On Fri, Aug 20, 2010 at 01:44:20PM +0200, Nikola Kalpazanov
wrote:> Hi,
>
> First I want to start with the note that I know Realtek is no good,
> yet I will appreciate any assistance that you may provide.
>
> here are details of the problem:
>
> P811B is 4 port Ethernet card with built-in mini-PCI slot where I have
> attached Atheros 802.11a/b/g/n Wireless PCI Adapter (AR5416).
> That also requires to disable 4th port from the jumpers on the card.
>
> I have installed FreeBSD 8.1-RELEASE i386
>
> pciconf -vlb
>
> pcib6@pci0:5:0:0: class=0x060400 card=0x00000000 chip=0x814812d8
> rev=0x00 hdr=0x01
> vendor = 'Pericom Semiconductor'
> class = bridge
> subclass = PCI-PCI
> rl0@pci0:6:8:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10
hdr=0x00
> vendor = 'Realtek Semiconductor'
> device = 'Realtek RTL8139 Family PCI Fast Ethernet NIC
> (RTL-8139/8139C/8139D)'
> class = network
> subclass = ethernet
> bar [14] = type Memory, range 32, base 0xe0110200, size 256, enabled
> rl1@pci0:6:9:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10
hdr=0x00
> vendor = 'Realtek Semiconductor'
> device = 'Realtek RTL8139 Family PCI Fast Ethernet NIC
> (RTL-8139/8139C/8139D)'
> class = network
> subclass = ethernet
> bar [14] = type Memory, range 32, base 0xe0110100, size 256, enabled
> rl2@pci0:6:10:0: class=0x020000 card=0x813910ec chip=0x813910ec
> rev=0x10 hdr=0x00
> vendor = 'Realtek Semiconductor'
> device = 'Realtek RTL8139 Family PCI Fast Ethernet NIC
> (RTL-8139/8139C/8139D)'
> class = network
> subclass = ethernet
> bar [10] = type I/O Port, range 32, base 0x1000, size 256, enabled
> bar [14] = type Memory, range 32, base 0xe0110000, size 256, enabled
> ath0@pci0:6:11:0: class=0x028000 card=0x2071168c chip=0x0023168c
> rev=0x01 hdr=0x00
> vendor = 'Atheros Communications Inc.'
> device = '802.11a/b/g/n Wireless PCI Adapter (AR5416)'
> class = network
> bar [10] = type Memory, range 32, base 0xe0100000, size 65536,
enabled
>
>
>
> dmesg
>
> rl0: <RealTek 8139 10/100BaseTX> port 0x1200-0x12ff mem
> 0xe0110200-0xe01102ff irq 21 at device 8.0 on pci6
> rl0: reset never completed!
> rl0: unknown device ID: ffff assuming 8139
> rl0: MII without any phy!
> device_attach: rl0 attach returned 6
> rl1: <RealTek 8139 10/100BaseTX> port 0x1100-0x11ff mem
> 0xe0110100-0xe01101ff irq 22 at device 9.0 on pci6
> rl1: reset never completed!
> rl1: unknown device ID: ffff assuming 8139
> rl1: MII without any phy!
> device_attach: rl1 attach returned 6
> rl2: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem
> 0xe0110000-0xe01100ff irq 23 at device 10.0 on pci6
> miibus1: <MII bus> on rl2
> rlphy0: <RealTek internal media interface> PHY 0 on miibus1
> rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl2: Ethernet address: 00:06:4f:67:08:f5
> rl2: [ITHREAD]
> rl2: link state changed to DOWN
>
>
> ath0 works fine
> rl2 works fine
>
> rl0 and rl1 don't and of course as you may suspect they are missing
> from ifconfig -a
>
> if I remove the miniPCI Atheros and enable 4th port it is the same
> picture but this time 4th port rl3 works fine and rl0, rl1, and rl2
> don't in the same way.
>
> Any suggestions will be much appreciated.
What makes me wonder is that both pci0:6:8:0 and pci0:6:9:0 has no
I/O BAR. I never saw these kind of thing on rl(4) controllers.
And I can't explain how rl(4) could successfully map the I/O with
non-existing I/O BAR.
Anyway would you try attached patch and let me know whether it
makes any difference? Also add the following line to
/boot/device.hints to have rl(4) use memory mapped mapping.
hint.rl.0.prefer_iomap="0"
-------------- next part --------------
A non-text attachment was scrubbed...
Name: rl.map.diff
Type: text/x-diff
Size: 2314 bytes
Desc: not available
Url :
http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20100820/557b080e/rl.map.bin