Hi,
I'm trying to get a PCI-express add-in parallel port card working with
7.0-STABLE, and after trying the following, I'm unable to get it to
attach to the ppc bus. The card has a "MosChip NM9805" chip.
Motherboard
is an ASUS P5E64 WS. (which of course has no on-board parallel port).
The card seems to be recognised by the puc layer.
I've added
device puc
to the kernel config file, and added
{ 0x9710, 0x9805, 0xffff, 0,
"MosChip NM9805 Dual 1284 Printer port",
0,
PUC_PORT_2P, 0x10, 8, 0,
},
to sys/dev/puc/pucdata.c and with verbose booting, get the following
extracts from dmesg: (full dmesg attached below)
pcib3: slot 0 INTB hardwired to IRQ 17
pcib4: slot 1 INTA is routed to irq 17
pcib5: slot 0 INTA is routed to irq 17
pcib6: slot 0 INTA is routed to irq 17
ppc0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xdc00
ppc0: using extended I/O port range
puc0: <MosChip NM9805 Dual 1284 Printer port> port
0xdc00-0xdc07,0xd880-0xd887,0xd800-0xd807,0xd480-0xd487,0xd400-0xd407,0xd080-0xd08f
irq 17 at device 0.0 on pci10
pcib6: puc0 requested I/O range 0xdc00-0xdc07: in range
pcib5: puc0 requested I/O range 0xdc00-0xdc07: in range
pcib4: puc0 requested I/O range 0xdc00-0xdc07: in range
pcib3: puc0 requested I/O range 0xdc00-0xdc07: in range
puc0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xd800
puc0: [FILTER]
ppc0: using extended I/O port range
ppc0: using extended I/O port range
[ and later ]
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
Any suggestions would be appreciated.
--
Richard
-------------- next part --------------
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-STABLE #8: Sat Mar 29 16:40:32 EST 2008
rpp@marvin.ci.com.au:/u3/obj/usr/src/sys/LOCAL
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0ef1000.
Preloaded elf module "/boot/kernel/snd_driver.ko" at 0xc0ef1188.
Preloaded elf module "/boot/kernel/snd_ad1816.ko" at 0xc0ef1238.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc0ef12e8.
Preloaded elf module "/boot/kernel/snd_als4000.ko" at 0xc0ef1394.
Preloaded elf module "/boot/kernel/snd_atiixp.ko" at 0xc0ef1444.
Preloaded elf module "/boot/kernel/snd_cmi.ko" at 0xc0ef14f4.
Preloaded elf module "/boot/kernel/snd_cs4281.ko" at 0xc0ef15a0.
Preloaded elf module "/boot/kernel/snd_csa.ko" at 0xc0ef1650.
Preloaded elf module "/boot/kernel/snd_ds1.ko" at 0xc0ef16fc.
Preloaded elf module "/boot/kernel/snd_emu10kx.ko" at 0xc0ef17a8.
Preloaded elf module "/boot/kernel/snd_envy24.ko" at 0xc0ef1858.
Preloaded elf module "/boot/kernel/snd_spicds.ko" at 0xc0ef1908.
Preloaded elf module "/boot/kernel/snd_envy24ht.ko" at 0xc0ef19b8.
Preloaded elf module "/boot/kernel/snd_es137x.ko" at 0xc0ef1a6c.
Preloaded elf module "/boot/kernel/snd_ess.ko" at 0xc0ef1b1c.
Preloaded elf module "/boot/kernel/snd_sbc.ko" at 0xc0ef1bc8.
Preloaded elf module "/boot/kernel/snd_fm801.ko" at 0xc0ef1c74.
Preloaded elf module "/boot/kernel/snd_mss.ko" at 0xc0ef1d24.
Preloaded elf module "/boot/kernel/snd_hda.ko" at 0xc0ef1dd0.
Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0ef1e7c.
Preloaded elf module "/boot/kernel/snd_maestro.ko" at 0xc0ef1f28.
Preloaded elf module "/boot/kernel/snd_maestro3.ko" at 0xc0ef1fd8.
Preloaded elf module "/boot/kernel/snd_neomagic.ko" at 0xc0ef208c.
Preloaded elf module "/boot/kernel/snd_sb16.ko" at 0xc0ef2140.
Preloaded elf module "/boot/kernel/snd_sb8.ko" at 0xc0ef21f0.
Preloaded elf module "/boot/kernel/snd_solo.ko" at 0xc0ef229c.
Preloaded elf module "/boot/kernel/snd_t4dwave.ko" at 0xc0ef234c.
Preloaded elf module "/boot/kernel/snd_via8233.ko" at 0xc0ef23fc.
Preloaded elf module "/boot/kernel/snd_via82c686.ko" at 0xc0ef24ac.
Preloaded elf module "/boot/kernel/snd_vibes.ko" at 0xc0ef2560.
Preloaded elf module "/boot/kernel/atapicam.ko" at 0xc0ef2610.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0ef26c0.
Calibrating clock(s) ... i8254 clock: 1193200 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2999672289 Hz
CPU: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz (2999.67-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6fb Stepping = 11
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3fd<SSE3,RSVD2,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Cores per package: 2
Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries
1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size
1st-level data cache: 32 KB, 8-way set associative, 64 byte line size
L2 cache: 4096 kbytes, 16-way associative, 64 bytes/line
real memory = 2146697216 (2047 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001028000 - 0x000000007dae2fff, 2091626496 bytes (510651 pages)
avail memory = 2091003904 (1994 MB)
Table 'FACP' at 0x7ff40200
Table 'APIC' at 0x7ff40390
MADT: Found table at 0x7ff40390
MP Configuration Table version 1.4 found at 0xc00f1540
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 2: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 130 ACPI ID 3: disabled
MADT: Found CPU APIC ID 131 ACPI ID 4: disabled
ACPI APIC Table: <A_M_I_ OEMAPIC >
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x31
pnpbios: Found PnP BIOS data at 0xc00f7040
pnpbios: Entry = f0000:803a Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
ULE: setup cpu group 0
ULE: setup cpu 0
ULE: adding cpu 0 to group 0: cpus 1 mask 0x1
ULE: setup cpu group 1
ULE: setup cpu 1
ULE: adding cpu 1 to group 1: cpus 1 mask 0x2
ACPI: RSDP @ 0x0xfaff0/0x0014 (v 0 ACPIAM)
ACPI: RSDT @ 0x0x7ff40000/0x003C (v 1 A_M_I_ OEMRSDT 0x11000728 MSFT
0x00000097)
ACPI: FACP @ 0x0x7ff40200/0x0084 (v 2 A_M_I_ OEMFACP 0x11000728 MSFT
0x00000097)
ACPI: DSDT @ 0x0x7ff40440/0x9098 (v 1 A0870 A0870031 0x00000031 INTL
0x20060113)
ACPI: FACS @ 0x0x7ff4e000/0x0040
ACPI: APIC @ 0x0x7ff40390/0x006C (v 1 A_M_I_ OEMAPIC 0x11000728 MSFT
0x00000097)
ACPI: MCFG @ 0x0x7ff40400/0x003C (v 1 A_M_I_ OEMMCFG 0x11000728 MSFT
0x00000097)
ACPI: OEMB @ 0x0x7ff4e040/0x0081 (v 1 A_M_I_ AMI_OEM 0x11000728 MSFT
0x00000097)
ACPI: HPET @ 0x0x7ff494e0/0x0038 (v 1 A_M_I_ OEMHPET 0x11000728 MSFT
0x00000097)
ACPI: OSFR @ 0x0x7ff49520/0x00B0 (v 1 A_M_I_ OEMOSFR 0x11000728 MSFT
0x00000097)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010000
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
wlan_amrr: <AMRR Transmit Rate Control Algorithm>
wlan: <802.11 Link Layer>
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5
feeder_buffersize=16384 feeder_rate_min=1 feeder_rate_max=2016000
feeder_rate_round=25
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
crypto: <crypto core>
kbd: new array size 4
kbd1 at kbdmux0
io: <I/O>
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Mar 29 2008 16:39:27)
npx0: INT 16 interface
cryptosoft0: <software crypto> on motherboard
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
acpi0: <A_M_I_ OEMRSDT> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xd90a7000 pa 0x1000
acpi: bad write to port 0x080 (16), val 0xaa
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000094
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=29e08086)
pcibios: BIOS version 3.00
AcpiOsDerivePciId: \\_SB_.PCI0.SBRG.IELK.RXA0 -> bus 0 dev 0 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.SBRG.FHR0 -> bus 0 dev 31 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.SBRG.PIX0 -> bus 0 dev 31 func 0
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7ff00000 (3) failed
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 11 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 10 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 5 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 15 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 15 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 3 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 3 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 7 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 7 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 14 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 14 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
acpi_hpet0: vend: 0x8086 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route 64-bit
Timecounter "HPET" frequency 14318180 Hz quality 900
cpu0: <ACPI CPU> on acpi0
ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] - BE, should be
B5 [20070320]
ACPI: SSDT @ 0x0x7ff4e0d0/0x01D2 (v 1 AMI CPU1PM 0x00000001 INTL
0x20060113)
cpu0: switching to generic Cx mode
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
ACPI: SSDT @ 0x0x7ff4e2b0/0x0143 (v 1 AMI CPU2PM 0x00000001 INTL
0x20060113)
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est1: Invalid id16 (set, cur) = (2344, 1576)
est1: Invalid freq 2997, ignored.
est1: Invalid id16 (set, cur) = (1559, 2327)
est1: Invalid freq 1998, ignored.
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x29e0, revid=0x01
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x29e1, revid=0x01
domain=0, bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 3 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x29e9, revid=0x01
domain=0, bus=0, slot=6, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 3 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.6.INTA
pcib0: slot 6 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2937, revid=0x02
domain=0, bus=0, slot=26, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[20]: type I/O Port, range 32, base 0x8800, size 5, enabled
pcib0: matched entry for 0.26.INTA
pcib0: slot 26 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2938, revid=0x02
domain=0, bus=0, slot=26, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=3
map[20]: type I/O Port, range 32, base 0x8880, size 5, enabled
pcib0: matched entry for 0.26.INTB
pcib0: slot 26 INTB hardwired to IRQ 21
found-> vendor=0x8086, dev=0x2939, revid=0x02
domain=0, bus=0, slot=26, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=5
map[20]: type I/O Port, range 32, base 0x8c00, size 5, enabled
pcib0: matched entry for 0.26.INTC
pcib0: slot 26 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x293c, revid=0x02
domain=0, bus=0, slot=26, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xfe2ffc00, size 10, enabled
pcib0: matched entry for 0.26.INTC
pcib0: slot 26 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x293e, revid=0x02
domain=0, bus=0, slot=27, func=0
class=04-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=7
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 64, base 0xfe2f8000, size 14, enabled
pcib0: matched entry for 0.27.INTA
pcib0: slot 27 INTA hardwired to IRQ 22
found-> vendor=0x8086, dev=0x2940, revid=0x02
domain=0, bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 17
found-> vendor=0x8086, dev=0x2948, revid=0x02
domain=0, bus=0, slot=28, func=4
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 17
found-> vendor=0x8086, dev=0x294a, revid=0x02
domain=0, bus=0, slot=28, func=5
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTB
pcib0: slot 28 INTB hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2934, revid=0x02
domain=0, bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=14
map[20]: type I/O Port, range 32, base 0x8080, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
found-> vendor=0x8086, dev=0x2935, revid=0x02
domain=0, bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=15
map[20]: type I/O Port, range 32, base 0x8400, size 5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 19
found-> vendor=0x8086, dev=0x2936, revid=0x02
domain=0, bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=5
map[20]: type I/O Port, range 32, base 0x8480, size 5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x293a, revid=0x02
domain=0, bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=14
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xfe2ff800, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
found-> vendor=0x8086, dev=0x244e, revid=0x92
domain=0, bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2916, revid=0x02
domain=0, bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2930, revid=0x02
domain=0, bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=5
map[10]: type Memory, range 64, base 0xfe2ff400, size 8, enabled
map[20]: type I/O Port, range 32, base 0x400, size 5, enabled
pcib0: matched entry for 0.31.INTC
pcib0: slot 31 INTC hardwired to IRQ 18
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0x9000-0x9fff
pcib1: memory decode 0xfe300000-0xfe3fffff
pcib1: prefetched decode 0xd0000000-0xdfffffff
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x1002, dev=0x94c3, revid=0x00
domain=0, bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Prefetchable Memory, range 64, base 0xd0000000, size 28, enabled
pcib1: requested memory range 0xd0000000-0xdfffffff: good
map[18]: type Memory, range 64, base 0xfe3e0000, size 16, enabled
pcib1: requested memory range 0xfe3e0000-0xfe3effff: good
map[20]: type I/O Port, range 32, base 0x9000, size 8, enabled
pcib1: requested I/O range 0x9000-0x90ff: in range
pcib1: matched entry for 1.0.INTA
pcib1: slot 0 INTA hardwired to IRQ 16
found-> vendor=0x1002, dev=0xaa10, revid=0x00
domain=0, bus=1, slot=0, func=1
class=04-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 64, base 0xfe3fc000, size 14, enabled
pcib1: requested memory range 0xfe3fc000-0xfe3fffff: good
pcib1: matched entry for 1.0.INTB
pcib1: slot 0 INTB hardwired to IRQ 17
vgapci0: <VGA-compatible display> port 0x9000-0x90ff mem
0xd0000000-0xdfffffff,0xfe3e0000-0xfe3effff irq 16 at device 0.0 on pci1
pcm0: <ATI (Unknown) High Definition Audio Controller> mem
0xfe3fc000-0xfe3fffff irq 17 at device 0.1 on pci1
pcm0: DMA Coherency: Uncacheable / vendor=0x1002
pcm0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xfe3fc000
ioapic0: routing intpin 17 (PCI IRQ 17) to vector 49
pcm0: [MPSAFE]
pcm0: [ITHREAD]
pcm0: hdac_dma_alloc: size=1024 -> roundsz=1024
pcm0: hdac_dma_alloc: size=2048 -> roundsz=2048
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 6.0 on pci0
pcib2: domain 0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xa000-0xafff
pcib2: memory decode 0xfe400000-0xfe7fffff
pcib2: no prefetched decode
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x1000, dev=0x0056, revid=0x04
domain=0, bus=2, slot=0, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
MSI-X supports 1 message in map 0x14
map[10]: type I/O Port, range 32, base 0xa800, size 8, enabled
pcib2: requested I/O range 0xa800-0xa8ff: in range
map[14]: type Memory, range 64, base 0xfe7fc000, size 14, enabled
pcib2: requested memory range 0xfe7fc000-0xfe7fffff: good
map[1c]: type Memory, range 64, base 0xfe7e0000, size 16, enabled
pcib2: requested memory range 0xfe7e0000-0xfe7effff: good
pcib2: matched entry for 2.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 16
mpt0: <LSILogic SAS/SATA Adapter> port 0xa800-0xa8ff mem
0xfe7fc000-0xfe7fffff,0xfe7e0000-0xfe7effff irq 16 at device 0.0 on pci2
mpt0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xa800
mpt0: Reserved 0x4000 bytes for rid 0x14 type 3 at 0xfe7fc000
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 50
mpt0: [MPSAFE]
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.17.0
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
uhci0: <UHCI (generic) USB controller> port 0x8800-0x881f irq 16 at device
26.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x8800
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x8880-0x889f irq 21 at device
26.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x8880
ioapic0: routing intpin 21 (PCI IRQ 21) to vector 51
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x8c00-0x8c1f irq 18 at device
26.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x8c00
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 52
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe2ffc00-0xfe2fffff irq
18 at device 26.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfe2ffc00
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pcm1: <Intel 82801I High Definition Audio Controller> mem
0xfe2f8000-0xfe2fbfff irq 22 at device 27.0 on pci0
pcm1: TCSEL: 0x07 -> 0x00
pcm1: DMA Coherency: Uncacheable / vendor=0x8086
pcm1: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xfe2f8000
ioapic0: routing intpin 22 (PCI IRQ 22) to vector 53
pcm1: [MPSAFE]
pcm1: [ITHREAD]
pcm1: hdac_dma_alloc: size=1024 -> roundsz=1024
pcm1: hdac_dma_alloc: size=2048 -> roundsz=2048
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pcib3: domain 0
pcib3: secondary bus 5
pcib3: subordinate bus 10
pcib3: I/O decode 0xd000-0xdfff
pcib3: memory decode 0xfea00000-0xfeafffff
pcib3: prefetched decode 0xfde00000-0xfdffffff
pci5: <ACPI PCI bus> on pcib3
pci5: domain=0, physical bus=5
found-> vendor=0x10b5, dev=0x8518, revid=0xac
domain=0, bus=5, slot=0, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 3 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 32, base 0xfeae0000, size 17, enabled
pcib3: requested memory range 0xfeae0000-0xfeafffff: good
pcib3: matched entry for 5.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 16
pcib4: <ACPI PCI-PCI bridge> mem 0xfeae0000-0xfeafffff irq 16 at device
0.0 on pci5
pcib4: domain 0
pcib4: secondary bus 6
pcib4: subordinate bus 10
pcib4: I/O decode 0xd000-0xdfff
pcib4: prefetched decode 0xfde00000-0xfdffffff
pcib4: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P4.P4PB -
AE_NOT_FOUND
pci6: <ACPI PCI bus> on pcib4
pci6: domain=0, physical bus=6
found-> vendor=0x10b5, dev=0x8518, revid=0xac
domain=0, bus=6, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0105, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 3 supports D0 D3 current D0
MSI supports 1 message, 64 bit
pcib3: matched entry for 5.0.INTB
pcib3: slot 0 INTB hardwired to IRQ 17
pcib4: slot 1 INTA is routed to irq 17
found-> vendor=0x10b5, dev=0x8518, revid=0xac
domain=0, bus=6, slot=2, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0106, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 3 supports D0 D3 current D0
MSI supports 1 message, 64 bit
pcib3: matched entry for 5.0.INTC
pcib3: slot 0 INTC hardwired to IRQ 18
pcib4: slot 2 INTA is routed to irq 18
found-> vendor=0x10b5, dev=0x8518, revid=0xac
domain=0, bus=6, slot=3, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0106, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
powerspec 3 supports D0 D3 current D0
MSI supports 1 message, 64 bit
pcib3: matched entry for 5.0.INTD
pcib3: slot 0 INTD hardwired to IRQ 19
pcib4: slot 3 INTA is routed to irq 19
pcib5: <PCI-PCI bridge> irq 17 at device 1.0 on pci6
pcib5: domain 0
pcib5: secondary bus 9
pcib5: subordinate bus 10
pcib5: I/O decode 0xd000-0xdfff
pcib5: no prefetched decode
pci9: <PCI bus> on pcib5
pci9: domain=0, physical bus=9
found-> vendor=0x10b5, dev=0x8111, revid=0x21
domain=0, bus=9, slot=0, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0115, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
MSI supports 1 message, 64 bit
pcib3: matched entry for 5.0.INTB
pcib3: slot 0 INTB hardwired to IRQ 17
pcib4: slot 1 INTA is routed to irq 17
pcib5: slot 0 INTA is routed to irq 17
pcib6: <PCI-PCI bridge> irq 17 at device 0.0 on pci9
pcib6: domain 0
pcib6: secondary bus 10
pcib6: subordinate bus 10
pcib6: I/O decode 0xd000-0xdfff
pcib6: no prefetched decode
pci10: <PCI bus> on pcib6
pci10: domain=0, physical bus=10
found-> vendor=0x9710, dev=0x9805, revid=0x01
domain=0, bus=10, slot=0, func=0
class=07-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[10]: type I/O Port, range 32, base 0xdc00, size 3, enabled
pcib6: requested I/O range 0xdc00-0xdc07: in range
pcib5: requested I/O range 0xdc00-0xdc07: in range
pcib4: requested I/O range 0xdc00-0xdc07: in range
pcib3: requested I/O range 0xdc00-0xdc07: in range
map[14]: type I/O Port, range 32, base 0xd880, size 3, enabled
pcib6: requested I/O range 0xd880-0xd887: in range
pcib5: requested I/O range 0xd880-0xd887: in range
pcib4: requested I/O range 0xd880-0xd887: in range
pcib3: requested I/O range 0xd880-0xd887: in range
map[18]: type I/O Port, range 32, base 0xd800, size 3, enabled
pcib6: requested I/O range 0xd800-0xd807: in range
pcib5: requested I/O range 0xd800-0xd807: in range
pcib4: requested I/O range 0xd800-0xd807: in range
pcib3: requested I/O range 0xd800-0xd807: in range
map[1c]: type I/O Port, range 32, base 0xd480, size 3, enabled
pcib6: requested I/O range 0xd480-0xd487: in range
pcib5: requested I/O range 0xd480-0xd487: in range
pcib4: requested I/O range 0xd480-0xd487: in range
pcib3: requested I/O range 0xd480-0xd487: in range
map[20]: type I/O Port, range 32, base 0xd400, size 3, enabled
pcib6: requested I/O range 0xd400-0xd407: in range
pcib5: requested I/O range 0xd400-0xd407: in range
pcib4: requested I/O range 0xd400-0xd407: in range
pcib3: requested I/O range 0xd400-0xd407: in range
map[24]: type I/O Port, range 32, base 0xd080, size 4, enabled
pcib6: requested I/O range 0xd080-0xd08f: in range
pcib5: requested I/O range 0xd080-0xd08f: in range
pcib4: requested I/O range 0xd080-0xd08f: in range
pcib3: requested I/O range 0xd080-0xd08f: in range
pcib3: matched entry for 5.0.INTB
pcib3: slot 0 INTB hardwired to IRQ 17
pcib4: slot 1 INTA is routed to irq 17
pcib5: slot 0 INTA is routed to irq 17
pcib6: slot 0 INTA is routed to irq 17
ppc0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xdc00
ppc0: using extended I/O port range
puc0: <MosChip NM9805 Dual 1284 Printer port> port
0xdc00-0xdc07,0xd880-0xd887,0xd800-0xd807,0xd480-0xd487,0xd400-0xd407,0xd080-0xd08f
irq 17 at device 0.0 on pci10
pcib6: puc0 requested I/O range 0xdc00-0xdc07: in range
pcib5: puc0 requested I/O range 0xdc00-0xdc07: in range
pcib4: puc0 requested I/O range 0xdc00-0xdc07: in range
pcib3: puc0 requested I/O range 0xdc00-0xdc07: in range
puc0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xd800
puc0: [FILTER]
ppc0: using extended I/O port range
ppc0: using extended I/O port range
pcib7: <PCI-PCI bridge> irq 18 at device 2.0 on pci6
pcib7: domain 0
pcib7: secondary bus 8
pcib7: subordinate bus 8
pcib7: I/O decode 0x0-0x0
pcib7: prefetched decode 0xfdf00000-0xfdffffff
pci8: <PCI bus> on pcib7
pci8: domain=0, physical bus=8
pcib8: <PCI-PCI bridge> irq 19 at device 3.0 on pci6
pcib8: domain 0
pcib8: secondary bus 7
pcib8: subordinate bus 7
pcib8: I/O decode 0x0-0x0
pcib8: prefetched decode 0xfde00000-0xfdefffff
pci7: <PCI bus> on pcib8
pci7: domain=0, physical bus=7
pcib9: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0
pcib9: domain 0
pcib9: secondary bus 4
pcib9: subordinate bus 4
pcib9: I/O decode 0xc000-0xcfff
pcib9: memory decode 0xfe900000-0xfe9fffff
pcib9: no prefetched decode
pci4: <ACPI PCI bus> on pcib9
pci4: domain=0, physical bus=4
found-> vendor=0x11ab, dev=0x6145, revid=0xa1
domain=0, bus=4, slot=0, func=0
class=01-01-8f, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D3 current D0
MSI supports 1 message
map[10]: type I/O Port, range 32, base 0xcc00, size 3, enabled
pcib9: requested I/O range 0xcc00-0xcc07: in range
map[14]: type I/O Port, range 32, base 0xc880, size 2, enabled
pcib9: requested I/O range 0xc880-0xc883: in range
map[18]: type I/O Port, range 32, base 0xc800, size 3, enabled
pcib9: requested I/O range 0xc800-0xc807: in range
map[1c]: type I/O Port, range 32, base 0xc480, size 2, enabled
pcib9: requested I/O range 0xc480-0xc483: in range
map[20]: type I/O Port, range 32, base 0xc400, size 4, enabled
pcib9: requested I/O range 0xc400-0xc40f: in range
map[24]: type Memory, range 32, base 0xfe9ffc00, size 10, enabled
pcib9: requested memory range 0xfe9ffc00-0xfe9fffff: good
pcib9: matched entry for 4.0.INTA
pcib9: slot 0 INTA hardwired to IRQ 16
atapci0: <Marvell 88SX6145 UDMA133 controller> port
0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc807,0xc480-0xc483,0xc400-0xc40f mem
0xfe9ffc00-0xfe9fffff irq 16 at device 0.0 on pci4
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xc400
atapci0: [MPSAFE]
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xcc00
atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xc880
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata2: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xc800
atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xc480
ata3: reset tp1 mask=03 ostat0=7f ostat1=7f
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata3: reset tp2 stat0=ff stat1=ff devices=0x0
ata3: [MPSAFE]
ata3: [ITHREAD]
pcib10: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0
pcib10: domain 0
pcib10: secondary bus 3
pcib10: subordinate bus 3
pcib10: I/O decode 0xb000-0xbfff
pcib10: memory decode 0xfe800000-0xfe8fffff
pcib10: no prefetched decode
pci3: <ACPI PCI bus> on pcib10
pci3: domain=0, physical bus=3
found-> vendor=0x11ab, dev=0x4364, revid=0x12
domain=0, bus=3, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 64, base 0xfe8fc000, size 14, enabled
pcib10: requested memory range 0xfe8fc000-0xfe8fffff: good
map[18]: type I/O Port, range 32, base 0xb800, size 8, enabled
pcib10: requested I/O range 0xb800-0xb8ff: in range
pcib10: matched entry for 3.0.INTA
pcib10: slot 0 INTA hardwired to IRQ 17
mskc0: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0xb800-0xb8ff mem
0xfe8fc000-0xfe8fffff irq 17 at device 0.0 on pci3
mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xfe8fc000
mskc0: MSI count : 1
mskc0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 256 to vector 54
mskc0: using IRQ 256 for MSI
mskc0: RAM buffer size : 128KB
mskc0: Port 0 : Rx Queue 85KB(0x00000000:0x000153ff)
mskc0: Port 0 : Tx Queue 43KB(0x00015400:0x0001ffff)
msk0: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x03> on
mskc0
msk0: bpf attached
msk0: Ethernet address: 00:1e:8c:75:1c:8e
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
mskc0: [MPSAFE]
mskc0: [FILTER]
uhci3: <UHCI (generic) USB controller> port 0x8080-0x809f irq 23 at device
29.0 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x8080
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 55
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb4: <UHCI (generic) USB controller> on uhci3
usb4: USB revision 1.0
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
uhci4: <UHCI (generic) USB controller> port 0x8400-0x841f irq 19 at device
29.1 on pci0
uhci4: Reserved 0x20 bytes for rid 0x20 type 4 at 0x8400
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 56
uhci4: [GIANT-LOCKED]
uhci4: [ITHREAD]
usb5: <UHCI (generic) USB controller> on uhci4
usb5: USB revision 1.0
uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5
uhub5: 2 ports with 2 removable, self powered
uhci5: <UHCI (generic) USB controller> port 0x8480-0x849f irq 18 at device
29.2 on pci0
uhci5: Reserved 0x20 bytes for rid 0x20 type 4 at 0x8480
uhci5: [GIANT-LOCKED]
uhci5: [ITHREAD]
usb6: <UHCI (generic) USB controller> on uhci5
usb6: USB revision 1.0
uhub6: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6
uhub6: 2 ports with 2 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe2ff800-0xfe2ffbff irq
23 at device 29.7 on pci0
ehci1: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfe2ff800
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb7: EHCI version 1.0
usb7: companion controllers, 2 ports each: usb4 usb5 usb6
usb7: <EHCI (generic) USB 2.0 controller> on ehci1
usb7: USB revision 2.0
uhub7: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb7
uhub7: 6 ports with 6 removable, self powered
pcib11: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib11: domain 0
pcib11: secondary bus 11
pcib11: subordinate bus 11
pcib11: I/O decode 0xe000-0xefff
pcib11: memory decode 0xfeb00000-0xfebfffff
pcib11: no prefetched decode
pcib11: Subtractively decoded bridge.
pci11: <ACPI PCI bus> on pcib11
pci11: domain=0, physical bus=11
found-> vendor=0x9005, dev=0x00c0, revid=0x01
domain=0, bus=11, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type I/O Port, range 32, base 0xe000, size 8, enabled
pcib11: requested I/O range 0xe000-0xe0ff: in range
map[14]: type Memory, range 64, base 0xfebf9000, size 12, enabled
pcib11: requested memory range 0xfebf9000-0xfebf9fff: good
pcib11: matched entry for 11.1.INTA
pcib11: slot 1 INTA hardwired to IRQ 17
found-> vendor=0x9005, dev=0x00c0, revid=0x01
domain=0, bus=11, slot=1, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=b, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type I/O Port, range 32, base 0xe400, size 8, enabled
pcib11: requested I/O range 0xe400-0xe4ff: in range
map[14]: type Memory, range 64, base 0xfebfa000, size 12, enabled
pcib11: requested memory range 0xfebfa000-0xfebfafff: good
pcib11: matched entry for 11.1.INTB
pcib11: slot 1 INTB hardwired to IRQ 18
found-> vendor=0x1106, dev=0x3044, revid=0xc0
domain=0, bus=11, slot=3, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x20 (8000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfebfb800, size 11, enabled
pcib11: requested memory range 0xfebfb800-0xfebfbfff: good
map[14]: type I/O Port, range 32, base 0xec00, size 7, enabled
pcib11: requested I/O range 0xec00-0xec7f: in range
pcib11: matched entry for 11.3.INTA
pcib11: slot 3 INTA hardwired to IRQ 18
found-> vendor=0x11ab, dev=0x4320, revid=0x14
domain=0, bus=11, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0017, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
intpin=a, irq=15
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfebfc000, size 14, enabled
pcib11: requested memory range 0xfebfc000-0xfebfffff: good
map[14]: type I/O Port, range 32, base 0xe800, size 8, enabled
pcib11: requested I/O range 0xe800-0xe8ff: in range
pcib11: matched entry for 11.4.INTA
pcib11: slot 4 INTA hardwired to IRQ 19
ahc0: <Adaptec 3960D Ultra160 SCSI adapter> port 0xe000-0xe0ff mem
0xfebf9000-0xfebf9fff irq 17 at device 1.0 on pci11
ahc0: Defaulting to MEMIO off
ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe000
ahc0: Reading SEEPROM...done.
ahc0: Manual SE Termination
ahc0: BIOS eeprom is present
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 423 instructions downloaded
ahc0: Features 0x1fef6, Bugs 0x40, Flags 0x28485560
ahc0: [MPSAFE]
ahc0: [ITHREAD]
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec 3960D Ultra160 SCSI adapter> port 0xe400-0xe4ff mem
0xfebfa000-0xfebfafff irq 18 at device 1.1 on pci11
ahc1: Defaulting to MEMIO off
ahc1: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe400
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 423 instructions downloaded
ahc1: Features 0x1fef6, Bugs 0x40, Flags 0x28485560
ahc1: [MPSAFE]
ahc1: [ITHREAD]
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
fwohci0: <VIA Fire II (VT6306)> port 0xec00-0xec7f mem
0xfebfb800-0xfebfbfff irq 18 at device 3.0 on pci11
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xfebfb800
fwohci0: [MPSAFE]
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:1e:8c:00:00:1a:99:a7
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:1e:8c:1a:99:a7
fwe0: bpf attached
fwe0: Ethernet address: 02:1e:8c:1a:99:a7
fwip0: <IP over FireWire> on firewire0
fwip0: bpf attached
fwip0: Firewire address: 00:1e:8c:00:00:1a:99:a7 @ 0xfffe00000000, S400, maxrec
2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x7d8c4000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
skc0: <Marvell Gigabit Ethernet> port 0xe800-0xe8ff mem
0xfebfc000-0xfebfffff irq 19 at device 4.0 on pci11
skc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xfebfc000
skc0: interrupt moderation is 100 us
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc0: chip ver = 0xb1
skc0: chip rev = 0x09
skc0: SK_EPROM0 = 0x10
skc0: SRAM size = 0x010000
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: bpf attached
sk0: Ethernet address: 00:1e:8c:75:19:0a
miibus1: <MII bus> on sk0
e1000phy1: <Marvell 88E1011 Gigabit PHY> PHY 0 on miibus1
e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
skc0: [MPSAFE]
skc0: [ITHREAD]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 57
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 58
sio0: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, generic (0), config:0x0, flags:0x3f0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 59
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ex_isa_identify()
ahc_isa_probe 8: ioport 0x8c00 alloc failed
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff pnpid ORM0000 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 60
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 61
ata1: [MPSAFE]
ata1: [ITHREAD]
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ukbd0: <Rextron USB, class 0/0, rev 1.10/1.01, addr 2> on uhub6
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
ums0: <Rextron USB, class 0/0, rev 1.10/1.01, addr 2> on uhub6
ums0: 5 buttons and Z dir.
Device configuration finished.
Reducing kern.maxvnodes 134057 -> 100000
procfs registered
lapic: Divisor 2, Frequency 166648467 hz
Timecounter "TSC" frequency 2999672289 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
Waiting 5 seconds for SCSI devices to settle
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
acd0: <PIONEER DVD-RW DVR-115D/1.13> DVDR drive at ata2 as master
acd0: read 6890KB/s (6890KB/s) write 5511KB/s (6890KB/s), 2000KB buffer, UDMA66
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
[ copious sound card debugging deleted ]
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
(probe100:ata2:0:0:0): error 22
(probe100:ata2:0:0:0): Unretryable Error
(probe100:ata2:0:0:0): Down reving Protocol Version from 2 to 0?
(probe93:sbp0:0:0:0): error 22
(probe93:sbp0:0:0:0): Unretryable Error
(probe94:sbp0:0:1:0): error 22
(probe94:sbp0:0:1:0): Unretryable Error
(probe95:sbp0:0:2:0): error 22
(probe95:sbp0:0:2:0): Unretryable Error
(probe96:sbp0:0:3:0): error 22
(probe96:sbp0:0:3:0): Unretryable Error
(probe97:sbp0:0:4:0): error 22
(probe97:sbp0:0:4:0): Unretryable Error
(probe98:sbp0:0:5:0): error 22
(probe98:sbp0:0:5:0): Unretryable Error
(probe99:sbp0:0:6:0): error 22
(probe99:sbp0:0:6:0): Unretryable Error
ahc0: Selection Timeout on A:0. 0 SCBs aborted
ahc1: Selection Timeout on A:5. 0 SCBs aborted
ahc0: Selection Timeout on A:1. 0 SCBs aborted
ahc1: Selection Timeout on A:6. 0 SCBs aborted
ahc0: Selection Timeout on A:2. 0 SCBs aborted
ahc1: Selection Timeout on A:12. 0 SCBs aborted
ahc0: Selection Timeout on A:3. 0 SCBs aborted
ahc1: Selection Timeout on A:13. 0 SCBs aborted
ahc0: Selection Timeout on A:4. 0 SCBs aborted
ahc1: Selection Timeout on A:0. 0 SCBs aborted
ahc0: Selection Timeout on A:5. 0 SCBs aborted
ahc1: Selection Timeout on A:1. 0 SCBs aborted
ahc0: Selection Timeout on A:6. 0 SCBs aborted
ahc1: Selection Timeout on A:2. 0 SCBs aborted
ahc0: Selection Timeout on A:8. 0 SCBs aborted
ahc1: Selection Timeout on A:4. 0 SCBs aborted
ahc0: Selection Timeout on A:9. 0 SCBs aborted
ahc1: Selection Timeout on A:8. 0 SCBs aborted
ahc0: Selection Timeout on A:10. 0 SCBs aborted
ahc1: Selection Timeout on A:9. 0 SCBs aborted
ahc0: Selection Timeout on A:11. 0 SCBs aborted
ahc1: Selection Timeout on A:10. 0 SCBs aborted
ahc0: Selection Timeout on A:12. 0 SCBs aborted
ahc1: Selection Timeout on A:11. 0 SCBs aborted
ahc0: Selection Timeout on A:13. 0 SCBs aborted
ahc1: Selection Timeout on A:14. 0 SCBs aborted
ahc0: Selection Timeout on A:14. 0 SCBs aborted
ahc1: Selection Timeout on A:15. 0 SCBs aborted
(probe81:ahc1:0:3:0): Down reving Protocol Version from 4 to 3?
(ahc1:A:3:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc1:A:3:0): Received PPR width 1, period 9, offset 40,options 2
Filtered to width 1, period 9, offset 40, options 2
ahc1: target 3 using 16bit transfers
ahc1: target 3 synchronous at 80.0MHz DT, offset = 0x40
(ahc1:A:3:0): Sending PPR bus_width 1, period 9, offset 40, ppr_options 2
(ahc1:A:3:0): Received PPR width 1, period 9, offset 40,options 2
Filtered to width 1, period 9, offset 40, options 2
ahc0: Selection Timeout on A:15. 0 SCBs aborted
pass0 at mpt0 bus 0 target 0 lun 0
pass0: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
pass0: Serial Number BV00P81007F1
pass0: 300.000MB/s transfers
pass0: Command Queueing Enabled
da0 at mpt0 bus 0 target 0 lun 0
da0: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
da0: Serial Number BV00P81007F1
da0: 300.000MB/s transfers
da0: Command Queueing Enabled
da0: 70136MB (143638992 512 byte sectors: 255H 63S/T 8941C)
da1 at mpt0 bus 0 target 1 lun 0
da1: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
da1: Serial Number BV00P7C007D2
da1: 300.000MB/s transfers
da1: Command Queueing Enabled
da1: 70136MB (143638992 512 byte sectors: 255H 63S/T 8941C)
da2 at mpt0 bus 0 target 2 lun 0
da2: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
da2: Serial Number BV00P7C007C9
da2: 300.000MB/s transfers
da2: Command Queueing Enabled
da2: 70136MB (143638992 512 byte sectors: 255H 63S/T 8941C)
da3 at mpt0 bus 0 target 3 lun 0
da3: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
da3: Serial Number BV00P81007EU
da3: 300.000MB/s transfers
da3: Command Queueing Enabled
da3: 70136MB (143638992 512 byte sectors: 255H 63S/T 8941C)
GEOM: new disk da0
GEOM: new disk da1
GEOM: new disk da2
GEOM: new disk da3
pass1 at mpt0 bus 0 target 1 lun 0
pass1: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
pass1: Serial Number BV00P7C007D2
pass1: 300.000MB/s transfers
pass1: Command Queueing Enabled
pass2 at mpt0 bus 0 target 2 lun 0
pass2: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
pass2: Serial Number BV00P7C007C9
pass2: 300.000MB/s transfers
pass2: Command Queueing Enabled
pass3 at mpt0 bus 0 target 3 lun 0
pass3: <FUJITSU MBC2073RC 0104> Fixed Direct Access SCSI-5 device
pass3: Serial Number BV00P81007EU
pass3: 300.000MB/s transfers
pass3: Command Queueing Enabled
pass4 at ahc1 bus 0 target 3 lun 0
pass4: <HP Ultrium 2-SCSI S63D> Removable Sequential Access SCSI-3 device
pass4: Serial Number HU108021EN
pass4: 160.000MB/s transfers (80.000MHz DT, offset 64, 16bit)
pass5 at ata2 bus 0 target 0 lun 0
pass5: <PIONEER DVD-RW DVR-115D 1.13> Removable CD-ROM SCSI-0 device
pass5: 66.000MB/s transfers
sa0 at ahc1 bus 0 target 3 lun 0
sa0: <HP Ultrium 2-SCSI S63D> Removable Sequential Access SCSI-3 device
sa0: Serial Number HU108021EN
sa0: 160.000MB/s transfers (80.000MHz DT, offset 64, 16bit)
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 4 to local APIC 1
ioapic0: Assigning ISA IRQ 6 to local APIC 0
ioapic0: Assigning ISA IRQ 9 to local APIC 1
ioapic0: Assigning ISA IRQ 14 to local APIC 0
ioapic0: Assigning ISA IRQ 15 to local APIC 1
ioapic0: Assigning PCI IRQ 16 to local APIC 0
ioapic0: Assigning PCI IRQ 17 to local APIC 1
ioapic0: Assigning PCI IRQ 18 to local APIC 0
ioapic0: Assigning PCI IRQ 19 to local APIC 1
ioapic0: Assigning PCI IRQ 21 to local APIC 0
ioapic0: Assigning PCI IRQ 22 to local APIC 1
ioapic0: Assigning PCI IRQ 23 to local APIC 0
msi: Assigning MSI IRQ 256 to local APIC 1
(cd0:ata2:0:0:0): error 6
(cd0:ata2:0:0:0): Unretryable Error
cd0 at ata2 bus 0 target 0 lun 0
cd0: <PIONEER DVD-RW DVR-115D 1.13> Removable CD-ROM SCSI-0 device
cd0: 66.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
GEOM: new disk cd0
(cd0:ata2:0:0:0): error 6
(cd0:ata2:0:0:0): Unretryable Error
(cd0:ata2:0:0:0): error 6
(cd0:ata2:0:0:0): Unretryable Error
(cd0:ata2:0:0:0): error 6
(cd0:ata2:0:0:0): Unretryable Error
(cd0:ata2:0:0:0): error 6
(cd0:ata2:0:0:0): Unretryable Error
Trying to mount root from ufs:/dev/da0s1a
start_init: trying /sbin/init
lo1: bpf attached
gif0: bpf attached
Linux ELF exec handler installed
msk0: link state changed to UP
mpt0: QUEUE FULL EVENT: Bus 0x00 Target 0x00 Depth 129
(noperiph:mpt0:0:0:0): tagged openings now 128