Krassimir Slavchev
2009-Feb-17 09:48 UTC
Booting 7.1-STABLE on supermicro 5015-MF (PDSMI+)
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello All, It boots 7.1-RELEASE from the CDROM just fine but when boots from an IDE disk it crashes right after loading the kernel: http://mnemonic.bulinfo.net/~krassi/crash/supermicro_crash.jpg Booting from the USB produces exactly the same crash. I know that the BIOS of this board is buggy although it is latest. I am curious why it boots from the CDROM but cannot boots from the IDE disk. I just disconnect the CDROM and connect the IDE disk. The same IDE disk boots fine on other hardware. I have tried with 7.1-PRERELEASE which is 2-3 months older than 7.1-RELEASE and it crashes in same way. Any ideas what may be wrong? Best regards -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.7 (FreeBSD) iD8DBQFJmvhkxJBWvpalMpkRAmsAAJ4wh51lvt+nxllhCt69szOusEspuwCfU7ew TemmPRvVnGp68byH0I4d9lI=Md6S -----END PGP SIGNATURE-----
Krassimir Slavchev wrote, on 2/17/2009 8:48 AM:> It boots 7.1-RELEASE from the CDROM just fine but when boots from an IDE > disk it crashes right after loading the kernel: > > http://mnemonic.bulinfo.net/~krassi/crash/supermicro_crash.jpg > > Booting from the USB produces exactly the same crash. I know that the > BIOS of this board is buggy although it is latest. > I am curious why it boots from the CDROM but cannot boots from the IDE > disk. I just disconnect the CDROM and connect the IDE disk. The same IDE > disk boots fine on other hardware. I have tried with 7.1-PRERELEASE > which is 2-3 months older than 7.1-RELEASE and it crashes in same way.I see from the phot that you're running a custom kernel. What's different between that kernel and GENERIC? Data point: I'm running 7.1-RELEASE, installed from CD, on a PDSMI+ board, but I am booting from SATA. This may help to rule out possible non-IDE issues. I'm tracking with freebsd-update(8), but there have been no kernel updates yet. It's a fresh install with no kernel or sysctl tuning, and hasn't taken any load yet. $ uptime 10:02AM up 10 days, 18:50, 1 user, load averages: 0.00, 0.00, 0.00 $ uname -a FreeBSD dragonfly.acsalaska.net 7.1-RELEASE FreeBSD 7.1-RELEASE #0: Thu Jan 1 14:37:25 UTC 2009 root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386 $ cat /var/run/dmesg.boot Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.1-RELEASE #0: Thu Jan 1 14:37:25 UTC 2009 root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz (2394.01-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM> AMD Features=0x20100000<NX,LM> AMD Features2=0x1<LAHF> Cores per package: 2 real memory = 3756916736 (3582 MB) avail memory = 3672895488 (3502 MB) ACPI APIC Table: <PTLTD APIC > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 24-47 on motherboard kbd1 at kbdmux0 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) acpi0: <PTLTD RSDT> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 pci9: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci9 pci10: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0 pci13: <ACPI PCI bus> on pcib4 em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x4000-0x401f mem 0xe0200000-0xe021ffff irq 16 at device 0.0 on pci13 em0: Using MSI interrupt em0: [FILTER] em0: Ethernet address: 00:30:48:8d:30:74 pcib5: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0 pci14: <ACPI PCI bus> on pcib5 em1: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x5000-0x501f mem 0xe0300000-0xe031ffff irq 17 at device 0.0 on pci14 em1: Using MSI interrupt em1: [FILTER] em1: Ethernet address: 00:30:48:8d:30:75 uhci0: <UHCI (generic) USB controller> port 0x3000-0x301f irq 23 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0x3020-0x303f irq 19 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered uhci2: <UHCI (generic) USB controller> port 0x3040-0x305f irq 18 at device 29.2 on pci0 uhci2: [GIANT-LOCKED] uhci2: [ITHREAD] usb2: <UHCI (generic) USB controller> on uhci2 usb2: USB revision 1.0 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 uhub2: 2 ports with 2 removable, self powered uhci3: <UHCI (generic) USB controller> port 0x3060-0x307f irq 16 at device 29.3 on pci0 uhci3: [GIANT-LOCKED] uhci3: [ITHREAD] usb3: <UHCI (generic) USB controller> on uhci3 usb3: USB revision 1.0 uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 uhub3: 2 ports with 2 removable, self powered ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xe0000000-0xe00003ff irq 23 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4 uhub4: 8 ports with 8 removable, self powered pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci15: <ACPI PCI bus> on pcib6 vgapci0: <VGA-compatible display> port 0x6000-0x60ff mem 0xe8000000-0xefffffff,0xe0400000-0xe040ffff irq 16 at device 0.0 on pci15 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x30a0-0x30af at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] atapci1: <Intel ICH7 SATA300 controller> port 0x30e8-0x30ef,0x30dc-0x30df,0x30e0-0x30e7,0x30d8-0x30db,0x30b0-0x30bf mem 0xe0000400-0xe00007ff irq 19 at device 31.2 on pci0 atapci1: [ITHREAD] ata2: <ATA channel 0> on atapci1 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci1 ata3: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_button0: <Power Button> on acpi0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A, console sio0: [FILTER] sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A sio1: [FILTER] fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: does not respond device_attach: fdc0 attach returned 6 cpu0: <ACPI CPU> on acpi0 est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 921092106000921 device_attach: est0 attach returned 6 p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 921092106000921 device_attach: est1 attach returned 6 p4tcc1: <CPU Frequency Thermal Control> on cpu1 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: does not respond device_attach: fdc0 attach returned 6 pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xcb000-0xcbfff,0xcc000-0xccfff pnpid ORM0000 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: <Parallel port bus> on ppc0 ppbus0: [ITHREAD] plip0: <PLIP network interface> on ppbus0 plip0: WARNING: using obsoleted IFF_NEEDSGIANT flag lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ppc0: [GIANT-LOCKED] ppc0: [ITHREAD] sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 1.000 msec acd0: CDROM <CD-224E/1.9A> at ata0-master UDMA33 ad4: 238475MB <Seagate ST3250820AS 3.AAE> at ata2-master SATA150 ad6: 238475MB <Seagate ST3250820AS 3.AAE> at ata3-master SATA150 SMP: AP CPU #1 Launched! Trying to mount root from ufs:/dev/ad4s1a $ Royce