSC" frequency 998150199 Hz quality 1000 > random: entropy device external interface > kbd0 at kbdmux0 > netmap: loaded module > [ath_hal] loaded > module_register_init: MOD_LOAD (vesa, 0xffffffff810f9770, 0) error 19 > nexus0 > vtvga0: <VT VGA driver> on motherboard > cryptosoft0: <software crypto> on motherboard > acpi0: <CORE COREBOOT> on motherboard > acpi0: Power Button (fixed) > cpu0: <ACPI CPU> on acpi0 > atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 > atrtc0: registered as a time-of-day clock, resolution 1.000000s > Event timer "RTC" frequency 32768 Hz quality 0 > attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 > Timecounter "i8254" frequency 1193182 Hz quality 0 > Event timer "i8254" frequency 1193182 Hz quality 100 > hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 950 > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x818-0x81b on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > > ---------------boot2------------- > > PC Engines apu2 > coreboot build 20180410 > BIOS version v4.8.0.5 > 4080 MB ECC DRAM > > SeaBIOS (version rel-1.11.0.5-0-gd34c797) > > Press F10 key now for boot menu > > Booting from Hard Disk... > /boot/config: -h -S115200 > > Consoles: serial port > BIOS drive C: is disk0 > > > BIOS 639kB/3405412kB available memory > > FreeBSD/x86 bootstrap loader, Revision 1.1 > Loading /boot/defaults/loader.conf > Loading /boot/device.hints > Loading /boot/loader.conf > Loading /boot/loader.conf.local > ``` ` s` `.....---.......--.``` -/ +o .--` /y:` +. yo`:. :o `+- y/ -/` -o/ .- ::/sy+:. / `-- / `: :` `: :` / / .- -. -- -. `:` `:` .-- `--. .---.....----. ______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ ????????????????????????????????????????????????????????????????????????????????????????????????????????????Welcome to FreeBSD1. Boot Multi user [Enter]2. Boot Single user3. Escape to loader prompt4. RebootOptions:5. Kernel: default/2kernel (1 of 1)6. Boot OptionsAutoboot in 10 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 9 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 8 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 7 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 6 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 5 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 4 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 3 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 2 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 1 seconds, hit [Enter] to boot or any other key to stop > Autoboot in 0 seconds, hit [Enter] to boot or any other key to stop > Loading kernel... > /boot/kernel/kernel text=0x1678a68 data=0x1cd288+0x768b40 syms=[0x8+0x174cd8+0x8+0x19224a] > Loading configured modules... > /boot/kernel/zfs.ko size 0x3a9a10 at 0x263d000 > loading required module 'opensolaris' > /boot/kernel/opensolaris.ko size 0xa4f0 at 0x29e7000 > /boot/entropy size=0x1000 > ---<<BOOT>>--- > Copyright (c) 1992-2018 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 12.0-RELEASE r341666 GENERIC amd64 > FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on LLVM 6.0.1) > VT(vga): resolution 640x480 > CPU: AMD GX-412TC SOC (998.16-MHz K8-class CPU) > Origin="AuthenticAMD" Id=0x730f01 Family=0x16 Model=0x30 Stepping=1 > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > Features2=0x3ed8220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C> > AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> > AMD Features2=0x1d4037ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,Topology,PNXC,DBE,PTSC,PL2I> > Structured Extended Features=0x8<BMI1> > XSAVE Features=0x1<XSAVEOPT> > SVM: NP,NRIP,AFlush,DAssist,NAsids=8 > TSC: P-state invariant, performance statistics > real memory = 5083496448 (4848 MB) > avail memory = 4084031488 (3894 MB) > Event timer "LAPIC" quality 600 > ACPI APIC Table: <CORE COREBOOT> > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > FreeBSD/SMP: 1 package(s) x 4 core(s) > random: unblocking device. > ioapic1: Changing APIC ID to 5 > ioapic0 <Version 2.1> irqs 0-23 on motherboard > ioapic1 <Version 2.1> irqs 24-55 on motherboard > Launching APs: 2 1 3 > Timecounter "TSC" frequency 998157729 Hz quality 1000 > random: entropy device external interface > kbd0 at kbdmux0 > netmap: loaded module > [ath_hal] loaded > module_register_init: MOD_LOAD (vesa, 0xffffffff810f9770, 0) error 19 > nexus0 > vtvga0: <VT VGA driver> on motherboard > cryptosoft0: <software crypto> on motherboard > acpi0: <CORE COREBOOT> on motherboard > acpi0: Power Button (fixed) > cpu0: <ACPI CPU> on acpi0 > atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 > atrtc0: registered as a time-of-day clock, resolution 1.000000s > Event timer "RTC" frequency 32768 Hz quality 0 > attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 > Timecounter "i8254" frequency 1193182 Hz quality 0 > Event timer "i8254" frequency 1193182 Hz quality 100 > hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 950 > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x818-0x81b on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: <base peripheral, IOMMU> at device 0.2 (no driver attached) > pcib1: <ACPI PCI-PCI bridge> irq 25 at device 2.2 on pci0 > pcib1: failed to allocate initial I/O port window: 0x1000-0x1fff > pci1: <ACPI PCI bus> on pcib1 > igb0: <Intel(R) PRO/1000 PCI-Express Network Driver> mem 0xf7900000-0xf791ffff,0xf7920000-0xf7923fff irq 28 at device 0.0 on pci1 > igb0: attach_pre capping queues at 4 > igb0: using 1024 tx descriptors and 1024 rx descriptors > igb0: msix_init qsets capped at 4 > igb0: pxm cpus: 4 queue msgs: 4 admincnt: 1 > igb0: using 4 rx queues 4 tx queues > igb0: Using MSIX interrupts with 5 vectors > igb0: allocated for 4 tx_queues > igb0: allocated for 4 rx_queues > igb0: Ethernet address: 00:0d:b9:42:4c:38 > igb0: netmap queues/slots: TX 4/1024, RX 4/1024 > pcib2: <ACPI PCI-PCI bridge> irq 26 at device 2.3 on pci0 > pci2: <ACPI PCI bus> on pcib2 > igb1: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0x2000-0x201f mem 0xf7a00000-0xf7a1ffff,0xf7a20000-0xf7a23fff irq 32 at device 0.0 on pci2 > igb1: attach_pre capping queues at 4 > igb1: using 1024 tx descriptors and 1024 rx descriptors > igb1: msix_init qsets capped at 4 > igb1: pxm cpus: 4 queue msgs: 4 admincnt: 1 > igb1: using 4 rx queues 4 tx queues > igb1: Using MSIX interrupts with 5 vectors > igb1: allocated for 4 tx_queues > igb1: allocated for 4 rx_queues > igb1: Ethernet address: 00:0d:b9:42:4c:39 > igb1: netmap queues/slots: TX 4/1024, RX 4/1024 > pcib3: <ACPI PCI-PCI bridge> at device 2.4 on pci0 > pci3: <ACPI PCI bus> on pcib3 > igb2: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0x3000-0x301f mem 0xf7b00000-0xf7b1ffff,0xf7b20000-0xf7b23fff at device 0.0 on pci3 > igb2: attach_pre capping queues at 4 > igb2: using 1024 tx descriptors and 1024 rx descriptors > igb2: msix_init qsets capped at 4 > igb2: pxm cpus: 4 queue msgs: 4 admincnt: 1 > igb2: using 4 rx queues 4 tx queues > igb2: Using MSIX interrupts with 5 vectors > igb2: allocated for 4 tx_queues > igb2: allocated for 4 rx_queues > igb2: Ethernet address: 00:0d:b9:42:4c:3a > igb2: netmap queues/slots: TX 4/1024, RX 4/1024 > pcib4: <ACPI PCI-PCI bridge> at device 2.5 on pci0 > pci4: <ACPI PCI bus> on pcib4 > ath0: <Atheros 9280> mem 0xf7c00000-0xf7c0ffff at device 0.0 on pci4 > [ath] enabling AN_TOP2_FIXUP > ath0: [HT] enabling HT modes > ath0: [HT] 1 stream STBC receive enabled > ath0: [HT] 1 stream STBC transmit enabled > ath0: [HT] 2 RX streams; 2 TX streams > ath0: AR9280 mac 128.2 RF5133 phy 13.0 > ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 > pci0: <encrypt/decrypt> at device 8.0 (no driver attached) > xhci0: <AMD FCH USB 3.0 controller> mem 0xf7fa2000-0xf7fa3fff irq 18 at device 16.0 on pci0 > xhci0: 32 bytes context size, 64-bit DMA > xhci0: Unable to map MSI-X table > usbus0 on xhci0 > usbus0: 5.0Gbps Super Speed USB v3.0 > ahci0: <AMD Hudson-2 AHCI SATA controller> port 0x4010-0x4017,0x4020-0x4023,0x4018-0x401f,0x4024-0x4027,0x4000-0x400f mem 0xf7fa5000-0xf7fa53ff at device 17.0 on pci0 > ahci0: AHCI v1.30 with 2 6Gbps ports, Port Multiplier supported with FBS > ahcich0: <AHCI channel> at channel 0 on ahci0 > ahcich1: <AHCI channel> at channel 1 on ahci0 > ehci0: <AMD FCH USB 2.0 controller> mem 0xf7fa6000-0xf7fa60ff irq 18 at device 19.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci0 > usbus1: 480Mbps High Speed USB v2.0 > isab0: <PCI-ISA bridge> at device 20.3 on pci0 > isa0: <ISA bus> on isab0 > sdhci_pci0: <Generic SD HCI> mem 0xf7fa7000-0xf7fa70ff at device 20.7 on pci0 > sdhci_pci0: 1 slot(s) allocated > orm0: <ISA Option ROM> at iomem 0xee800-0xeffff pnpid ORM0000 on isa0 > uart0: <16550 or compatible> at port 0x3f8 irq 4 flags 0x10 on isa0 > uart0: console (115200,n,8,1) > uart0: non-PNP ISA device will be removed from GENERIC in FreeBSD 12. > uart1: <16550 or compatible> at port 0x2f8 irq 3 on isa0 > uart1: non-PNP ISA device will be removed from GENERIC in FreeBSD 12. > hwpstate0: <Cool`n'Quiet 2.0> on cpu0 > ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present; > to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf. > ZFS filesystem version: 5 > ZFS storage pool version: features support (5000) > Timecounters tick every 1.000 msec > ugen1.1: <AMD EHCI root HUB> at usbus1 > ugen0.1: <0x1022 XHCI root HUB> at usbus0 > uhub0: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > uhub1: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 > ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 > ada0: <Crucial CT480M500SSD3 MU03> ACS-2 ATA SATA 3.x device > ada0: Serial Number 14110C0A1FDA > ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) > ada0: Command Queueing enabled > ada0: 457862MB (937703088 512 byte sectors) > ada0: quirks=0x2<NCQ_TRIM_BROKEN> > Trying to mount root from zfs:zroot/ROOT/default []... > Root mount waiting for: usbus1 usbus0 > uhub1: 4 ports with 4 removable, self powered > uhub0: 2 ports with 2 removable, self powered > Root mount waiting for: usbus1 > ugen1.2: <vendor 0x0438 product 0x7900> at usbus1 > uhub2 on uhub0 > uhub2: <vendor 0x0438 product 0x7900, class 9/0, rev 2.00/0.18, addr 2> on usbus1 > uhub2: 4 ports with 4 removable, self powered > Setting hostuuid: 7b24996a-00a1-11e9-bb83-000db9424c38. > Setting hostid: 0x93cb9069. > Starting file system checks: > Mounting local filesystems:. > ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/mysql /usr/local/lib/perl5/5.28/mach/CORE > 32-bit compatibility ldconfig path: /usr/lib32 > Setting hostname: a3.opsec.eu. > Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED > Feeding entropy: . > lo0: link state changed to UP > Starting Network: lo0 igb0 igb1 igb2. > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6> > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 > inet 127.0.0.1 netmask 0xff000000 > groups: lo > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > igb0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> > ether 00:0d:b9:42:4c:38 > media: Ethernet autoselect > status: no carrier > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > igb1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> > ether 00:0d:b9:42:4c:39 > media: Ethernet autoselect > status: no carrier > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > igb2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> > ether 00:0d:b9:42:4c:3a > inet 193.105.105.174 netmask 0xffffffc0 broadcast 193.105.105.191 > media: Ethernet autoselect > status: no carrier > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > Starting devd. > Starting Network: igb0. > igb0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> > ether 00:0d:b9:42:4c:38 > media: Ethernet autoselect > status: no carrier > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > Starting Network: igb1. > igb1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6> > ether 00:0d:b9:42:4c:39 > media: Ethernet autoselect > status: no carrier > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > igb2: link state changed to UP > Autoloading module: intpm.ko > intsmb0: <AMD FCH SMBus Controller> at device 20.0 on pci0 > smbus0: <System Management Bus> on intsmb0 > add host 127.0.0.1: gateway lo0 fib 0: route already in table > add net default: gateway 193.105.105.190 > add host ::1: gateway lo0 fib 0: route already in table > add net fe80::: gateway ::1 > add net ff02::: gateway ::1 > add net ::ffff:0.0.0.0: gateway ::1 > add net ::0.0.0.0: gateway ::1 > ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to deny, logging disabled > Flushed all rules. > 00100 allow ip from any to any via lo0 > 00200 deny ip from any to 127.0.0.0/8 > 00300 deny ip from 127.0.0.0/8 to any > 00400 deny ip from any to ::1 > 00500 deny ip from ::1 to any > 00600 allow ipv6-icmp from :: to ff02::/16 > 00700 allow ipv6-icmp from fe80::/10 to fe80::/10 > 00800 allow ipv6-icmp from fe80::/10 to ff02::/16 > 00900 allow ipv6-icmp from any to any icmp6types 1 > 01000 allow ipv6-icmp from any to any icmp6types 2,135,136 > 65000 allow ip from any to any > Firewall rules loaded. > Creating and/or trimming log files. > Starting syslogd. > No core dumps found. > Clearing /tmp (X related). > Updating motd:. > Mounting late filesystems:. > Configuring vt: blanktime. > Performing sanity check on sshd configuration. > Starting sshd. > Starting cron. > Starting background file system checks in 60 seconds. > > Sat Dec 15 22:07 > FreeBSD/amd64 (...) (ttyu0) > > login: > --------------- > > > _______________________________________________ > freebsd-stable at freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org" >