On 10/25/2017 4:54 PM, Mike Tancsa wrote:> While testing out our nanobsd RELENG11 images, I noticed a strange > routing issue. Using a standard pppoe config that has been working fine > on RELENG8,9,10 I am getting bogus routing entries. > having the commands in ppp.linkup > > pppoe: > add 192.168.134.2/32 HISADDR > add 192.168.134.3/32 HISADDR > add 192.168.134.4/32 HISADDR > add 192.168.134.5/32 HISADDRUpping the logs with debug ppp[60212]: tun0: Command: pppoe: add 192.168.134.2/32 HISADDR ppp[60212]: tun0: Debug: wrote 124: cmd = Add, dst = 192.168.134.2, gateway = 64.7.128.7 The gateway is correct. Seems right, but its not installing it right. It also borkes on the ipv6 addr which I have disabled ppp[60212]: tun0: Warning: ff02::: Change route failed: errno: Value too large to be stored in data type ppp[60212]: tun0: Debug: deflink: DescriptorRead: read 14/2048 from 1 ppp[60212]: tun0: Debug: proto_LayerPull: unknown -> 0xc021 ppp[60212]: tun0: Debug: link_PullPacket: Despatch proto 0xc021 Any ideas ? ---Mike -- ------------------- Mike Tancsa, tel +1 519 651 3400 Sentex Communications, mike at sentex.net Providing Internet services since 1994 www.sentex.net Cambridge, Ontario Canada http://www.tancsa.com/
On 26.10.2017 04:10, Mike Tancsa wrote:> On 10/25/2017 4:54 PM, Mike Tancsa wrote: >> While testing out our nanobsd RELENG11 images, I noticed a strange >> routing issue. Using a standard pppoe config that has been working fine >> on RELENG8,9,10 I am getting bogus routing entries. >> having the commands in ppp.linkup >> >> pppoe: >> add 192.168.134.2/32 HISADDR >> add 192.168.134.3/32 HISADDR >> add 192.168.134.4/32 HISADDR >> add 192.168.134.5/32 HISADDR > > Upping the logs with debug > > > ppp[60212]: tun0: Command: pppoe: add 192.168.134.2/32 HISADDR > ppp[60212]: tun0: Debug: wrote 124: cmd = Add, dst = 192.168.134.2, > gateway = 64.7.128.7 > > The gateway is correct. Seems right, but its not installing it right. > > > > > It also borkes on the ipv6 addr which I have disabled > > ppp[60212]: tun0: Warning: ff02::: Change route failed: errno: Value too > large to be stored in data type > ppp[60212]: tun0: Debug: deflink: DescriptorRead: read 14/2048 from 1 > ppp[60212]: tun0: Debug: proto_LayerPull: unknown -> 0xc021 > ppp[60212]: tun0: Debug: link_PullPacket: Despatch proto 0xc021 > > > Any ideas ?Are you sure that: 1) your ppp(8) binary is in sync with the kernel in the Nanobsd build ? Generally that would be /usr/sbin/ppp but in your case I'd check twice if this is the case. 2) your /sbin/route and /usr/bin/netstat are in sync too? Try using "route -n monitor" in the background to see what "ppp" really sends to the kernel. Try using "mpd5" instead of "ppp" to make PPPoE connection and see if it runs into same problem.