Hello,
I'm building a new system with an AMD Phenom 9350e Quad-Core:
FreeBSD phenom.example.net 7.1-PRERELEASE FreeBSD 7.1-PRERELEASE #0:
Tue Aug 26 19:49:24 UTC 2008 root@phenom.example.net:/usr/obj/usr/\
src/sys/GENERIC i386
Everything's running smoothly, until I start powerd. As soon as
that happens, the system freezes hard. Trying powerd in the foreground
with -v shows that it decreased the frequencies a few times, but then
hangs the system.
So I've tried this manually:
# sysctl dev.cpu.0.freq_levels
dev.cpu.0.freq_levels: 1985/-1 1736/-1 1488/-1 1240/-1 992/-1 744/-1
496/-1 248/-1
# sysctl dev.cpu.0.freq
dev.cpu.0.freq: 1985
powerd freezed the system after reaching 1240 when trying 992. If I set
the frequency manually down to 1240 with:
# sysctl dev.cpu.0.freq=1240
everything's fine. But as soon as I try setting it further down
(992, 744, 496 or 248), the system freezes too, just the same
as with powerd. This is 100% reproducible.
So what's going on here?
Thanks,
-cpghost.
Oh, here's dmesg, if it helps:
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-PRERELEASE #0: Tue Aug 26 19:49:24 UTC 2008
root@phenom.example.net:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Phenom(tm) 9350e Quad-Core Processor (1995.68-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x100f23 Stepping = 3
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x802009<SSE3,MON,CX16,<b23>>
AMD
Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,<b26>,RDTSCP,LM,3DNow!+,3DNow!>
AMD
Features2=0x7ff<LAHF,CMP,SVM,ExtAPIC,CR8,<b5>,<b6>,<b7>,Prefetch,<b9>,<b10>>
Cores per package: 4
real memory = 2079916032 (1983 MB)
avail memory = 2025545728 (1931 MB)
ACPI APIC Table: <052808 APIC1156>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <052808 RSDT1156> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of fff00000, 100000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7bf00000 (3) failed
ACPI HPET table warning: Sequence is non-zero (2)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xc000-0xc0ff mem
0xf8000000-0xfbffffff,0xfe8f0000-0xfe8fffff,0xfe700000-0xfe7fffff irq 18 at
device 5.0 on pci1
pcm0: <ATI (Unknown) High Definition Audio Controller> mem
0xfe8e8000-0xfe8ebfff irq 19 at device 5.1 on pci1
pcm0: [ITHREAD]
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 5.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0
pci3: <ACPI PCI bus> on pcib3
ohci0: <OHCI (generic) USB controller> mem 0xfe6ff000-0xfe6fffff irq 16 at
device 18.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfe6fe000-0xfe6fefff irq 16 at
device 18.1 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe6fd800-0xfe6fd8ff irq
17 at device 18.2 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 3 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 6 ports with 6 removable, self powered
ohci2: <OHCI (generic) USB controller> mem 0xfe6fc000-0xfe6fcfff irq 18 at
device 19.0 on pci0
ohci2: [GIANT-LOCKED]
ohci2: [ITHREAD]
usb3: OHCI version 1.0, legacy support
usb3: SMM does not respond, resetting
usb3: <OHCI (generic) USB controller> on ohci2
usb3: USB revision 1.0
uhub3: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 3 ports with 3 removable, self powered
ohci3: <OHCI (generic) USB controller> mem 0xfe6fb000-0xfe6fbfff irq 18 at
device 19.1 on pci0
ohci3: [GIANT-LOCKED]
ohci3: [ITHREAD]
usb4: OHCI version 1.0, legacy support
usb4: SMM does not respond, resetting
usb4: <OHCI (generic) USB controller> on ohci3
usb4: USB revision 1.0
uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 3 ports with 3 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe6fd000-0xfe6fd0ff irq
19 at device 19.2 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb5: EHCI version 1.0
usb5: companion controllers, 3 ports each: usb3 usb4
usb5: <EHCI (generic) USB 2.0 controller> on ehci1
usb5: USB revision 2.0
uhub5: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5
uhub5: 6 ports with 6 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci0: <ATI IXP700 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
pcm1: <ATI SB600 High Definition Audio Controller> mem
0xfe6f4000-0xfe6f7fff irq 16 at device 20.2 on pci0
pcm1: [ITHREAD]
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci4: <ACPI PCI bus> on pcib4
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem
0xfebffc00-0xfebffcff irq 21 at device 6.0 on pci4
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> PHY 0 on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:50:ba:bb:48:46
rl0: [ITHREAD]
ohci4: <OHCI (generic) USB controller> mem 0xfe6fa000-0xfe6fafff irq 18 at
device 20.5 on pci0
ohci4: [GIANT-LOCKED]
ohci4: [ITHREAD]
usb6: OHCI version 1.0, legacy support
usb6: SMM does not respond, resetting
usb6: <OHCI (generic) USB controller> on ohci4
usb6: USB revision 1.0
uhub6: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6
uhub6: 2 ports with 2 removable, self powered
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse Explorer, device ID 4
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pmtimer0 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
ad0: 76319MB <SAMSUNG SP0842N BH100-45> at ata0-master UDMA100
acd0: DVDR <Optiarc DVD RW AD-7203A/1.01> at ata0-slave UDMA66
pcm0: <HDA Codec: Unknown Codec>
pcm0: <HDA Driver Revision: 20080420_0052>
pcm1: <HDA Codec: Realtek ALC888>
pcm1: <HDA Driver Revision: 20080420_0052>
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad0s1a
rl0: link state changed to UP
pcm0: detached
pcm1: detached
pcm0: <ATI SB600 High Definition Audio Controller> mem
0xfe6f4000-0xfe6f7fff irq 16 at device 20.2 on pci0
pcm0: [ITHREAD]
pcm0: <HDA Codec: Realtek ALC888>
pcm0: <HDA Driver Revision: 20080420_0052>
pcm1: <ATI (Unknown) High Definition Audio Controller> mem
0xfe8e8000-0xfe8ebfff irq 19 at device 5.1 on pci1
pcm1: [ITHREAD]
pcm1: <HDA Codec: Unknown Codec>
pcm1: <HDA Driver Revision: 20080420_0052>
--
Cordula's Web. http://www.cordula.ws/