Seems to be related to be related to your SSD drive or the SATA control. do
you a secondary SSD or HDD to try on this machine? I've seen this happen on
my Intel SSD in the past.
Thx
.
On Wed, Aug 19, 2015 at 8:07 AM, Gerhard Schmidt <estartu at ze.tum.de>
wrote:
> Hi,
>
> I'm trying to install FreeBSD 10.2 on a MacPro.
>
> Installing and Booting works. But a few seconds after login and accessing
> the Harddisk, I'm getting the following errors.
> ahcich0: Timeout on slot 13 port 0
> ahcich0: is 00000008 cs 00000000 ss 00000000 rs ffffffff tfd 40 serr
> 00000000 cmd 0000cd17
> (ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 00 28 15 40 40 2f 00 00
> 01 00 00
> (ada0:ahcich0:0:0:0): CAM status: Command timeout
> (ada0:ahcich0:0:0:0): Retrying command
> ahcich0: Timeout on slot 15 port 0
> ahcich0: is 00000008 cs 00000000 ss 00000000 rs ffffffff tfd 40 serr
> 00000000 cmd 0000cf17
> (ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 08 a0 5f bd 40 13 00 00
> 00 00 00
> (ada0:ahcich0:0:0:0): CAM status: Command timeout
> (ada0:ahcich0:0:0:0): Retrying command
> ahcich0: Timeout on slot 2 port 0
> ahcich0: is 00000008 cs 00000000 ss 00000000 rs ffffffff tfd 40 serr
> 00000000 cmd 0000c217
> (ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 08 c0 23 bd 40 13 00 00
> 00 00 00
> (ada0:ahcich0:0:0:0): CAM status: Command timeout
> (ada0:ahcich0:0:0:0): Retrying command
>
> Any Ideas what causes this and what can be done to fix it.
>
> the dmesg of the MacPro is the following
>
> Copyright (c) 1992-2015 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 10.2-RELEASE #0 r286666: Wed Aug 12 15:26:37 UTC 2015
> root at releng1.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC amd64
> FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
> VT: running with driver "efifb".
> CPU: Intel(R) Xeon(R) CPU E5-2697 v2 @ 2.70GHz (2700.06-MHz K8-class CPU)
> Origin="GenuineIntel" Id=0x306e4 Family=0x6 Model=0x3e
Stepping=4
>
>
>
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>
>
>
Features2=0x7fbee3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,DCA,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
> AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
> AMD Features2=0x1<LAHF>
> Structured Extended Features=0x281<FSGSBASE,SMEP,ERMS>
> XSAVE Features=0x1<XSAVEOPT>
> VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr
> TSC: P-state invariant, performance statistics
> real memory = 68719476736 (65536 MB)
> avail memory = 66655334400 (63567 MB)
> Event timer "LAPIC" quality 600
> ACPI APIC Table: <APPLE Apple00>
> FreeBSD/SMP: Multiprocessor System Detected: 24 CPUs
> FreeBSD/SMP: 1 package(s) x 12 core(s) x 2 SMT threads
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> cpu2 (AP): APIC ID: 2
> cpu3 (AP): APIC ID: 3
> cpu4 (AP): APIC ID: 4
> cpu5 (AP): APIC ID: 5
> cpu6 (AP): APIC ID: 6
> cpu7 (AP): APIC ID: 7
> cpu8 (AP): APIC ID: 8
> cpu9 (AP): APIC ID: 9
> cpu10 (AP): APIC ID: 10
> cpu11 (AP): APIC ID: 11
> cpu12 (AP): APIC ID: 16
> cpu13 (AP): APIC ID: 17
> cpu14 (AP): APIC ID: 18
> cpu15 (AP): APIC ID: 19
> cpu16 (AP): APIC ID: 20
> cpu17 (AP): APIC ID: 21
> cpu18 (AP): APIC ID: 22
> cpu19 (AP): APIC ID: 23
> cpu20 (AP): APIC ID: 24
> cpu21 (AP): APIC ID: 25
> cpu22 (AP): APIC ID: 26
> cpu23 (AP): APIC ID: 27
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> ioapic1 <Version 2.0> irqs 24-47 on motherboard
> lapic0: Forcing LINT1 to edge trigger
> random: <Software, Yarrow> initialized
> module_register_init: MOD_LOAD (vesa, 0xffffffff80db8eb0, 0) error 19
> kbd0 at kbdmux0
> acpi0: <APPLE Apple00> on motherboard
> acpi0: Power Button (fixed)
> unknown: I/O range not supported
> Timecounter "HPET" frequency 14318180 Hz quality 950
> Event timer "HPET" frequency 14318180 Hz quality 350
> Event timer "HPET1" frequency 14318180 Hz quality 340
> Event timer "HPET2" frequency 14318180 Hz quality 340
> Event timer "HPET3" frequency 14318180 Hz quality 340
> Event timer "HPET4" frequency 14318180 Hz quality 340
> Event timer "HPET5" frequency 14318180 Hz quality 340
> Event timer "HPET6" frequency 14318180 Hz quality 340
> Event timer "HPET7" frequency 14318180 Hz quality 340
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> cpu2: <ACPI CPU> on acpi0
> cpu3: <ACPI CPU> on acpi0
> cpu4: <ACPI CPU> on acpi0
> cpu5: <ACPI CPU> on acpi0
> cpu6: <ACPI CPU> on acpi0
> cpu7: <ACPI CPU> on acpi0
> cpu8: <ACPI CPU> on acpi0
> cpu9: <ACPI CPU> on acpi0
> cpu10: <ACPI CPU> on acpi0
> cpu11: <ACPI CPU> on acpi0
> cpu12: <ACPI CPU> on acpi0
> cpu13: <ACPI CPU> on acpi0
> cpu14: <ACPI CPU> on acpi0
> cpu15: <ACPI CPU> on acpi0
> cpu16: <ACPI CPU> on acpi0
> cpu17: <ACPI CPU> on acpi0
> cpu18: <ACPI CPU> on acpi0
> cpu19: <ACPI CPU> on acpi0
> cpu20: <ACPI CPU> on acpi0
> cpu21: <ACPI CPU> on acpi0
> cpu22: <ACPI CPU> on acpi0
> cpu23: <ACPI CPU> on acpi0
> atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
> Event timer "RTC" frequency 32768 Hz quality 0
> attimer0: <AT timer> port 0x40-0x43,0x50-0x53 on acpi0
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Event timer "i8254" frequency 1193182 Hz quality 100
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
> acpi_ec0: <Embedded Controller: GPE 0x17> port 0x62,0x66 on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pci16: <ACPI PCI bus> on pcib1
> pcib2: <ACPI PCI-PCI bridge> mem 0xbf900000-0xbf93ffff at device 0.0
on
> pci16
> pci17: <ACPI PCI bus> on pcib2
> pcib3: <ACPI PCI-PCI bridge> at device 1.0 on pci17
> pci18: <ACPI PCI bus> on pcib3
> xhci0: <XHCI (generic) USB 3.0 controller> mem
> 0xa0900000-0xa090ffff,0xa0910000-0xa0910fff,0xa0911000-0xa0911fff at
> device 0.0 on pci18
> xhci0: 32 bytes context size, 64-bit DMA
> usbus0 on xhci0
> pcib4: <ACPI PCI-PCI bridge> at device 2.0 on pci17
> pci20: <ACPI PCI bus> on pcib4
> pcib5: <ACPI PCI-PCI bridge> at device 8.0 on pci17
> pci19: <ACPI PCI bus> on pcib5
> pcib6: <ACPI PCI-PCI bridge> at device 9.0 on pci17
> pci91: <ACPI PCI bus> on pcib6
> pcib7: <ACPI PCI-PCI bridge> at device 10.0 on pci17
> pci162: <ACPI PCI bus> on pcib7
> pcib8: <ACPI PCI-PCI bridge> at device 2.0 on pci0
> pci2: <ACPI PCI bus> on pcib8
> vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem
> 0x80000000-0x8fffffff,0xa0700000-0xa073ffff at device 0.0 on pci2
> hdac0: <ATI R1000 HDA Controller> mem 0xa0760000-0xa0763fff at device
0.1
> on pci2
> hdac0: hdac_get_capabilities: Invalid corb size (0)
> device_attach: hdac0 attach returned 6
> pcib9: <ACPI PCI-PCI bridge> at device 3.0 on pci0
> pci6: <ACPI PCI bus> on pcib9
> vgapci1: <VGA-compatible display> port 0x2000-0x20ff mem
> 0x90000000-0x9fffffff,0xa0600000-0xa063ffff at device 0.0 on pci6
> hdac0: <ATI R1000 HDA Controller> mem 0xa0660000-0xa0663fff at device
0.1
> on pci6
> hdac0: hdac_get_capabilities: Invalid corb size (0)
> device_attach: hdac0 attach returned 6
> pcib10: <ACPI PCI-PCI bridge> at device 17.0 on pci0
> pci10: <ACPI PCI bus> on pcib10
> pci0: <simple comms> at device 22.0 (no driver attached)
> hdac0: <Intel Patsburg HDA Controller> mem 0xa0820000-0xa0823fff at
device
> 27.0 on pci0
> pcib11: <ACPI PCI-PCI bridge> at device 28.0 on pci0
> pci11: <ACPI PCI bus> on pcib11
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x57766000> mem
> 0xa0300000-0xa030ffff,0xa0310000-0xa031ffff at device 0.0 on pci11
> bge0: CHIP ID 0x57766000; ASIC REV 0x57766; CHIP REV 0x577660; PCI-E
> miibus0: <MII bus> on bge0
> brgphy0: <BCM57765 1000BASE-T media interface> PHY 1 on miibus0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-master, 1000baseT-FDX,
> 1000baseT-FDX-master, auto, auto-flow
> bge0: Using defaults for TSO: 65518/35/2048
> bge0: Ethernet address: 00:3e:e1:c2:1a:e3
> pcib12: <ACPI PCI-PCI bridge> at device 28.1 on pci0
> pci12: <ACPI PCI bus> on pcib12
> bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x57766000> mem
> 0xa0400000-0xa040ffff,0xa0410000-0xa041ffff at device 0.0 on pci12
> bge1: CHIP ID 0x57766000; ASIC REV 0x57766; CHIP REV 0x577660; PCI-E
> miibus1: <MII bus> on bge1
> brgphy1: <BCM57765 1000BASE-T media interface> PHY 1 on miibus1
> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-master, 1000baseT-FDX,
> 1000baseT-FDX-master, auto, auto-flow
> bge1: Using defaults for TSO: 65518/35/2048
> bge1: Ethernet address: 00:3e:e1:c2:1a:e2
> pcib13: <ACPI PCI-PCI bridge> at device 28.2 on pci0
> pci13: <ACPI PCI bus> on pcib13
> pci13: <network> at device 0.0 (no driver attached)
> pcib14: <ACPI PCI-PCI bridge> at device 28.4 on pci0
> pci14: <ACPI PCI bus> on pcib14
> ahci0: <AHCI SATA controller> mem 0xa0500000-0xa0501fff at device 0.0
on
> pci14
> ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier not supported
> ahcich0: <AHCI channel> at channel 0 on ahci0
> ehci0: <Intel Patsburg USB 2.0 controller> mem 0xa0827800-0xa0827bff
at
> device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1 on ehci0
> pcib15: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci15: <ACPI PCI bus> on pcib15
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> acpi_button0: <Power Button> on acpi0
> acpi_button1: <Sleep Button> on acpi0
> ppc0: cannot reserve I/O port range
> uart0: <8250 or 16450 or compatible> at port 0x3f8-0x3ff irq 4 flags
0x10
> on isa0
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> est1: <Enhanced SpeedStep Frequency Control> on cpu1
> est2: <Enhanced SpeedStep Frequency Control> on cpu2
> est3: <Enhanced SpeedStep Frequency Control> on cpu3
> est4: <Enhanced SpeedStep Frequency Control> on cpu4
> est5: <Enhanced SpeedStep Frequency Control> on cpu5
> est6: <Enhanced SpeedStep Frequency Control> on cpu6
> est7: <Enhanced SpeedStep Frequency Control> on cpu7
> est8: <Enhanced SpeedStep Frequency Control> on cpu8
> est9: <Enhanced SpeedStep Frequency Control> on cpu9
> est10: <Enhanced SpeedStep Frequency Control> on cpu10
> est11: <Enhanced SpeedStep Frequency Control> on cpu11
> est12: <Enhanced SpeedStep Frequency Control> on cpu12
> est13: <Enhanced SpeedStep Frequency Control> on cpu13
> est14: <Enhanced SpeedStep Frequency Control> on cpu14
> est15: <Enhanced SpeedStep Frequency Control> on cpu15
> est16: <Enhanced SpeedStep Frequency Control> on cpu16
> est17: <Enhanced SpeedStep Frequency Control> on cpu17
> est18: <Enhanced SpeedStep Frequency Control> on cpu18
> est19: <Enhanced SpeedStep Frequency Control> on cpu19
> est20: <Enhanced SpeedStep Frequency Control> on cpu20
> est21: <Enhanced SpeedStep Frequency Control> on cpu21
> est22: <Enhanced SpeedStep Frequency Control> on cpu22
> est23: <Enhanced SpeedStep Frequency Control> on cpu23
> random: unblocking device.
> usbus0: 5.0Gbps Super Speed USB v3.0
> Timecounters tick every 1.000 msec
> hdacc0: <Cirrus Logic (0x4208) HDA CODEC> at cad 0 on hdac0
> hdaa0: <Cirrus Logic (0x4208) Audio Function Group> at nid 1 on
hdacc0
> pcm0: <Cirrus Logic (0x4208) (Analog)> at nid 18 and 24 on hdaa0
> pcm1: <Cirrus Logic (0x4208) (Analog Headphones)> at nid 16 on hdaa0
> pcm2: <Cirrus Logic (0x4208) (Analog Line-out)> at nid 19 on hdaa0
> pcm3: <Cirrus Logic (0x4208) (Digital)> at nid 33 on hdaa0
> usbus1: 480Mbps High Speed USB v2.0
> ugen0.1: <0x1b73> at usbus0
> uhub0: <0x1b73 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
usbus0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on
usbus1
> ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
> ada0: <APPLE SSD SM1024F UXM8JA1Q> ATA8-ACS SATA 3.x device
> ada0: Serial Number S1FVNYAF903719
> ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
> ada0: Command Queueing enabled
> ada0: 954204MB (1954210120 512 byte sectors: 16H 63S/T 16383C)
> ada0: Previously was known as ad4
> lapic1: Forcing LINT1 to edge trigger
> SMP: AP CPU #1 Launched!
> lapic6: Forcing LINT1 to edge trigger
> SMP: AP CPU #6 Launched!
> lapic7: Forcing LINT1 to edge trigger
> SMP: AP CPU #7 Launched!
> lapic3: Forcing LINT1 to edge trigger
> SMP: AP CPU #3 Launched!
> lapic19: Forcing LINT1 to edge trigger
> SMP: AP CPU #15 Launched!
> lapic22: Forcing LINT1 to edge trigger
> SMP: AP CPU #18 Launched!
> lapic26: Forcing LINT1 to edge trigger
> SMP: AP CPU #22 Launched!
> lapic23: Forcing LINT1 to edge trigger
> SMP: AP CPU #19 Launched!
> lapic9: Forcing LINT1 to edge trigger
> SMP: AP CPU #9 Launched!
> lapic27: Forcing LINT1 to edge trigger
> SMP: AP CPU #23 Launched!
> lapic24: Forcing LINT1 to edge trigger
> SMP: AP CPU #20 Launched!
> lapic25: Forcing LINT1 to edge trigger
> SMP: AP CPU #21 Launched!
> lapic10: Forcing LINT1 to edge trigger
> SMP: AP CPU #10 Launched!
> lapic4: Forcing LINT1 to edge trigger
> SMP: AP CPU #4 Launched!
> lapic5: Forcing LINT1 to edge trigger
> SMP: AP CPU #5 Launched!
> lapic18: Forcing LINT1 to edge trigger
> SMP: AP CPU #14 Launched!
> lapic8: Forcing LINT1 to edge trigger
> SMP: AP CPU #8 Launched!
> lapic11: Forcing LINT1 to edge trigger
> SMP: AP CPU #11 Launched!
> lapic17: Forcing LINT1 to edge trigger
> SMP: AP CPU #13 Launched!
> lapic2: Forcing LINT1 to edge trigger
> SMP: AP CPU #2 Launched!
> lapic16: Forcing LINT1 to edge trigger
> SMP: AP CPU #12 Launched!
> lapic21: Forcing LINT1 to edge trigger
> SMP: AP CPU #17 Launched!
> lapic20: Forcing LINT1 to edge trigger
> SMP: AP CPU #16 Launched!
> Timecounter "TSC-low" frequency 1350029784 Hz quality 1000
> Root mount waiting for: usbus1 usbus0
> uhub0: 8 ports with 8 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> ugen0.2: <Logitech> at usbus0
> Root mount waiting for: usbus1 usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr
2> on
> usbus1
> ugen0.3: <vendor 0x05ac> at usbus0
> uhub3: <vendor 0x05ac product 0x1008, class 9/0, rev 2.00/0.01, addr
2> on
> usbus0
> uhub3: 1 port with 1 removable, bus powered
> Root mount waiting for: usbus1 usbus0
> ugen0.4: <vendor 0x05ac> at usbus0
> uhub4: <vendor 0x05ac product 0x9132, class 9/0, rev 2.00/1.01, addr
3> on
> usbus0
> uhub4: MTT enabled
> uhub2: 8 ports with 7 removable, self powered
> uhub4: 3 ports with 2 removable, self powered
> Root mount waiting for: usbus1 usbus0
> ugen1.3: <Apple Inc.> at usbus1
> uhub5: <Apple Inc. BRCM20702 Hub, class 9/0, rev 2.00/1.00, addr 3>
on
> usbus1
> ugen0.5: <vendor 0x05ac> at usbus0
> hid_get_item: Number of items truncated to 255
> uhub5: 3 ports with 0 removable, self powered
> Root mount waiting for: usbus1 usbus0
> ugen1.4: <vendor 0x05ac> at usbus1
> ukbd0: <vendor 0x05ac product 0x820a, class 0/0, rev 2.00/1.00, addr
4> on
> usbus1
> kbd1 at ukbd0
> ugen0.6: <Apple, Inc.> at usbus0
> uhub6: <Apple, Inc. Keyboard Hub, class 9/0, rev 2.00/96.15, addr 5>
on
> usbus0
> uhub6: 3 ports with 2 removable, bus powered
> ugen1.5: <vendor 0x05ac> at usbus1
> Root mount waiting for: usbus1 usbus0
> ugen0.7: <Apple, Inc> at usbus0
> ukbd1: <Apple, Inc Apple Keyboard, class 0/0, rev 2.00/0.69, addr 6>
on
> usbus0
> kbd2 at ukbd1
> ugen1.6: <Apple Inc.> at usbus1
> Trying to mount root from ufs:/dev/ada0p2 [rw]...
> ums0: <Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 1>
on
> usbus0
> ums1: <vendor 0x05ac product 0x820b, class 0/0, rev 2.00/1.00, addr
5> on
> usbus1
> ums1: 3 buttons and [XY] coordinates ID=2
> ums0: 3 buttons and [XYZ] coordinates ID=0
> hid_get_item: Number of items truncated to 255
> hid_get_item: Number of items truncated to 255
> uhid0: <vendor 0x05ac product 0x9232, class 0/0, rev 1.10/1.14, addr
4> on
> usbus0
> hid_get_item: Number of items truncated to 255
> hid_get_item: Number of items truncated to 255
> hid_get_item: Number of items truncated to 255
> uhid1: <Apple, Inc Apple Keyboard, class 0/0, rev 2.00/0.69, addr 6>
on
> usbus0
> ubt0: <Apple Inc. Bluetooth USB Host Controller, rev 2.00/1.06, addr
6> on
> usbus1
> WARNING: attempt to domain_add(bluetooth) after domainfinalize()
> WARNING: attempt to domain_add(netgraph) after domainfinalize()
> ng_hci_send_command: ubt0hci - could not send HCI command, error=12
> ng_hci_process_command_timeout: ubt0hci - unable to complete HCI command
> OGF=0x3, OCF=0x3. Timeout
>
> Regards
> Estartu
>
> --
> _______________________________________________
> freebsd-stable at freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at
freebsd.org"
>